Gfwn1100 L1ww Parts

This outside drain hose directs wastewater from your washer to the household drain. Replace a cracked, kinked, or leaking hose to stop leaks and restore reliable draining at the end of each cycle.

• Routes discharge water from the drain pump to a standpipe, laundry tub, or sink
• Helps maintain proper flow during drain/spin to prevent backups
• Common signs of failure: water leaking behind the washer, slow or incomplete draining, or drain-related error messages
• Visual clues include cracks, pinholes, bulges, or severe kinks

• Disconnect power and water; pull the washer forward for access and place towels/bucket as needed
• Note hose routing and connection points; release clamps and remove the old hose
• Fully seat the new hose; reuse existing clamps/hangers as required. Route without kinks and maintain proper standpipe height
• Run a test drain/rinse and check all connections for leaks

This stacking kit secures a compatible dryer to a matching washer to create a safe, space-saving stacked laundry configuration. It helps stabilize the dryer and reduces movement during use for a more reliable setup. What it does:

• Provides brackets and mounting hardware to fasten the dryer to the washer
• Helps prevent the dryer from shifting or tipping when the washer is running
• Improves overall stability of stacked laundry appliances during normal operation
• Reduces vibration-related movement that can cause noise or misalignment

• Disconnect power to both appliances before installing and follow all manufacturer instructions
• Use only on compatible washer/dryer pairs
• Tighten hardware securely but avoid overtightening; follow torque guidance in OEM instructions

This motor assembly kit replaces a worn or failed motor to restore proper mechanical drive and motion in the appliance. It's a direct-fit replacement designed to match the original assembly's form and function. What it does:

• Replaces the appliance's motor assembly to restore spinning, stirring, or drive motion
• Stops symptoms like no movement, intermittent operation, or unusual humming from the motor area
• Restores correct mechanical linkage between the motor and driven components
• Matches OEM fit and mounting points to simplify replacement

• One motor assembly kit (single complete motor assembly)

• Turn off power to the appliance at the breaker or unplug before beginning any repair
• Follow OEM disassembly steps to access the motor area; keep fasteners and small parts organized
• Handle electrical connectors carefully; wiring matches diagrams before re-energizing

This siphon pipe is a washer drain component that forms part of the air-break assembly. It helps prevent unintended siphoning and backflow so the tub drains correctly without pulling water back in or continuously draining. What it does:

• Provides the pipe section of the washer's siphon break/air gap
• Maintains airflow to stop siphoning and backflow during drain and spin
• Supports consistent, complete draining
• Typical failure signs: leaks near the siphon break, cracking, or water draining back into the tub

• Includes one siphon pipe

• Disconnect power and turn off water before servicing
• Expect some residual water; have towels or a pan ready
• Note hose routing; transfer any clamps/fittings from the old pipe and seat connections fully
• After reassembly, run a brief fill/drain to check for leaks and proper draining

This is a replacement ST4-16 sheet-metal mounting screw used to secure panels and small components on compatible appliances. It restores proper fit and prevents loose or rattling parts for a secure repair. What it does:

• Fastens trim, access panels, brackets and small components to appliance chassis
• Replaces missing, stripped or damaged screws that cause loose panels or vibration
• Provides correct thread and length for original mounting locations (ST4-16 size)
• Helps maintain safe, gap-free panel alignment for normal operation

• Use the same screw size and thread type as the original; do not over-torque
• If thread engagement is poor, inspect mating hole for damage before reuse
• Wear safety glasses and disconnect power to the appliance before working on panels
• If multiple screws are missing or hardware is corroded, replace all like-for-like fasteners

This M5-16 metric machine screw secures service panels and internal components in compatible appliances, providing reliable fastening for repair and replacement. Use the correct screw to restore fit and function after disassembly or part replacement. What it does

• Fastens panels, brackets, and components where an M5 x 16 mm machine screw is specified
• Restores secure attachment after repair or replacement of parts
• Helps eliminate rattles, loose panels, or misaligned parts when the correct screw is used
• Small, corrosion-resistant finish (typical for appliance screws) for lasting hold

• One M5-16 machine screw

• Use the correct sized M5 driver or hex bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or component damage
• Disconnect power and follow appliance safety procedures before accessing internal parts
• If the original screw had washers or clips, reuse them or replace with equivalent hardware

