Ge Pdt825ssj2ss Parts

This replacement screw fastens and secures appliance components where a 1/4-28 threaded flange screw with an internal hex washer head is required. It restores proper fit and helps prevent movement or rattling of panels and assemblies. What it does:

• Secures panels, brackets and components that use a 1/4-28 threaded flange screw
• Internal hex washer head allows a compact, low-profile drive for tight spaces
• Helps stop looseness, vibration noise, and misalignment when the original fastener is missing or worn
• Matches OEM fit and fastening form for reliable reassembly

• Disconnect power and follow all appliance safety procedures before servicing
• Use the correct hex driver/socket to avoid stripping the head
• Tighten to snug fit—do not overtighten to avoid damaging threads or mating parts
• Replace with identical part number to ensure proper fit and function

This small plastic clip secures a refrigerator's wiring conduit or harness to the cabinet, keeping wires routed and protected from abrasion. It helps reduce strain on connections and prevents wires from contacting moving parts. What it does:

• Holds wiring conduit or harness in place to maintain neat routing
• Prevents wires from rubbing on sharp edges or moving components
• Reduces strain on electrical connections that can cause intermittent faults
• Helps maintain safe separation between wiring and high-heat or mechanical areas

• Turn power off at the appliance and unplug before inspecting or replacing wiring clips
• Remove access panels only as needed to reach the clip; avoid stressing surrounding wires
• Snap the clip into the original mounting slot or replace any damaged fasteners for a secure fit
• If wires show damage or burns, replace the wiring/harness

This drain pump hanger secures the washer's drain pump to the outer tub, keeping the pump and hoses aligned so the pump can remove water reliably. Use it to replace a cracked or broken support that lets the pump shift. What it does

• Holds the drain pump firmly in place and maintains proper pump alignment.
• Helps reduce pump vibration and noise from a loose or mispositioned pump.
• Prevents the pump from pulling on hoses or becoming dislodged during the spin/drain cycle.
• A worn or broken hanger can contribute to poor draining, intermittent drainage, or unusual pump noise.

• One drain pump hanger.

• Disconnect power to the washer before beginning any repair.
• Access typically via the washer's lower front or rear panel; follow for disassembly.
• Inspect and reuse mounting hardware and grommets if undamaged; replace if corroded or broken.

This left-side door trim piece restores the exterior appearance and proper fit of a damaged or worn appliance door. It replaces cracked, chipped, or loose trim to help the door close and sit correctly in the frame. What it does:

• Covers and protects the left edge of the door while providing a finished appearance
• Replaces cracked, broken, or cosmetically damaged trim
• Helps maintain correct alignment of the door edge and attachment points
• Secures to the door with factory mounting tabs or screws
• Useful when left-side trim has snapped, warped, or come loose

• One left side door trim

• Disconnect power and/or fuel supply before beginning any repair
• Use appropriate hand tools; support the door to prevent dropping or damage
• Inspect mounting tabs and nearby components; replace any broken fasteners
• Follow the appliance service manual for disassembly and torque/spec guidance

This control box bottom is the lower housing that protects and supports the appliance's control electronics, helping keep wiring and components secure from debris and moisture. Fits into the control assembly to restore proper enclosure and support. What it does:

• Provides a protective lower enclosure for the control board and wiring harness
• Helps keep dust, lint and moisture away from sensitive electronics
• Secures the control board and related connectors in their correct position
• Prevents rattling or movement that can cause loose connections or noise

• One control box bottom (base cover) as pictured

• Disconnect power before servicing to avoid shock or component damage
• Handle electronics carefully and avoid touching circuit contacts
• Installation typically requires basic hand tools and removal of the control housing

The Filter Adapter is an OEM component specifically designed for GE dishwashers. Located inside the dishwasher tub, it functions to strain out large food particles from water before it reaches the wash arms.  The adapter holds the removable wash/rinse filters in place during operation, functioning as an extension of the filtration system. 

Causes of a bad filter adapter can include cracks or breaks compromising its sealing surface, wear and tear deforming filter retention features over time, or buildup inhibiting functionality.

