Ge Pfe29psdass Parts

The Flow Meter is an OEM replacement part for GE refrigerators. It is designed to monitor and regulate the flow of water into the refrigerator's ice maker and water dispenser, preventing overfilling or insufficient water supply. 

A bad flow meter can occur due to normal wear and tear, clogging or blockage in the water lines, or damage to the flow meter mechanism. If you notice symptoms such as low ice production, slow or weak water flow from the dispenser, or water leakage, it may indicate a need to replace the flow meter.

Symptoms of a bad flow meter include:

• Low ice production
• Slow or weak water flow from the dispenser
• Water leaks

Restore your refrigerator by replacing the faulty flow meter with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

Size: 8-32 t. Includes 12 screws.

This holder element assembly secures the appliance's heating element in the correct position so the element stays stable for consistent operation and safe performance. It's a direct-fit replacement for worn or damaged holders. What it does:

• Secures and supports the heating element inside the appliance to maintain proper alignment
• Prevents element sagging or contact with other components that can cause noise or arcing
• Helps reduce vibration and movement that can lead to intermittent heating
• Common symptom: visible holder damage, loose or shifted element, unusual noise during operation

• Disconnect power (unplug or switch off breaker) before starting any repair
• Allow appliance and element to fully cool before handling
• Handle the element and holder carefully to avoid bending or damaging the element

This tube clamp secures flexible water tubing to its fitting in refrigerators. It helps maintain a tight seal to prevent leaks and keeps lines from slipping off under normal operating pressure.

• Holds plastic or rubber tubing firmly on a barbed fitting or nipple
• Helps prevent drips and leaks at tube connection points
• Addresses loose or disconnected water lines
• Useful when tubing slips off or won't stay seated

• Disconnect power and shut off the water supply before servicing
• Position the clamp over the tube and fitting; compress with pliers and release to lock in place
• Ensure the clamp is centered and fully seated; tug-test the tube
• Restore water and power; check all connections for leaks

This hinge center assembly replaces the refrigerator's right-side hinge pivot to restore proper door alignment and smooth opening. It helps reduce door sag and improves sealing for better performance. What it does:

• Provides the central pivot point for the right refrigerator door hinge
• Restores correct door alignment and even closing when the door is sagging or crooked
• Reduces rubbing, binding, or grinding noises from the hinge area
• Helps maintain an effective door seal to prevent cold air loss

• One hinge center assembly (right side)

• Unplug the appliance and empty or support the door before starting work
• Support or brace the door while removing hinge fasteners to prevent dropping
• Reuse existing screws/bolts unless new hardware is specified by the manufacturer

This hex washer-head screw is used in dishwashers to secure panels, brackets, and other hardware. Replacing a missing or corroded fastener restores a tight, stable installation and helps stop looseness or vibration during cycles.

• Fastens dishwasher panels, brackets, trim, or mounts to the cabinet/frame
• Replaces lost or stripped hardware after service or installation
• Helps address loose or rattling panels and minor misalignment
• Stainless steel construction per OEM spec for moisture-prone environments

• Disconnect power and water supply before servicing the dishwasher
• Wear gloves; sheet metal edges can be sharp
• Start threads by hand to avoid cross-threading; tighten with an appropriate driver
• Do not overtighten, especially when threading into plastic

Replacement screw that secures panels, trim and internal brackets to keep appliance components stable and rattle-free. Use when originals are missing, stripped, or broken to restore proper fit and safe operation. What it does:

• Secures panels, control housings, trim and small brackets so parts stay aligned and stable.
• Replaces missing or damaged fasteners that cause rattling, vibration, or loose assemblies.
• Keeps electrical and mechanical components properly positioned for reliable operation.
• Intended as a direct replacement where the OEM screw specified for the application is required.

• Disconnect power and unplug the appliance before starting any repair.
• Use the correct screwdriver or bit and seat the screw squarely to avoid stripping the head or threads.
• Do not overtighten—stop when snug to prevent damage to panels or plastic components.
• Keep removed screws organized; replace only with the identical OEM screw for proper fit.

A left-hand closure door assembly that replaces a worn or broken door closure to restore proper sealing and smooth drawer/door operation. Helps stop drafts and keeps compartments closing correctly for reliable performance. What it does

• Guides and supports the left-side door/drawer as it closes to ensure proper alignment.
• Helps form a tight seal to reduce air leakage and maintain interior temperature.
• Prevents rattling or catching that can occur when the closure is damaged or worn.
• Commonly replaced when the door doesn't stay closed, binds, or leaves a visible gap.