This electronic main control replaces the appliance's central circuit board to restore normal operation and user interface response. It manages program selection, timing, and communication between sensors and motors for proper cycles. What it does:

• Receives user input and runs the appliance's programmed cycles
• Sends signals to motors, valves, heaters, and sensors to start/stop functions
• Can correct failures like unresponsive controls, incorrect cycles, or error-code behavior when board is faulty
• Helps restore display and touchpad responsiveness when the issue is electronic control failure

• Disconnect all power (unplug or shut off breaker) before starting any work
• Take photos of wiring and connector positions before removal to ensure correct reassembly
• Handle the board by edges and avoid touching circuitry; protect against static discharge

This rear counterweight helps restore proper balance to the appliance door or panel so it opens and closes smoothly and stays in position during use. It's a direct-fit replacement designed to match the original component. What it does:

• Balances the door/panel to reduce sagging and uneven movement
• Restores smooth opening and closing motion
• Helps stop unwanted rattling or shifting during operation
• Works with the original bracket and fasteners to maintain correct alignment

• Disconnect power (and water if applicable) before beginning service
• Support the door or panel while removing the old counterweight to prevent drop or injury
• Remove and reuse factory fasteners unless replacements are provided; tighten securely to OEM torque

This adjustable leg assembly replaces a damaged or worn leveling leg to stabilize and level your appliance, restoring safe, wobble-free operation. It provides an easy way to re-establish proper appliance height and balance. What it does:

• Replaces a broken, bent, or stripped leveling leg to stop rocking or uneven siting
• Allows height adjustment to level the appliance on uneven floors
• Helps maintain door alignment and proper drainage by keeping the cabinet square
• Reduces vibration and noise caused by an unstable appliance

• One complete leg assembly as shown

• Inspect mounting area and matching hardware before installation; replace any damaged clips or frames
• Support the appliance securely (use a jack or assistant) before removing the old leg to prevent tipping
• Hand-start any fasteners, then tighten to snug; avoid over-torquing which can damage threads

A spring-style drain hose clamp that secures flexible drain tubing to fittings to prevent leaks and hose separation. Durable metal construction keeps drain connections tight for reliable wastewater flow and trouble-free operation. What it does:

• Holds drain hose firmly to pump, elbow or spud to reduce leaks and disconnections
• Applies even compressive force around flexible tubing for a secure seal
• Helps stop water spraying or pooling caused by a loose hose connection
• Commonly used on appliance drain and discharge lines where a snug clamp is required

• One spring-style drain hose clamp

• Use pliers to expand the clamp, fit over the hose, then release to engage; avoid twisting the hose while seating
• Replace any cracked or brittle hose before clamping to ensure a leak-free repair
• Disconnect power and water if required by your appliance before accessing the drain connection

This pressure hose clamp secures the small vacuum/pressure hose to its fitting, keeping the hose in place so the appliance can accurately sense water level and cycle pressure. Simple, direct replacement for a worn or loose clamp. What it does:

• Holds the pressure/vacuum hose snugly to prevent leaks or hose detachment
• Helps maintain proper pressure signal for correct cycle and fill operation
• Commonly used when a loose or damaged clamp causes intermittent pressure-related symptoms
• Small replacement part that restores a firm hose connection

• Disconnect power (and water, if applicable) before servicing the appliance
• Use a small screwdriver or pliers to remove the old clamp and secure the new clamp in place
• Ensure the hose is fully seated on the fitting before tightening the clamp

This inlet pipe clamp secures the refrigerator water inlet line to the cabinet or valve, preventing movement and wear. Replaces a worn or broken clamp to help stop chafing and reduce the chance of leaks. What it does:

• Holds the water inlet pipe or tube firmly in place to prevent rubbing and stress at connections
• Helps maintain a steady water line position for proper water/ice dispensing
• Prevents pipe vibration or movement that can lead to leaks or line damage
• Commonly replaced when the original clamp is cracked, loose, or missing

• One inlet pipe clamp

• Turn off water supply and unplug the appliance before starting work
• Access may require removing a small panel or the toe grille depending on model
• Remove the old clamp and snap or fasten the new clamp in the same location; use appropriate fastener if required
• Inspect tubing and connections for damage while replacing the clamp