Ghws3605frr-Flwasher Parts

This clamp secures the washer's gasket in its groove so the seal stays seated during operation. Replacing a worn or damaged clamp helps maintain a tight seal and can reduce leaks caused by a loose or slipping gasket. What it does:

• Retains the washer gasket (seal) firmly against its mating surface
• Helps prevent water seepage when a gasket won't stay seated
• Replaces a stretched, rusted, or broken clamp/retaining ring
• Common symptoms: gasket pops off, water at the front/door area, or a visibly damaged/missing clamp

• 1 gasket clamp

• Disconnect power and turn off water before servicing
• Access the gasket area per your model's service procedure
• Note clamp orientation; carefully release tension with the proper tool or pliers
• Seat the gasket evenly, install the clamp uniformly in its groove, and run a quick test cycle to check for leaks

The Spring Suspension is an OEM part for GE washing machines. It is responsible for supporting the washer tub and reducing vibrations and movement during the wash and spin cycles.

Causes of a bad spring suspension can include wear and tear from regular use, overstressing from unbalanced loads, or material fatigue over time.

Symptoms of a bad spring suspension include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging noises during spinning
• The washer tub being off-balance or misaligned
• The washer moving or walking during operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This door striker secures the appliance door when closed, restoring reliable latch engagement for proper sealing and quieter operation. Replace a worn or broken striker to help the door stay closed and reduce rattling. What it does:

• Engages with the door latch to hold the door closed and maintain correct alignment.
• Helps maintain an effective seal to support normal appliance operation.
• Reduces door rattling or popping caused by a worn or damaged striker.
• Common symptom: door won't latch or stay closed, or it rattles during use.

• Disconnect power to the appliance before starting any repair; follow all manufacturer safety instructions.
• Remove only the fasteners shown in the OEM instructions; retain mounting hardware if reuse is intended.
• Align the striker with the latch and tighten hardware securely but avoid overtightening.

This machine screw secures panels, brackets, and internal components in compatible washers. Replacing a missing or stripped fastener restores a tight fit to help reduce vibration and keep parts properly aligned.

• 10-32 thread; 5/8-inch length; Torx T25 drive
• Fastens components and panels to resist loosening from vibration
• Replaces lost, corroded, or stripped screws
• Helps address loose or rattling panels, misalignment, or hardware that won't tighten

• Unplug the appliance and turn off water supply before servicing
• Use a T25 Torx driver; start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten
• Repair or replace the bracket/panel for a secure hold

A replacement pressure sensor that monitors air/differential pressure and sends a signal to the appliance control so the unit can respond correctly. Helps restore accurate pressure readings and resolve pressure-related faults and errors. What it does

• Detects air/differential pressure changes and reports them to the control board for proper system sequencing.
• Helps the control identify pressure faults and can affect diagnostic error codes or sensor-failure indications.
• A failed sensor may cause intermittent operation, incorrect diagnostics, or system faults tied to pressure monitoring.
• Works as the direct replacement sensor component—matches the OEM function when replacing a defective unit.

• One pressure sensor

• Disconnect power to the appliance before starting work to avoid shock or damage.
• If the sensor is in a water-connected circuit, shut off the water supply before removal.
• Handle the sensor and its electrical connector carefully; avoid contamination of sensing ports.
• Verify the part number and orientation before final installation and test the appliance after reassembly.

The Pump Filter Assembly is an OEM part for GE washers. This filter prevents debris, lint, and other foreign objects from entering and potentially clogging the washer pump. It traps and collects particles, allowing only clean water to flow through the pump and into the drainage system.

A bad pump filter assembly can occur due to accumulation of debris, damage to the filter housing, or wear and tear over time. If you notice symptoms such as slow or inadequate drainage, unusual noises during the pump cycle, or visible clogs in the filter, it may be time to replace the assembly.

Symptoms of a bad pump filter assembly include:

• Slow or inadequate drainage
• Unusual noises during the pump cycle
• Visible clogs or blockages in the filter

Prevent potential pump issues by replacing the faulty pump filter assembly with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
 

The dispenser drawer retainer secures the detergent/softener drawer in the washer housing so it opens smoothly without pulling all the way out. Replace a cracked or missing retainer to restore proper drawer alignment and retention.

• Holds the dispenser drawer in position and limits travel
• Helps prevent the drawer from falling out when opened
• Maintains alignment for smooth opening and closing
• Common symptoms: drawer pops out, won't stay seated, wobbles, or shows broken/missing clip

• Disconnect power and shut off water before servicing
• Pull the dispenser drawer out; depress the release to remove it
• Note the retainer's orientation, release its locking tabs, and snap in the new part
• Reinstall the drawer and test for smooth operation without forcing

The Washer Door Glass is an OEM part for GE washers. This glass serves as a protective barrier while allowing you to observe the washing process inside the machine. The door glass is designed to withstand the rigors of regular use and maintain transparency for a clear view of your laundry.

A bad door glass can occur due to accidental breakage or cracks over time. If you notice signs of damage, such as shattered or missing pieces, it may be time to replace the door glass.