Symptoms of a bad filter adapter include:  

• Loose or falling out removable filters during washing  
• Bypassing of food particles around compromised seals
• Reduced lifespan of disposable filters placed in a faulty adapter
• Debris accumulation impacting spray arm performance

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This bottle blaster assembly supplies targeted wash water to the dishwasher's Bottle Jets to clean tall, narrow items like baby and sports bottles. Replace a damaged or clogged assembly to restore focused spray and top-rack cleaning performance. What it does:

• Routes wash water to the bottle jet nozzles for concentrated cleaning inside bottles and narrow openings
• Helps improve cleaning on items positioned over the Bottle Jets
• Failure symptoms include no spray from the bottle jets, poor upper-rack cleaning, leaks near the jet area, or visible cracks/damage

• 1 bottle blaster assembly

• Disconnect power and shut off water to the dishwasher before servicing
• Access the bottle jet area; release retaining clips/fasteners and note hose routing and connection points
• Transfer any reusable clips or seals from the original assembly if needed
• Fully seat connections; run a short cycle to check for leaks and proper jet spray

This insulation toe kick is a replacement panel that fits the refrigerator base to help block drafts and protect internal components under the cabinet. It restores the factory barrier that supports temperature stability and efficient operation. What it does

• Replaces damaged or missing toe-kick insulation that lets cold air escape beneath the appliance
• Helps reduce drafts and minimize warm air intrusion into the refrigerator cavity
• Protects wiring and components located in the toe-kick area from dust and debris
• Can help prevent uneven cooling or frost buildup that results from compromised base insulation

• One insulation toe kick panel

• Disconnect power to the appliance before starting any service
• Remove the existing toe kick/board and fasteners, then position the replacement so mounting tabs align with factory slots
• Avoid compressing or tearing the insulation; maintain original fit for proper performance

The Outer Door Assembly Kit is an OEM replacement part for GE dishwashers. It includes all of the key external door components needed for proper function, including the inner and outer door panels, sealing gaskets, locking mechanisms, and design elements. 

Causes of a bad outer door assembly can include wear and tear over time, especially to sealing gaskets which are prone to cracking. Higher humidity levels can accelerate this. Physical damage such as dents or cracks in the plastic panels will also necessitate replacement.

Symptoms of a bad outer door assembly include:

• Water leaks into the interior due to compromised seals 
• Difficulty closing and locking the door securely
• Gaskets that no longer create an airtight seal around the door perimeter
• Loose, sagging, or damaged door panels

This replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This wiring harness assembly connects the appliance's DC control and related components, restoring proper electrical connections for control and power signals. Use it to replace a damaged or faulty harness to help recover normal operation. What it does:

• Provides the factory-style wiring connections between the DC control and associated components
• Restores reliable power and signal paths to prevent intermittent operation
• Helps resolve symptoms such as no power to controlled circuits, erratic control behavior, or electrical faults
• Maintains correct routing and connector fit for OEM compatibility

• Disconnect power to the appliance before beginning any work.
• Compare the replacement harness to the original to ensure connector locations and routing.
• Route and secure the harness away from heat sources and moving parts; avoid pinched wires.

This coated upper FDT assembly is a direct replacement for the appliance's upper FDT structure, restoring worn or damaged upper components for reliable operation. It helps maintain alignment and reduces wear-related issues. What it does:

• Replaces the appliance's upper FDT assembly to restore proper fit and support.
• Provides the coated surface that helps protect mating parts from wear and abrasion.
• Helps correct symptoms such as rubbing or scraping noises, misalignment of the upper housing, and visible wear or damage.
• Restores the intended clearance and contact surfaces for smoother operation.

• One coated upper FDT assembly.

• Disconnect power to the appliance before starting any repair.
• Handle the coated surfaces with care to avoid scratching or damaging the finish.
• Retain and reuse existing mounting hardware unless replacement hardware is explicitly required.

This upper rack fold-down tine assembly replaces worn or rusted tines on your dishwasher's top rack. It restores secure, adjustable support so cups, bowls, and small items stay upright and protected during the wash.

• Provides adjustable rows of coated tines on the upper rack to hold items in place
• Folds flat to make room for larger dishes when needed
• Helps prevent tipping, chipping, and poor cleaning from items falling over
• Common signs: broken or missing tines, peeling coating and rust, items not staying upright on the upper rack

• Disconnect power to the dishwasher before servicing
• Pull the upper rack forward; release end stops to remove the rack if needed
• Unclip and remove the old fold-down tine assembly; align and snap the new assembly onto the rack wires in the same position
• Verify the tines fold and lock properly before running a cycle

This front tub spacer cushions and positions the washer tub to reduce vibration and keep the inner and outer tubs properly aligned during operation. It helps maintain smooth spin cycles and prevents metal-to-metal contact. What it does:

• Centers and supports the front of the washer tub to maintain proper drum alignment
• Absorbs movement to reduce vibration and noise during spin
• Prevents rubbing or contact between the tub and cabinet components
• Can be associated with symptoms like excessive vibration, rubbing sounds, or off-center spins

• Designed for direct replacement; inspect surrounding seals and mounts during service
• Use basic hand tools; follow the washer's service manual for safe disassembly and reassembly
• Disconnect power and water supply before beginning any repair