Gsd660g10ww Parts

This rubber grommet provides a protective seal where hoses, wires or components pass through openings, helping prevent chafing and moisture intrusion. Use it to restore a tight fit and reduce wear at the penetration point. What it does:

• Seals and cushions openings to help prevent water leaks and air gaps.
• Protects wiring and hoses from rubbing on sharp metal edges that can cause wear or shorts.
• Reduces vibration and rattling by holding parts securely in place.
• Common symptoms of failure: visible cracking, missing or torn grommet, water dripping near the opening, or rubbing noises.

• Disconnect power to the appliance and turn off water supply before beginning any repair.
• Remove the access panel or boot as needed to reach the opening; press the grommet into the hole until fully seated.
• Inspect surrounding seals, hoses and wiring; replace any damaged components to prevent repeat issues.

This SCR 8-18 silicon-controlled rectifier replaces the control semiconductor that switches and regulates power to heating or motor circuits in compatible appliances, restoring proper power delivery and control. It's a direct-fit electrical replacement part. What it does

• Acts as a switching device on control boards to allow or block current flow when signaled.
• Regulates power delivered to heating elements or motor circuits to enable proper operation.
• Commonly linked to symptoms like no heat or intermittent heating, motors that won't start, or erratic control-board behavior.
• Helps restore reliable on/off control when a failed SCR is causing open or shorted conditions.

• One SCR 8-18 silicon-controlled rectifier (WD02X10160).

• Always disconnect power before servicing the appliance to avoid shock.
• Handle the part carefully; avoid touching leads and use anti-static precautions if available.
• Inspect surrounding connectors and wiring for damage; replace any corroded terminals.

Replacement bracket that secures the flood/leak detection switch inside the appliance, keeping the switch positioned to sense unwanted water and help the leak-detection system work as intended. What it does:

• Holds the flood/leak switch in the correct position so it can detect water accumulation.
• Ensures consistent switch activation when water pools under the cabinet or base pan.
• Common repair when you find water under the appliance, persistent leaks, or when leak detection isn't responding.
• Simple, passive mounting part—no electrical function.

• Disconnect power and shut off the water supply before accessing the appliance.
• Remove the appropriate access panels to reach the bracket location; note orientation of the switch before removing.
• Reinstall bracket using the original fasteners or equivalent screws; keep parts organized during disassembly.
• Restore power/water and test the appliance for proper leak-detection operation after reassembly.

This push button is the user-facing control button that completes a control circuit when pressed, restoring responsiveness to a worn or broken selector interface. It provides a direct, replaceable way to fix unresponsive or stuck control input. What it does

• Acts as the external control button that engages the appliance's internal switch when pressed
• Restores tactile feedback and reliable control input if the original button is cracked, loose, or missing
• Common symptom fix: buttons that stick, don't depress fully, or fail to activate functions
• Works with the matched internal switch assembly to ensure consistent operation

• Disconnect power before any service
• Remove the control panel or bezel as needed to access the button; avoid prying on surrounding trim
• Replace the button by aligning and snapping it into the button housing; do not force or bend retaining tabs
• If the button does not restore function, inspect the underlying switch/mechanism for damage before ordering additional parts

This hose clamp secures a washer or dryer hose connection to help prevent leaks and keep hoses firmly attached during operation. It's a simple replacement for worn or loose hose fasteners. What it does:

• Holds inlet or drain hose to the appliance fitting to reduce slipping and leaks
• Restores a tight seal at hose connection points that may be leaking or wobbling
• Keeps hoses positioned correctly during fill and drain cycles
• Useful when clamp is rusted, stretched, or no longer grips reliably

• One hose clamp

• Disconnect power and turn off the water supply before replacing the clamp
• Slide clamp onto hose, position over the fitting, then compress or tighten per clamp type (use pliers or screwdriver as required)
• Inspect the hose and fitting; replace the hose if cracked or damaged
• Test for leaks after restoring power and water

A 10-24 x 1/2 thread-forming screw used to fasten panels and small components in appliances. Replaces missing or damaged fasteners to restore secure mounting and reduce rattling or misalignment. What it does:

• Secures panels, brackets, or trim to prevent movement and vibration
• Replaces missing, stripped, or damaged screws that allow parts to loosen
• Helps maintain proper alignment of doors and access panels
• Small, general-purpose fastener for a variety of appliance interior and exterior attachments

• Disconnect power to the appliance before beginning any repair
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread damage
• Compare the old screw to length and thread before installing

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

Size: 8-18 B 1HW 1/2 S N

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear. It replaces a worn or torn grommet to restore proper fit and quiet operation. What it does:

• Cushions metal-to-metal contact to reduce noise and vibration.
• Helps secure hoses, wiring, or panels where mounted through a hole.
• Prevents chafing and protects components from abrasion.
• Common symptom: rattling, rubbing sounds, or visible rubber deterioration.

• Turn off power to the appliance before starting any repair.
• Remove necessary panels or components to access the damaged grommet; note fastener locations for reassembly.
• Press or push the grommet into the mounting hole until fully seated; some installations may require a flat tool to ease placement.
• If grommet secures wiring or hoses, verify routing and clearance before restoring power.

Package of 12

Size: 8-18 x 7/8 inch.

This is a genuine replacement screw used to secure components and panels on compatible GE appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or internal components to maintain proper alignment
• Stops rattling or vibration caused by loose fasteners
• Replaces missing, stripped, or damaged screws to restore safe operation
• Helps maintain seals and clearances by holding parts firmly in place

• Screw

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to components
• Keep removed fasteners organized to ensure correct reassembly

The Middle Spray Arm Kit is an OEM replacement part specific to GE dishwashers. It contains the rotating center arm component that helps distribute water, dishwasher detergent, and moisture across the middle rack shelves for enhanced cleaning.

Causes of a bad middle spray arm can include clogged spray holes inhibiting proper water coverage, worn ball bearings reducing spray force, or broken or missing spray arm attachment clips.

Symptoms of a bad middle spray arm include:

• Items on middle racks not receiving sufficient cleaning
• Dried food or soap scum buildup is visible on rack shelves and dishes
• The arm fails to rotate or spin during cycles
• Detached spray arm is no longer connected to the dishwasher tub

This OEM GE replacement is compatible with many GE, Hotpoint, and Profile dishwasher models.

The Fine Filter Hub Nut is an OEM part for GE dishwashers. It secures the fine filter in place, ensuring that debris and food particles are effectively filtered out during the wash cycle, preventing them from re-entering the dishwasher tub.

Causes of a bad fine filter hub nut can include wear and tear from regular use, damage from over-tightening, or cracking due to impact. A faulty hub nut can lead to improper filtration, causing debris to circulate and potentially clog the dishwasher.

Symptoms of a bad Fine Filter Hub Nut include:

• Poor cleaning results with food particles left on dishes
• Unusual noises during the wash cycle
• The filter becoming loose or not staying in place

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.