• Disconnect power to the appliance before starting any repair.
• Basic hand tools are typically required; access may involve removing a drawer or trim panel.
• Handle parts carefully to avoid damaging surrounding panels or gaskets.

A left-hand hinge center assembly that secures the refrigerator door at the center hinge to restore proper support and alignment. Replaces a worn or damaged hinge center to reduce door sagging and improve smooth opening. What it does:

• Provides a stable pivot point at the door's center hinge for correct alignment and support.
• Helps stop door binding, uneven gaps, and rubbing by restoring proper hinge geometry.
• Transfers load between upper and lower hinge halves so the door closes and seals correctly.
• Designed as a direct-replacement service part matching OEM fit and function.

• Support the door before starting—remove or brace the door to prevent it from falling.
• Disconnect power to the appliance if working near electrical components or the light switch.
• Remove hinge fasteners and replace with the new hinge center; tighten hardware securely but do not over-torque.
• Check door alignment and operation after installation; adjust hinge mounting as needed for an even gap.

This stainless-steel freezer drawer front restores the exterior appearance and provides a clean, durable surface for the freezer drawer. Ideal when the original front is dented, scratched or cosmetically worn. What it does:

• Replaces the outer front panel for the freezer drawer to restore proper fit and appearance
• Provides a smooth, corrosion-resistant stainless finish that matches other stainless surfaces
• Helps maintain proper drawer alignment and tactile operation when the original front is bent or damaged
• Improves the refrigerator's visual appeal after front panel damage or wear

• Unplug the appliance or disconnect power before starting any repairs
• Remove the freezer drawer and any interior bins to access fasteners; handle and trim may need removal
• Use appropriate hand tools and protect surrounding surfaces from scratches during installation

This inverter compressor kit replaces a failed inverter-type compressor assembly to restore cooling performance in compatible refrigerators. Designed to match the OEM function and maintain efficient temperature control when the original compressor fails. What it does:

• Replaces the refrigerator's inverter compressor assembly to restore sealed-system compression
• Helps resolve symptoms like no cooling, warm fridge/freezer, or loud/different compressor noise when diagnosis confirms compressor failure
• Works with inverter-driven refrigeration systems that require a matched compressor module
• Intended for use only when compressor/isolation parts are confirmed to be the failed component

• Requires proper evacuation, recharge, and leak testing per EPA and OEM guidelines
• Ensure electrical isolation and follow lockout/tagout before servicing

This silicon controlled rectifier (SCR) switches and regulates power to heating or motor circuits, helping the appliance control temperature and run cycles reliably. It's a direct-fit electronic switching component used in a variety of control systems. What it does:

• Acts as an electronic switch to regulate AC power to heating elements or motors
• Helps control temperature output and maintain consistent cycle performance
• Can prevent unwanted continuous current flow when functioning properly
• Commonly replaced when ovens, ranges, or dryers fail to heat or cycle correctly

• One silicon controlled rectifier (SCR) as shown

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the SCR by its body; avoid touching terminals and static-sensitive areas
• Verify proper orientation and secure mounting; follow OEM wiring and torque practices

A hex washer-head screw that secures panels and components in household appliances, helping restore stable, rattle-free mounting. Ideal when a mounting screw is missing, stripped, or rusted. What it does:

• Fastens panels, brackets, and internal components with a 1/4-20 thread for secure connections
• Replaces missing or damaged screws that cause loose panels or vibration noises
• Restores proper alignment of parts to prevent rattling and wear
• Works where a hex washer-head profile is required for flush, locked seating

• One hex washer-head screw, 1/4-20 x 3/4

• Use the correct 1/4-inch hex or socket driver to avoid stripping the head
• Power off and unplug the appliance before accessing internal components
• Do not overtighten; snug until secure to avoid damaging threads or parts
• If screw threads are damaged, replace with the matching OEM part for best fit

This 8-18 x 3/4 machine screw fastens appliance panels and small brackets to keep components secure and stable. It's a direct-fit replacement screw used where the original hardware has stripped, broken, or gone missing. What it does:

• Secures access panels, mounting brackets, and small assemblies
• Restores proper alignment and reduces rattling or vibration
• Replaces stripped or damaged fasteners
• Keeps wiring and components held in place for safe operation

• Unplug the appliance or disconnect power before starting work
• Use the correct driver and size to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to parts
• Replace corroded or damaged fasteners for best results