Gsd3600g00cc/Rd7350248 Parts

This hose clamp secures a washer or dryer hose connection to help prevent leaks and keep hoses firmly attached during operation. It's a simple replacement for worn or loose hose fasteners. What it does:

• Holds inlet or drain hose to the appliance fitting to reduce slipping and leaks
• Restores a tight seal at hose connection points that may be leaking or wobbling
• Keeps hoses positioned correctly during fill and drain cycles
• Useful when clamp is rusted, stretched, or no longer grips reliably

• One hose clamp

• Disconnect power and turn off the water supply before replacing the clamp
• Slide clamp onto hose, position over the fitting, then compress or tighten per clamp type (use pliers or screwdriver as required)
• Inspect the hose and fitting; replace the hose if cracked or damaged
• Test for leaks after restoring power and water

A stainless steel hex-washer-head screw used to secure panels and components on compatible appliances. Corrosion-resistant construction helps maintain a secure fit where short, strong fasteners are required. What it does

• Fastens appliance panels, trim, or brackets where an 8-18 thread and short 3/8" length are specified
• Hex washer head provides a larger bearing surface to reduce pull-through
• Stainless finish resists rust in humid appliance areas
• Common replacement when original mounting screw is stripped, missing, or corroded

• One stainless steel hex-washer-head screw

• Use the correct 8-18 thread fastener and do not force mismatched screws to avoid thread damage
• Tighten securely but avoid overtightening to prevent stripped threads or cracked panels
• Power tools may be used with appropriate bit, but start by hand to ensure proper alignment
• If installing near electrical components, disconnect power before servicing

A 10-24 x 1/2 thread-forming screw used to fasten panels and small components in appliances. Replaces missing or damaged fasteners to restore secure mounting and reduce rattling or misalignment. What it does:

• Secures panels, brackets, or trim to prevent movement and vibration
• Replaces missing, stripped, or damaged screws that allow parts to loosen
• Helps maintain proper alignment of doors and access panels
• Small, general-purpose fastener for a variety of appliance interior and exterior attachments

• Disconnect power to the appliance before beginning any repair
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread damage
• Compare the old screw to length and thread before installing

Size: 8-32 x 5/8 inch.

A replacement knob latch handle that secures and indexes the appliance control knob for reliable selection and tactile feedback. Restores proper knob engagement to help prevent slipping or incomplete setting changes. What it does:

• Latches and holds the control knob in selected positions so settings stay engaged.
• Provides tactile detents for clear position feedback when turning the knob.
• Commonly replaces worn, cracked, or broken latch pieces that let the knob slip or fail to engage.
• Fits directly onto the control shaft and works with the existing knob assembly.

• Disconnect power (unplug or switch off circuit) before servicing to avoid shock or injury.
• Removal typically requires removing the control knob and/or console trim to access the latch; keep track of fasteners.
• Inspect the control shaft and surrounding components for wear; replace damaged knobs or retention clips as needed.

This is a genuine replacement screw used to secure components and panels on compatible GE appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or internal components to maintain proper alignment
• Stops rattling or vibration caused by loose fasteners
• Replaces missing, stripped, or damaged screws to restore safe operation
• Helps maintain seals and clearances by holding parts firmly in place

• Screw

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to components
• Keep removed fasteners organized to ensure correct reassembly

This long front panel replaces a damaged or worn control-area panel to restore the range's appearance and provide a secure mounting surface for control components. It fits the long control area used on select GE ranges. What it does:

• Replaces cracked, dented or heavily scratched front/control-area panels to improve appearance
• Provides the mounting surface and alignment for control switches and trim
• Helps keep internal components shielded from spills and debris near the controls
• Restores a flush fit where the original panel was warped or bent

• Disconnect power to the appliance (unplug or switch off breaker) before starting work
• Remove control knobs and any trim pieces to access mounting screws; keep original fasteners for reassembly
• Handle the panel carefully to avoid cuts from sharp edges and to prevent cosmetic damage
• Take care when disconnecting and reconnecting wiring;

The Lower Dishrack is an OEM part for GE dishwashers. It provides a sturdy shelf for placing pots, pans, plates, and other dishware on the bottom level of the dishwasher interior. The lower dishrack supports dish loads, holding them securely in place during the wash cycles. 

Causes of a failing lower dishrack include long-term wear and tear, corrosion from exposure to water and detergents, damage from improper loading, and loose or broken components.

Symptoms of a bad lower dishrack:

• Difficulty sliding the rack in and out
• The rack getting stuck mid-cycle
• Broken or missing wheels/rollers
• Rust formation
• Bent or misshapen wires

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This timer cover is the replacement trim that surrounds and protects the dryer or washer control timer on the control panel, restoring a finished look and shielding the timer mechanism from dust and debris. What it does:

• Replaces a cracked, faded, or damaged timer trim to improve appearance and protect the underlying timer assembly
• Helps keep lint, dust, and moisture away from the timer control area
• Restores correct alignment and mounting for the timer knob and control components
• Useful when the existing cover is loose, broken, or missing

• One timer cover

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the control panel or access bezel per your model's service instructions to reach the timer cover
• Use appropriate hand tools (screwdriver) and avoid forcing plastic tabs to prevent breakage

This rotary timer controls the sequence and length of dryer cycles so your machine advances through timed heating, cool-down, and drum-turn stages. It restores reliable cycle progression and timing when the original timer fails. What it does:

• Advances the dryer through selected cycles and timing intervals
• Turns power to the heating and motor circuits on/off at the correct points in a cycle
• Helps resolve symptoms like cycles that won't advance, the dryer stopping mid-cycle, or no heat occurring during timed cycles
• Works as the main user-programmable timing control for mechanical/timer-based dryers

• Turn power to the appliance off at the breaker before starting work to avoid shock.
• Handle the timer carefully to avoid bending terminals; match connector locations during reassembly.
• Some disassembly of the dryer console or control housing is required; keep track of screws and panel clips.

This support calrod assembly secures and positions the oven/range heating element so it heats evenly and stays stable during operation. Replaces a worn or damaged support to restore proper element alignment and reduce rubbing or sparking. What it does:

• Holds the tubular heating element in the correct orientation inside the oven or range
• Prevents the element from sagging, contacting interior surfaces, or vibrating during use
• Helps maintain consistent heating performance and reduces risk of element wear
• Common symptom: element rubbing, touching oven walls, or uneven heat distribution

• One support calrod assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Handle heating elements and support parts carefully to avoid bending or damaging the element
• Follow OEM service instructions for removal and reassembly; verify correct element alignment before restoring power