Ge Gud24essjdww Parts

This control support is the mounting bracket that secures the appliance control assembly, keeping the control panel stable and aligned for reliable operation. Replaces a worn or broken support to restore proper panel fit and reduce vibration. What it does:

• Holds the control board/panel in place to prevent sagging or misalignment
• Keeps control knobs and buttons properly positioned for accurate use
• Reduces vibration and rattling that can affect button/knob response
• Can prevent intermittent contact caused by a loose or damaged support

• One control support bracket

• Disconnect power (unplug the appliance or shut off the breaker) before starting any work
• Access usually requires removing the control panel or back panel; keep fasteners organized
• Install with original mounting screws; inspect surrounding clips and hardware for wear

This outer washer tub replaces a damaged or cracked 24" tub to restore proper water containment and drum rotation. It helps stop leaks and noisy operation so your washer can complete wash cycles reliably. What it does:

• Holds wash water and supports the inner drum during operation
• Prevents leaks caused by cracks, corrosion, or deformation
• Restores proper drum alignment to reduce noise and vibration
• Works with existing seals, bearings, and suspension when undamaged

• One 24" outer tub

• Disconnect power and water before starting any repair
• Inspect seals, bearings, and mounting hardware; replace as needed for a complete repair
• This part may require drum removal and basic tools; follow OEM service instructions

A replacement pin alignment used to correctly position and secure moving parts in appliance hinge or latch assemblies. Restores proper alignment to reduce sagging, rubbing, or uneven operation for smoother, quieter performance. What it does:

• Aligns and secures hinge or latch components to maintain correct movement and fit
• Helps stop door sag, binding, or uneven closing when the alignment pin is worn or damaged
• Reduces rubbing and noise caused by misaligned parts
• Restores proper clearance for seals and moving assemblies

• One pin alignment

• Refer to the appliance OEM service manual for model-specific removal and installation steps
• Disconnect power (or unplug) and, if applicable, remove stored contents before working on doors or hinges
• Use basic hand tools; avoid forcing parts or over-tightening fasteners to prevent damage
• If alignment issues persist after replacement, inspect associated hinges, brackets, and fasteners for wear

This 1/4-20 Taptite hex washer-head screw secures panels and internal components in your appliance. Its thread-forming design creates a tight, vibration-resistant hold in untapped metal to keep assemblies aligned when a fastener is missing or stripped.

• Fastens brackets, panels, and hardware to the cabinet/frame
• Taptite design forms threads in pre-punched, untapped holes for a secure fit
• Replaces missing, stripped, or rusted screws
• Helps reduce vibration and rattling from loose mounts

• Unplug the appliance; if servicing a washer, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the appropriate nut driver or socket until snug—do not overtighten

This is a hex pan thread screw used to secure appliance panels and components. It replaces missing or damaged fasteners to restore proper fit and reduce vibration or rattling. What it does

• Secures panels, brackets, or components to the appliance frame
• Restores tight fit where a worn or missing screw caused loose panels or rattling
• Provides a hex head drive for easy tightening with the correct socket or bit
• Matches OEM fastening points when replacing the original screw

• One hex pan thread screw

• Use the correct hex socket or driver to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or damage components
• Disconnect power or follow appliance safety procedures before servicing
• Keep removed hardware organized to confirm correct replacement

The Drain Pump is an OEM part for GE washing machines. It works to remove water from the washer tub at the end of each cycle.

Causes of a bad drain pump can include blockages in the pump mechanism from built-up debris or damage from attempts to manually clear obstructions. Wear over time may also affect pump function.

Symptoms of a bad drain pump include:

• Washer failing to fully drain water after cycles
• Excessively long drain times
• Water remaining or collecting in the bottom of the tub
• Potential leaks or overflow issues

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

This control knob assembly restores a solid, easy-to-grip selector on your appliance's console so you can accurately choose cycles and settings. It replaces broken or stripped knobs that slip, wobble, or fall off the control shaft.

• Attaches to the control/timer shaft so you can turn and set functions
• Replaces cracked, missing, or hub-stripped knobs
• Helps resolve free-spinning knobs or knobs that won't stay on
• Maintains correct shaft engagement and a clean, finished console appearance

• Disconnect power before servicing
• Pull the old knob straight off; avoid prying against the console
• Align the new knob with the flat/splined shaft and press until fully seated
• Inspect the shaft for wear or damage before forcing

This exhaust gasket seals the dryer's exhaust duct connection to contain airflow and keep lint out of the cabinet. A tight seal helps maintain drying performance and efficiency while reducing warm, moist air leakage behind the unit.

