Gsh22jdbbb Parts

This assembly meters cold air from the freezer into the fresh-food compartment and provides temperature feedback to the controls. Replacing a failing unit restores proper airflow and more stable, even cooling performance.

• Motorized damper door opens and closes to regulate airflow from the freezer; stuck-open can cause freezing near the vent, stuck-closed can leave the fresh-food section warm.
• Integrated thermistor senses compartment temperature and signals the control board; a failed sensor can cause erratic or inconsistent temperatures.
• Helps balance airflow between compartments to maintain set temperatures.
• Common clues include clicking/chattering from the damper area, weak or constant airflow, warm spots, or items freezing on upper shelves.

• Disconnect power before servicing.
• Access the damper through the fresh-food air duct; remove shelves and the duct cover as needed.
• Disconnect the wire harness; route and seat wiring and seals in the same positions during reassembly to prevent air leaks.
• Restore power and allow up to 24 hours for temperatures to stabilize.

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation

This refrigerator door gasket seals the fresh food compartment to keep cold air in and moisture out. A tight seal helps maintain proper temperatures and reduces frost and condensation around the door. What it does:

• Forms an airtight seal between the fresh food door and cabinet
• Helps stabilize refrigerator temperature and humidity
• Reduces condensation, frost, or moisture around the door perimeter
• Replaces torn, warped, or flattened gaskets that no longer seal

• 1 fresh food door gasket

• Disconnect power before servicing
• Warm the new gasket in hot tap water or with gentle low heat to relax folds and ease installation
• Clean the door channel; press the gasket fully into the retainer, starting at the corners
• Close the door and check the seal (paper test); adjust by gently warming and reshaping as needed

Size: 8-18 AB TSQ 5/8 SS

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This freezer door gasket creates an airtight seal around the door to keep cold air in and moisture out. Replacing a worn seal helps restore stable temperatures, reduce frost and condensation, and improve overall efficiency. What it does:

• Seals the perimeter of the freezer door to prevent air leaks and humidity intrusion
• Helps maintain consistent internal temperature and energy performance
• Replaces gaskets that are torn, warped, brittle, or won't stay seated
• Common symptoms include excess frost or ice near the door, condensation around the frame, or the door not closing flush

• 1 freezer door gasket

• Disconnect power before servicing
• Warm the new gasket in hot water or with a low-heat hair dryer to improve flexibility
• Remove the old gasket and press the new gasket fully into the door channel, starting at the corners
• Close the door and check for an even seal (use a "dollar bill" test); allow up to 24 hours for the gasket to relax and conform

Front mounting grommet.

This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.

• Secures covers, brackets, and trim to the appliance cabinet or liner
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration noise and loose or misaligned parts
• Maintains proper fit of guards, kickplates, or internal panels

• Disconnect power; turn off water supply if working near water lines
• Match to the original fastener to size and thread
• Start threads by hand to avoid cross-threading; tighten snugly, not excessively
• If threading into plastic, avoid overtightening to prevent damage

This part is a lower tail handle. This is a genuine OEM part made by General Electric and has been sourced directly from the manufacturer. This part is intended to replace a broken or detached tail handle on multiple different models and brands of refrigerators. The tail handle fixes to the exterior of the refrigerator. A missing or broken tail handle can prevent the door from functioning properly. The tail handle can become detached from the appliance with regular use and may require replacement. Always ensure the appliance is disconnected from its power source before attempting any repairs. Take appropriate safety precautions and wear protective work gloves. Proper tools are needed to install this part. For more accurate installation information on how and where to install this replacement lower tail handle, refer to the original manufacturer diagrams or owner's manual.As an authentic replacement part, this lower tail handle is suitable for use on various models of refrigerators manufactured by General Electric and Hotpoint. Please note that this is a genuine part made of high-quality and durable plastic and is sold individually.

This is the glass insert for the refrigerator pan cover, creating the flat shelf above the drawers. Replacing cracked or missing glass restores a stable, easy-to-clean surface and helps contain spills from reaching the storage areas below.

