Ghda986ko3ss Parts

This dishwasher float sits in the tub and works with the float switch to control the fill level and prevent overfilling. Replace it if cracked or sticking to restore reliable water level control and help avoid leaks.

• Rises with the water level to trigger the float switch and stop filling at the correct point
• Helps prevent overfilling and door leaks
• Common symptoms of a damaged or obstructed float include continuous filling, overfill/leaks, or no/insufficient fill
• Restores consistent water level sensing when the original float is worn or missing

• Disconnect power and turn off the water supply
• Open the door and remove the lower rack
• Remove the float cover; pull the old float straight up and clear any debris from the well
• Insert the new float and verify free up-and-down movement before reassembly and testing

This fill funnel gasket seals the water-inlet funnel where water enters the dishwasher tub. Replacing a worn seal helps prevent drips at the inlet and keeps incoming water directed into the tub during the fill cycle.

• Provides a watertight seal between the fill funnel and tub wall
• Helps prevent leaks from the inlet area and under the toe-kick
• Directs incoming water properly into the tub during fill
• Replace if the gasket is cracked, deformed, or leaking

• Disconnect power and turn off the water supply before servicing
• Access the fill funnel area; remove the old gasket and clean the sealing surfaces
• Seat the new gasket evenly and ensure the funnel fully engages the opening
• Reassemble and run a short fill to check for leaks

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

This dome float is the replacement water-level float that helps the appliance sense and control the tub's water level, restoring reliable fill and shutoff behavior. Use this OEM-fit float when the original is cracked, stuck, or missing. What it does:

• Moves with rising and falling water to actuate the water-level mechanism and help prevent overfilling.
• Can reduce symptoms such as improper fill levels, continuous filling, or intermittent fill shutoff when the existing float is damaged or obstructed.
• Works as part of the washer's water sensing system—does not include electronic switches or housings unless shown.

• Disconnect power and unplug the appliance before starting any repair.
• Access may require removing the washer top or cabinet; follow your model's service instructions.
• Inspect surrounding hoses and clips; replace any damaged components and ensure the float moves freely.

This mounting bracket secures the dishwasher tub or inner components to the cabinet or frame, helping keep the appliance stable during cycles and preventing movement or misalignment. What it does:

• Provides a secure attachment point between the dishwasher and the cabinet or chassis
• Helps reduce rattling, shifting, and vibration during operation
• Keeps inner panels and assemblies aligned for proper door operation
• Supports correct positioning that can prevent wear on adjacent parts

• One dishwasher mounting bracket

• Intended for users comfortable with appliance repair; disconnect power and shut off water before starting
• Typical installation uses screws or clips—retain original fasteners unless replacement fasteners are specified
• Inspect surrounding mounting points and hardware; replace any damaged screws or tabs for a reliable fit

This mounting bracket secures the dishwasher rinse module/dispenser assembly so the dispenser stays properly positioned for reliable rinse-aid delivery. A correctly seated bracket helps prevent dispenser misalignment and related rinse-aid issues. What it does:

• Holds the rinse module/dispenser firmly in place inside the dishwasher tub or door
• Keeps the dispenser aligned so rinse aid can be released as designed
• Helps prevent dispenser rattling, shifting, or partial seating during cycles
• Can reduce symptoms like poor rinsing, visible spots, or uneven rinse-aid release

• Disconnect power to the appliance before starting any work for safety
• Basic hand tools (screwdriver, nut driver) are typically needed; follow OEM instructions
• Align the bracket and secure fasteners without over-tightening to avoid damage

This flapper vent is the replacement exhaust flap that helps control dryer airflow and keeps outside air, pests and debris from entering the vent when the dryer is off. Fits many GE dryer exhaust housings. What it does

• Opens during dryer operation to let moist air escape and closes when the dryer is off to block backdrafts.
• Restores proper airflow when a damaged or stuck flap is preventing venting.
• Helps reduce outside odors, drafts and pest entry through the exhaust opening.
• Works as a simple mechanical replacement—no electrical connections.

• Disconnect the dryer from power and, if applicable, turn off gas before servicing.
• Access the exterior vent or the dryer exhaust housing; replacement typically secures with screws or snaps into the vent housing.
• Inspect and clean the vent duct and housing before installing the new flap to ensure proper operation.

This is a replacement fastener screw used to secure panels and components on compatible appliances, restoring proper fit and reducing movement. It's a simple, direct replacement when an original screw is missing or damaged. What it does:

• Secures access panels, covers, or internal components to prevent rattling and movement
• Helps maintain proper alignment of parts so doors and panels close correctly
• Replaces missing, stripped, or broken screws that can cause loose parts or noise
• Restores the appliance's original fit where a matching OEM fastener is required

• One replacement screw

• Turn off and unplug the appliance before starting any repair
• Use the correct driver and avoid over-tightening to prevent stripping threads
• If the original screw was holding electrical components, ensure power is disconnected and follow OEM safety instructions

Color: Black

 The Upper Arm Spray Assembly is an OEM part for GE dishwashers. It is responsible for distributing water evenly throughout the dishwasher during the cleaning cycle, ensuring all dishes are thoroughly cleaned. The arm measures approximately 11 inches long.

You should replace the upper arm spray assembly if it becomes clogged, damaged, or worn out. Causes of a bad spray assembly can include mineral buildup from hard water, food particles blocking the spray holes, or physical damage such as cracks or breaks.

Symptoms of a bad upper arm spray assembly include:

• Poor cleaning performance, with dishes coming out dirty
• Uneven water distribution inside the dishwasher
• Visible cracks or blockages in the spray arm
• Unusual noises during the wash cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Upper Spray Arm Bearing is an OEM part for GE dishwashers. It supports the upper spray arm, allowing it to rotate smoothly and distribute water evenly throughout the dishwasher. This ensures that all dishes receive a thorough cleaning during each cycle.

Over time, the upper spray arm bearing can wear out or become damaged. Causes of a bad bearing can include repeated use, mineral buildup from hard water, or physical damage due to mishandling.

Symptoms of a bad Upper Spray Arm Bearing include:

• The upper spray arm not rotating properly
• Ineffective cleaning of dishes on the upper rack
• Unusual noises during the wash cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Interlock Switch Assembly is an OEM part for GE dishwashers. It is designed to ensure the dishwasher door is securely closed before the wash cycle begins, preventing leaks and ensuring the appliance operates safely.

Causes of a bad interlock switch can include wear and tear from frequent use, electrical issues, or physical damage to the switch or its housing. A malfunctioning switch can prevent the dishwasher from starting or cause it to stop mid-cycle.

Symptoms of a bad door interlock switch assembly include:

• Dishwasher not starting
• Interruption of wash cycles
• Door not latching securely
• Error codes related to door latch issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Flood Switch Assembly is an OEM part for GE dishwashers. This part detects water levels and prevent overfilling by shutting off the water supply if a potential flood condition is detected. 

Causes of a bad flood switch assembly can include electrical failures, wear and tear over time, or damage from water exposure. 

Symptoms of a bad flood switch assembly include:

• The dishwasher not filling with water properly
• The dishwasher overfilling or leaking
• Error codes related to water levels
• The dishwasher not starting or stopping mid-cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.