• Seals the joint between the exhaust duct and outlet/blower housing to prevent air and lint leaks
• Helps maintain proper airflow for consistent drying results
• Wear or damage can cause longer dry times and warm, humid air or lint behind the dryer
• Visible tears, flattening, or missing sections indicate the gasket should be replaced

• Disconnect power; turn off gas supply for gas models before servicing
• Pull the dryer forward, disconnect the vent, and remove panel(s) as needed to access the exhaust connection
• Remove the old gasket and residue; clean mating surfaces; seat the new gasket evenly
• Reassemble, reconnect the vent, ensure the external vent is clear, and check for air leaks

The Baffle is an OEM part for GE electric dryers. Located inside the dryer drum, it helps separate clothes and improves air circulation during tumbling cycles. 

To achieve consistent drying times, a dryer relies on balanced airflow penetrating all areas where clothes reside. The baffle creates divisions to ensure air fully surrounds each layer instead of bypassing some areas. Its raised ridges also help tumbling action by preventing clumps of clothes.

Symptoms of a bad baffle include:

• Slow, uneven drying requiring extra cycles  
• Certain areas of clothes remain damp while others over-dry
• Reduced airflow output from the vent due to blockage

Replacing it with the genuine GE baffle plate restores optimized air distribution within the drum. The part is also compatible with some Kenmore dryers that use GE elements.

This retaining clamp secures wiring, hoses, or small assemblies to keep them routed and stable, helping prevent rubbing and vibration that can lead to wear or intermittent issues. Use it to replace a broken or missing clamp. What it does:

• Holds wires, hoses, or tubing in place to prevent contact with moving parts
• Reduces vibration and rattling by keeping components secure
• Prevents chafing that can cause insulation wear or exposed wiring
• Restores proper routing after repairs or part replacement

• Disconnect power (and water if applicable) before accessing internal components
• Use appropriate hand tools; avoid over-tightening which can damage the clamp or secured part
• Inspect surrounding wiring/hoses for damage and replace if needed

This motor and pulley assembly drives the dryer drum so clothes tumble and dry evenly. Replacing a worn or damaged unit restores normal drum rotation and reduces noise for reliable drying performance. What it does:

• Spins the dryer drum by transferring motor power through the pulley and belt
• Stops drum rotation when the motor or pulley fails
• Helps prevent loud squealing or grinding caused by worn pulley bearings
• Can resolve symptoms like no tumbling, intermittent rotation, or abnormal noise during operation

• Disconnect power (unplug or shut off breaker) before servicing
• Basic hand tools required; follow the dryer model's service manual for disassembly
• Handle wiring connectors and mounting hardware carefully; verify secure connections
• Test run after installation to confirm proper drum rotation and quiet operation

This suspension rod assembly supports the wash tub in compatible top-load washers. It helps control vibration and keep loads balanced during spin for smoother, quieter operation and reduced banging or walking.

• Supports and stabilizes the washer tub within the cabinet
• Helps dampen vibration and maintain balance during spin cycles
• Common symptoms of failure: loud banging, excessive shaking/walking, off-balance errors, or a leaning/sagging tub
• Replace if the rod is bent, the spring is broken, or there's excessive tub movement

• Disconnect power and water supply before service; wear gloves and eye protection
• Support the tub before removing any suspension components
• Access from the top/front as your model requires; release the upper retainer, disengage the rod from the base, and seat the new assembly fully
• After installation, verify the tub is level and moves freely without rubbing

The Top Bearing is an OEM part for GE electric dryers. Located near the top of the drum assembly, it further supports rotational movement during tumbling.

Symptoms of a faulty top bearing include:

• Emergence of grinding or scraping noises from the upper drum area
• Resistance or lack of responsiveness to smooth drum spinning  
• Potential impacts to interconnected spinning components  

As a bearing used repeatedly over time, standard wear from lint and dust accumulation affects function. Impacts can also compromise integrity on occasion. 

Causes typically include normal wear and tear from prolonged rotational cycles. Heavy loads may accelerate deterioration too by adding strain.

This genuine GE replacement bearing restores reliable support at the top of spinning cycles. Compatible with some Hotpoint, RCA, and select Kenmore dryers too, it extends equipment life through dependable bearing operation once installed.

This complete microwave oven door assembly replaces a damaged or non-sealing outer door to restore safe operation and visible access to the cooking cavity. Fits as a factory-style replacement for compatible GE countertop and over-the-range microwaves. What it does:

• Replaces cracked, dented, or warped outer door panels that prevent proper closing or latching
• Restores a secure door seal so the oven can start and operate normally
• Provides a clear viewing window for monitoring food without opening the door
• Helps stop rattling or loose door movement caused by bent hinges or mounts

• Disconnect power at the breaker and unplug the appliance before starting any repair
• Handle the glass and trim carefully to avoid breakage or injury
• Verify door latch and hinge alignment during installation; small adjustments may be required