• Forms the flat shelf that tops the pan cover assembly over crisper/deli drawers
• Provides a sturdy surface for storing food items
• Helps contain small spills so they don't drip into drawers below
• Replace if the glass is cracked, shattered, chipped, bowed, or missing

• Disconnect power and remove food from the affected shelf area
• Lift out the pan cover frame and slide out the old glass
• Clean the frame's channels; seat the new glass fully and evenly
• Handle glass carefully and wear cut-resistant gloves

Size: 10-32 GXTT FLP.595 S

This replacement freezer door gasket creates a secure, flexible seal around the freezer door to help keep cold air in and warm air out, restoring proper door closure and helping the freezer maintain consistent temperature. What it does:

• Forms an airtight seal around the freezer door to reduce air leaks.
• Helps prevent frost and ice buildup inside the freezer.
• Restores proper door closure so the freezer maintains temperature more reliably.
• Reduces excess compressor cycling associated with a worn or damaged seal.

• Disconnect power or turn the appliance off before starting to avoid electrical hazards.
• Remove the old gasket and clean the door flange and mounting channel before installing the new seal.
• Press the new gasket fully into the channel, working around the door to ensure even seating and full contact.
• If the gasket feels stiff, follow OEM guidance or warm it gently to help it flex; avoid high heat that can damage the seal.

This PTCR is the PTC start relay for the refrigerator's compressor. It briefly energizes the start winding to get the compressor running, then opens as it warms, supporting reliable starts and helping protect the compressor from repeated restarts.

• Provides initial current to the compressor start winding, then self-limits as temperature rises
• Supports consistent compressor startup to restore and maintain cooling
• Typical failure symptoms: compressor clicks or hums but won't start; refrigerator warm or not cooling
• Visible signs may include discoloration or heat damage at the relay or connector

• Disconnect power before servicing; allow sealed-system components to cool
• Note the relay's orientation; firmly seat it on the compressor terminals
• Inspect the overload protector and wiring; replace any heat-damaged components
• If the compressor still won't start, further diagnosis of the compressor, overload, and capacitor is recommended

This OEM part is a refrigerator dispenser interface. The dispenser interface is responsible for the main functions of the refrigerator, such as adjusting the temperature settings as well as the other functions that are displayed on the interface. If the refrigerator is no longer cooling efficiently, failing to maintain temperature, dispensing water, or the touchpad is unresponsive, the interface might need to be replaced. Thankfully, replacing this part is not a difficult process.To replace the old interface, make sure that all power to the refrigerator is turned off. Open the refrigerator door and remove the door panel of the interior of the refrigerator. Locate the old control board and remove the wire harnesses that connect to it. Take note of the wire connector's orientation and reinsert the wires to the new board. Snap the new interface back in place and reinstall the inner panel. This genuine replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand refrigerators.

This evaporator fan bracket secures the evaporator fan assembly behind the rear panel. A rigid, correct-fit mount preserves blade clearance and airflow across the evaporator coils for steady temperatures while minimizing vibration and noise.

• Holds the evaporator fan assembly firmly in position
• Maintains alignment and clearance to prevent fan rubbing and excess noise
• Supports proper airflow through the evaporator compartment for consistent cooling
• Replace if the bracket is cracked, warped, or loose; symptoms may include rattling, scraping sounds, or the fan contacting the shroud

• Disconnect power before servicing and use cut-resistant gloves
• Remove shelves/drawers and the rear evaporator cover to access the fan assembly
• Transfer the fan motor and existing hardware to the new bracket; ensure the blade spins freely without contact
• Avoid damaging the evaporator coils; reassemble panels and restore power to test

This ice maker stripper is the front comb that helps release cubes from the ejector during harvest. It guides ice cleanly into the bin to reduce jams and keep ice production running smoothly. What it does

• Strips ice cubes off the ejector fingers as the ice maker cycles
• Directs cubes into the bucket, helping prevent jams and cube bridging
• Wear, cracks, or warping can cause cubes to stick, spill, or clump
• Symptoms include cubes piling at the front, clicking during harvest, or reduced/no ice

• 1 ice maker stripper

• Disconnect power and shut off water before servicing
• Remove the ice bin and access the ice maker front (remove cover if present)
• Release the old stripper (tabs/screws), align the new stripper with the ejector fingers, and seat it fully
• Reinstall cover and bin; restore power and allow a full cycle to verify operation