Gfss6kxass Parts

This rubber grommet seals the suction/water pipe where it passes through the appliance cabinet to reduce leaks and dampen vibration. It restores a tight, durable seal to help prevent water intrusion and rattling. What it does:

• Cushions and seals the suction/water pipe where it passes through sheet metal or plastic.
• Reduces vibration and pipe movement that can cause noise or wear.
• Helps prevent water leaks or moisture entry at the cabinet penetration.
• Maintains a proper fit for tubing routing and component alignment.

• One rubber suction pipe grommet.

• Disconnect power and shut off water supply before servicing.
• Remove access panels as needed to reach the pipe penetration; press grommet into opening and route pipe through center.
• Replace any brittle, torn, or deformed grommets; do not force a damaged grommet into place.

This is the left-side freezer evaporator fan motor. It spins the fan to draw air across the evaporator coil and circulate cold air, restoring proper airflow, quieter operation, and stable temperatures when the original motor is weak, seized, or noisy.

• Circulates air across the freezer evaporator coil to move cold air through the compartment
• Supports even cooling and temperature recovery after door openings
• Helps limit frost buildup on the back panel by keeping air moving
• Failure symptoms include weak or no airflow, loud or intermittent fan noise, rising freezer temperature, or soft/melting ice

• Disconnect power before servicing; wear cut-resistant gloves
• Remove freezer drawers/shelves and the rear panel to access the motor
• Note wire orientation; transfer the existing fan blade and any reusable mounting hardware from the old motor
• Ensure the blade spins freely and the shroud is clear before restoring power and checking airflow

This PTC-style start relay mounts on the compressor and briefly powers the start winding so the compressor can start reliably. Replacing a weak or heat-damaged relay can restore cooling performance and stop repeated clicking from the compressor area.

• Supplies momentary power to the compressor's start winding at startup
• Opens automatically as the PTC warms, removing the start winding from the circuit
• Symptoms of a failing relay: compressor won't start, repeated clicking/humming, and rising temperatures
• Visual clues can include discoloration, melting, or a burnt odor on the relay housing

• Disconnect power and remove the rear lower access panel to reach the compressor
• Note wire locations and terminal orientation before removal; transfer wires one-for-one
• Push the new relay fully onto the compressor pins until seated securely
• Inspect the overload protector and wire terminals for heat damage; replace any burnt connectors before restoring power

This is a black French door trim assembly that restores the exterior appearance and proper sealing of compatible French-door refrigerators. It replaces worn or damaged trim to help doors close evenly and maintain a clean, finished look. What it does:

• Replaces damaged or cracked trim on a French-style refrigerator door
• Restores proper edge alignment so doors close and seal more reliably
• Improves cabinet appearance by covering exposed edges and hardware
• Helps prevent drafts and moisture intrusion along the door perimeter

• Intended for appliance technicians or experienced DIYers; disconnect power and empty door before beginning
• Basic hand tools typically required; support the door during removal/installation to avoid strain
• Inspect adjacent seals and hardware while installing; replace any worn gaskets or fasteners separately
• Follow manufacturer instructions for torque and alignment to ensure correct closing and sealing

This compressor overload is the start-protection device that helps the refrigerator compressor run safely and restart after an overcurrent or overload. Replacing a faulty overload restores reliable compressor starting and helps protect the compressor motor. What it does:

• Protects the compressor by interrupting power during an electrical overload or locked-rotor condition
• Works with the start relay to allow the compressor motor to start and run properly
• Common symptom: refrigerator not cooling because compressor won't start
• Other symptom: humming or buzzing from the compressor or intermittent starting

• One compressor overload (start device)

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle terminals carefully; install on the compressor per OEM orientation and secure connections

This dispenser cover assembly replaces the plastic trim that surrounds a refrigerator ice/water dispenser, restoring a clean appearance and protecting internal dispenser components from dirt and damage. It helps keep the dispenser area sealed and functioning as intended. What it does:

• Covers and protects dispenser controls, chute and internal components from spills, debris and wear
• Provides a finished, stable surface for dispensing ice or water
• Prevents gaps that can cause chipping or rubbing of items against the dispenser opening
• Common fix for cracked, broken, faded or loose dispenser trim

• One dispenser cover assembly

• Disconnect power to the appliance before beginning work to avoid electrical or mechanical hazards
• Remove any screws or retainers securing the old cover; handle plastic parts carefully to avoid cracking
• Test dispenser operation after installation and ensure all fasteners are secure