Ge Wcsr4170g1ww Parts

A small push-in plug button used to fill or cover an access hole or trim opening and restore a finished appearance. Designed to snap into place for a secure fit and to keep dirt and moisture out. What it does:

• Covers unused holes or fastener openings to restore a finished look
• Helps keep dirt, moisture, and debris from entering cavities
• Holds trim or panels flush by filling gaps where a fastener or post is missing
• Commonly replaced when cracked, lost, loose, or causing rattles or gaps

• One plug button

• Disconnect power to the appliance before accessing panels or trim
• Typically snaps into place—press firmly until seated; may require removing trim for access
• Avoid prying with sharp tools that can damage surrounding surfaces
• Replace only with the exact part number to ensure proper fit and finish

This right-side end cap is a replacement trim/closure piece designed for the washer cabinet to restore proper fit and finish and help keep internals protected from debris. It replaces a damaged, cracked or missing end cap. What it does:

• Covers and protects the washer's right-side edge or mounting area from dust and moisture
• Restores a flush appearance where the original end cap was cracked or broken
• Helps prevent snagging on clothing or towels from a damaged trim piece
• Can reduce rattles or vibration caused by a loose or missing end cap

• Disconnect power to the appliance before beginning any work
• Usually secured with screws or clips; basic hand tools are typically all that's required
• Align the part to the right-side mounting location and fasten securely without over-tightening

This front panel assembly replaces a cracked, worn or damaged console face to restore your appliance's appearance and support the control components. It provides the outer housing for buttons, displays and mounting points. What it does

• Covers and protects the control area from spills, dust and impact.
• Provides mounting locations and alignment for buttons, switches and display components.
• Restores a secure, finished surface when the original panel is cracked, warped or missing.
• Resolves cosmetic issues and loose or misaligned controls that affect operation.

• One panel front assembly.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Remove any trim, bezels or clips carefully to avoid damaging adjacent parts; keep fasteners for reinstallation.
• Handle edges and mounting tabs gently; some panels use plastic clips that can break if forced.
• If the control components or display must be transferred, note connector locations and orientation before disconnecting.

This silicon controlled rectifier (SCR) is a replacement power-control semiconductor that helps regulate current to heating and motor circuits, restoring proper cycling and output in affected appliances. What it does:

• Controls and switches power to heating elements or motors by gating current flow
• Helps the appliance regulate temperature or motor speed when functioning correctly
• A failing SCR can cause no heat, intermittent heating, or erratic motor behavior
• Designed to mount to a flange with a .625-inch tab for electrical connection

• Always disconnect power at the breaker or unplug the appliance before servicing
• Handle the SCR by its edges; avoid touching terminals and observe ESD precautions when possible
• Verify proper orientation and secure mounting to the heatsink or chassis per the service manual

Size: 1/4 - 20 b.

This left-hand end cap is a direct-fit replacement part that helps secure the washer's left-side assembly and restores proper cabinet/drum alignment for smoother operation and reduced vibration. What it does:

• Caps and protects the left-side end of the washer assembly to prevent wear and debris entry
• Helps maintain proper alignment of the washer drum/cabinet on the left side
• Reduces noise, rubbing, or wobbling caused by a damaged or missing end cap
• Matches OEM fit and mounting points for straightforward replacement

• Disconnect power and water to the washer before starting any repair
• Basic hand tools may be required; some disassembly of the cabinet or front panel could be needed
• Inspect adjacent components (gaskets, seals, fasteners) for wear while replacing the end cap

This apron kit is used to convert the older 3 piece support apron to the new one piece apron. Kit includes: one piece rod support apron, spring clips, nut and bracket assembly, conduit, wire ties and instruction sheet.