Gld5604vooww Parts

A 10-24 x 1/2 thread-forming screw used to fasten panels and small components in appliances. Replaces missing or damaged fasteners to restore secure mounting and reduce rattling or misalignment. What it does:

• Secures panels, brackets, or trim to prevent movement and vibration
• Replaces missing, stripped, or damaged screws that allow parts to loosen
• Helps maintain proper alignment of doors and access panels
• Small, general-purpose fastener for a variety of appliance interior and exterior attachments

• Disconnect power to the appliance before beginning any repair
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread damage
• Compare the old screw to length and thread before installing

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

This is a replacement 8-18 x 9/16 machine screw used to secure internal and external appliance components. It restores proper fastening and helps stop rattling or loose panels caused by worn or missing fasteners. What it does

• Secures panels, brackets, or small assemblies to prevent movement and vibration
• Replaces stripped, corroded, or missing screws that can cause rattling or misalignment
• Helps maintain electrical and mechanical connections by holding parts in proper position
• Appropriate where an 8-18 thread size and 9/16" length are required

• Replacement screw

• Disconnect power to the appliance before accessing internal components
• Use the correct driver to avoid stripping the screw head and ensure proper torque
• Do not overtighten; snug until secure to avoid damaging threads or parts

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear. It replaces a worn or torn grommet to restore proper fit and quiet operation. What it does:

• Cushions metal-to-metal contact to reduce noise and vibration.
• Helps secure hoses, wiring, or panels where mounted through a hole.
• Prevents chafing and protects components from abrasion.
• Common symptom: rattling, rubbing sounds, or visible rubber deterioration.

• Turn off power to the appliance before starting any repair.
• Remove necessary panels or components to access the damaged grommet; note fastener locations for reassembly.
• Press or push the grommet into the mounting hole until fully seated; some installations may require a flat tool to ease placement.
• If grommet secures wiring or hoses, verify routing and clearance before restoring power.

This silicon controlled rectifier (SCR) switches and regulates power to heating or motor circuits, helping the appliance control temperature and run cycles reliably. It's a direct-fit electronic switching component used in a variety of control systems. What it does:

• Acts as an electronic switch to regulate AC power to heating elements or motors
• Helps control temperature output and maintain consistent cycle performance
• Can prevent unwanted continuous current flow when functioning properly
• Commonly replaced when ovens, ranges, or dryers fail to heat or cycle correctly

• One silicon controlled rectifier (SCR) as shown

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the SCR by its body; avoid touching terminals and static-sensitive areas
• Verify proper orientation and secure mounting; follow OEM wiring and torque practices

Color: blue-gray. It measures about 1-1/2 inches in diameter.

This fill funnel gasket seals the water-inlet funnel where water enters the dishwasher tub. Replacing a worn seal helps prevent drips at the inlet and keeps incoming water directed into the tub during the fill cycle.

• Provides a watertight seal between the fill funnel and tub wall
• Helps prevent leaks from the inlet area and under the toe-kick
• Directs incoming water properly into the tub during fill
• Replace if the gasket is cracked, deformed, or leaking

• Disconnect power and turn off the water supply before servicing
• Access the fill funnel area; remove the old gasket and clean the sealing surfaces
• Seat the new gasket evenly and ensure the funnel fully engages the opening
• Reassemble and run a short fill to check for leaks

This middle spray arm bracket secures the mid-level spray arm to the upper rack, keeping it centered and aligned so it spins freely and delivers even spray coverage for reliable cleaning performance.

• Supports and stabilizes the middle spray arm beneath the upper rack
• Maintains proper clearance for smooth rotation and spray pattern
• Replace if cracked, warped, or worn
• Common symptoms: middle arm falls off or won't spin, wobbles, scraping noises, or poor cleaning on the upper rack

• Disconnect power to the dishwasher before servicing
• Slide out the upper rack; release tabs or fasteners to remove the old bracket
• Transfer the spray arm to the new bracket and snap or secure it in place
• Spin the arm by hand to ensure free rotation before running a cycle

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

This dome float is the replacement water-level float that helps the appliance sense and control the tub's water level, restoring reliable fill and shutoff behavior. Use this OEM-fit float when the original is cracked, stuck, or missing. What it does:

• Moves with rising and falling water to actuate the water-level mechanism and help prevent overfilling.
• Can reduce symptoms such as improper fill levels, continuous filling, or intermittent fill shutoff when the existing float is damaged or obstructed.
• Works as part of the washer's water sensing system—does not include electronic switches or housings unless shown.

• Disconnect power and unplug the appliance before starting any repair.
• Access may require removing the washer top or cabinet; follow your model's service instructions.
• Inspect surrounding hoses and clips; replace any damaged components and ensure the float moves freely.

This inlet cover is a replacement trim piece that protects and finishes the washer's water inlet area, restoring a clean appearance and guarding internal inlet components from dirt and accidental contact. What it does

• Covers the water inlet opening and surrounding inlet assembly for a finished look
• Helps shield inlet valves and connections from debris and incidental contact
• Maintains proper alignment and fit of the inlet area trim
• Restores cosmetic appearance after damage or loss of the original cover

• One inlet cover

• Disconnect power and shut off water supply before starting any work
• Access may require removal of the washer top or control console depending on model
• Typically secures with clips or a few screws; have a screwdriver set on hand
• Replace if cracked or broken—do not attempt to use a damaged cover

A small rack clip that holds stemmed glasses upright during dishwasher cycles, reducing tipping and breakage. Restores proper support for wine glasses and other stemware so they wash safely and stay secure. What it does:

• Secures the stem of wine glasses and goblets to keep them stable during wash and rinse cycles.
• Prevents tipping, chipping, and breakage caused by glasses shifting in the rack.
• Replaces cracked, broken or missing stemware clips that allow dishes to move or clink.
• Helps reduce noise from glassware hitting the rack when the clip is damaged or absent.

• Remove dishes and ensure the dishwasher is off before replacing the clip.
• Seats into the dishwasher rack slot—press into place until fully seated; no special tools usually required.
• Refer to your appliance manual for model-specific instructions and safety guidance.

This mounting bracket secures the dishwasher rinse module/dispenser assembly so the dispenser stays properly positioned for reliable rinse-aid delivery. A correctly seated bracket helps prevent dispenser misalignment and related rinse-aid issues. What it does:

• Holds the rinse module/dispenser firmly in place inside the dishwasher tub or door
• Keeps the dispenser aligned so rinse aid can be released as designed
• Helps prevent dispenser rattling, shifting, or partial seating during cycles
• Can reduce symptoms like poor rinsing, visible spots, or uneven rinse-aid release

• Disconnect power to the appliance before starting any work for safety
• Basic hand tools (screwdriver, nut driver) are typically needed; follow OEM instructions
• Align the bracket and secure fasteners without over-tightening to avoid damage

This air diverter assembly routes and redirects airflow inside the appliance to help maintain proper venting and circulation. Replaces a worn or broken diverter to help restore normal airflow and reduce venting issues. What it does:

• Directs airflow between ducts and chambers to maintain intended ventilation paths
• Helps prevent air from bypassing heating elements or sensors
• Can reduce symptoms like uneven drying, long cycles, or reduced airflow
• Stops rattling or unusual air-noise caused by a broken or loose diverter

• One air diverter assembly

• Disconnect power before beginning any repairs
• Access may require removing the appliance back panel or cabinet; keep track of fasteners
• Inspect mating surfaces and seals; replace damaged seals or gaskets for best performance