Ge Gsl25jfpabs Parts

• Fridge too cold
• Too warm
• Fridge runs too long
• Freezer too cold

I unplugged the fridge and took all the food and shelving out of the freezer and then proceeded to take off the bottom sliding drawer rack on both sides off (4 Phillips head screws). Then took off the light bulb cover and then the light bulb. Then the back wall that covers the coils and tubes that the refrigerant runs through ( 2 screws with hex head). After sliding out the back wall I could see that the entire coil area was frosted and iced up. I took a blow dryer and melted all of it over... Read more

• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

Much easier than expected, I was certain it had to be a water line but the solved everything Read more

• Too warm
• Frost buildup
• Fridge too warm
• Freezer not defrosting

I unplugged the fridge and took all the food and shelving out of the freezer and then proceeded to take off the bottom sliding drawer rack on both sides off (4 Phillips head screws). Then took off the light bulb cover and then the light bulb. Then the back wall that covers the coils and tubes that the refrigerant runs through ( 2 screws with hex head). After sliding out the back wall I could see that the entire coil area was frosted and iced up. I took a blow dryer and melted all of it over... Read more

I seared the web and found Appliance Parts Pros site and when I input my GE refrigerator model number I was able to do some diagnostics on their site. It was indicated from my research that the Water Inlet valve most likely was at fault for my problems. I ordered the replacement valve from them and they shipped the same day as the order and it arrived the next day, faster than I had expected. I viewed their video and it was very good at explaining what I had to do to replace the valve on my... Read more

• Freezer not defrosting
• Freezer too cold
• Not dispensing water
• Ice maker not making ice

I unplugged the fridge and took all the food and shelving out of the freezer and then proceeded to take off the bottom sliding drawer rack on both sides off (4 Phillips head screws). Then took off the light bulb cover and then the light bulb. Then the back wall that covers the coils and tubes that the refrigerant runs through ( 2 screws with hex head). After sliding out the back wall I could see that the entire coil area was frosted and iced up. I took a blow dryer and melted all of it over... Read more

• Ice maker dispenses too little ice
• Not dispensing water
• Ice maker won't dispense ice
• Ice maker not making ice

By visiting your website, viewing the repair instructions and ordering the right parts. Very easy to understand and to do the repair.. Read more

• Ice maker dispenses too little ice

This was a little more involved than I originally thought, but after watching the video on the site it wasn't so bad. They walk you through each step verbally and visibly so you can see exactly what to do. Replacing the auger took around 20 minutes, and only that long because the screw holding the ice shield was a bit tough to turn. I just applied gentle pressure and turned slowly until it became loose. The rest was fairly easy, but I did get a small cut from the ice crusher blades. Nothing... Read more

Changed out the valve and cleaned the lines out Read more

• Door sweating
• Frost buildup
• Ice maker won't dispense ice
• Freezer not defrosting

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

*NOTE: These comments regard my experience with GE model PSHS6PGZBESS. *Searched the web and reviewed several sites for water flow issue and diagnostic/repair and found Appliance Parts Pros. Watched their video for water-issue repair. The review validated the MWF Manifold repair part and its installation. In doing this research, I made a serendipitous discovery to repair the ice dispenser drip by replacing the Ice Door Assembly Flap part. Ordered both parts at standard shipping and... Read more

• Ice maker won't dispense ice
• Door sweating
• Frost buildup

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

Although the web ordering process was clear, I needed some "personal contact" via customer service. It took very little time to assure me the the parts were the correct ones and the video was easy to follow. When the parts arrived in 2 business days, it took only 30 mins. to complete the replacement of the slides. The video was a great way to assure there was no wasted time or effort. Read more

The new slides fit perfectly. One thing to mention is that the slide rails come with the slide bearings so you do not need to buy those separate. When I called I was told I needed the bearings so I bought 3 assuming I would be able to salvage the others. Turns out I did not need them. Read more

• Fridge runs too long

First, cleaned all the dirt and lint from the condenser radiator, the fan motor is in a metal housing holding the fan motor in place. look carefully and there is a sheet metal screw at the bottom of the housing, 1/4 inch screw head sheet metal screw. I removed the screw and that released the housing from the base of frig. then very carefully , I turn the housing with the fan motor still in the housing a worked out of the frig base where it would be easier to replace the bad motor. the... Read more

• Door latch failure
• Ice maker not making ice
• Not dispensing water
• Ice maker won't dispense ice

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

The indication was that when I tried to use the icemaker or water dispenser, the green LED on the front would dim and the ice maker dispenser wouldn't work. It was intermittent at first, but this indicated it may be a power management issue, in that insufficient voltage was getting to the ice dispenser motor. I unplugged the unit to reset the electronics for about a minute, and when I plugged it back it the compressor would try to turn on (solenoid or relay would click about every two... Read more