Symptoms of a bad door glass include:

• Shattered or broken glass
• Visible cracks or chips
• Inability to see through the glass

Restore the function of your GE washer by replacing the damaged door glass with this genuine part. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This 10-18 Hi/Lo hex-washer screw is a direct-use replacement fastener for appliance panels, brackets and components. It restores secure mounting and helps stop loose trim, rattling or parts that shift during use. What it does:

• Secures panels, trim pieces, mounting brackets and similar components that use a 10-18 thread with a hex-washer head
• Restores proper fit where screws are missing, stripped, or corroded
• Helps eliminate rattling, vibration noise, and misaligned parts caused by loose fasteners
• Matches OEM head and thread style for a correct mechanical fit in specified locations

• Turn power or gas to the appliance off before working on electrical or gas-equipped units; unplug when applicable
• Use the correct sized hex driver or socket to avoid rounding the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging thin sheet metal
• If replacing multiple fasteners in a load-bearing area, replace all to ensure even fit and alignment

This long shipping bolt secures the washer's tub and suspension for transport, protecting internal components during delivery or relocation. Replace missing or damaged shipping hardware to safely immobilize the drum before moving the appliance.

• Threads into the designated transport points to lock the tub/suspension for moving
• Limits internal movement to help prevent damage to shocks, bearings, and hoses in transit
• Intended for preparing the washer for shipment or relocation; remove before use
• Use when the original long shipping bolt is missing, stripped, or damaged

• Unplug the washer and shut off water before installing or removing shipping bolts
• Refer to your model documentation for correct bolt locations and required quantity; some models use multiple bolts and different lengths
• Insert through the rear cabinet transport holes and tighten until snug; do not overtighten
• Remove all shipping bolts and save them for future moves before operating the washer

This clamp secures a hose or small tubing connection on compatible GE laundry appliances to help prevent leaks and keep the connection stable during operation. Durable metal construction resists vibration and wear. What it does:

• Holds a hose or tube firmly to a fitting to reduce leaks and loss of water or airflow
• Stops hose slippage caused by vibration or pressure changes
• Helps restore a tight connection after hose replacement or service
• Simple, low-profile design for use in confined appliance spaces

• Disconnect power and shut off water supply before servicing
• Drain hoses and remove remaining water to avoid spills
• Use the proper screwdriver or nut driver to tighten; do not over-tighten
• Inspect the hose and fitting for wear and replace if damaged before reinstalling the clamp

This hex-head screw secures dishwasher panels, brackets, and internal hardware so parts stay tight and rattle-free. Replace missing or stripped fasteners to restore a secure fit and reliable operation.

• Fastens panels, brackets, and other dishwasher components to the tub or frame
• Replaces a missing, stripped, or corroded screw that no longer holds securely
• Helps eliminate vibration and rattling caused by loose hardware
• Maintains proper alignment and secure mounting of parts during operation

• Disconnect power and shut off water supply before servicing
• Keep track of fastener locations and orientation for correct reassembly
• Start threads by hand; use an appropriate nut driver or socket to tighten
• Tighten snugly—do not overtighten, especially when threading into plastic

This leveling leg assembly supports and stabilizes your washer by allowing you to adjust its height for a level installation. Keeping the appliance level helps reduce vibration, noise, and movement during operation.

• Adjusts the washer's stance to ensure it sits level on the floor
• Helps prevent excessive vibration, walking, and rattling noises
• Supports proper spin performance by improving machine stability
• Common fix when a foot is worn, damaged, or will not hold adjustment

• Unplug the washer and turn off water supply before servicing
• Tip the appliance carefully to access the leveling point
• Thread the new leg into the base and adjust until level; lock if applicable
• Verify all legs contact the floor firmly and recheck level after test run

This OEM part is a washer user interface board assembly. It is the main control board that powers the control functions of the washer. Over time, a washer user interface board assembly can become inoperable after excessive use. If the washer is no longer turning on or the buttons are no longer responsive to touch, then the interface board assembly will need to be replaced. To replace this part, start by shutting off all power to the washer by either unplugging it or turning off the circuit breaker. Once it has been powered off, proceed to remove the control panel of the washer. This can be done using a flathead screwdriver or putty knife. Gently lift on the panel until it is released from its mounting tabs. Once removed, locate the user interface board assembly and unthread the screws that attach it to the control panel. Replace the old board with the new board and reinstall the control panel.This genuine replacement part is sourced directly from the manufacturer and is sold individually. It is compatible with General Electric, Hotpoint, and RCA brand appliances.

This 4-foot rubber inlet hose set supplies water to your appliance and replaces worn or leaking lines to restore proper water flow. Durable rubber construction resists kinks and flexing for reliable service. What it does:

• Connects the household water supply to the appliance so dispensers, ice makers or valves receive water
• Replaces cracked, split or leaking inlet hoses that cause visible leaks or water under the appliance
• Helps restore normal water flow when restricted or deteriorated tubing reduces supply
• Flexible rubber design allows easier routing behind appliances

• Turn off the water supply and unplug the appliance before installing
• Hand-start fittings to avoid cross-threading; tighten per the appliance/manual recommendations
• Inspect new hoses for damage before installation and check for leaks after restoring water

The Pin Damper is an OEM component specifically designed for GE washing machines. Located within the transmission housing, it provides a cushioning effect between the drive motor and gearing assemblies. 

Causes of a bad pin damper involve cracked rubber, sheared pins, or lack of lubrication from extended operational use over time.

Symptoms of a bad pin damper include:

• Grinding or vibration felt from transmission housing  
• Excessive noise emitted during gear-shifting changes
• Premature wear observed on drive shaft bushings/bearings

This OEM GE replacement pin damper helps reduce noise, protects components from impact shocks, and promotes smooth operation. Compatible with some Hotpoint, RCA, and Kenmore models as well, installation maintains optimized drivetrain performance.