Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replaced Ice maker very easy. Read more
Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more
Color: white. It measures about 16.5 inches wide by 4 inches high by 5.5 inches deep.
Replaced shelves Read more
Fridge was making clicking noise and not cooling. Ice dispenser wasn’t working either. Research lead me to believe main board was out. YouTube video said to also replace compressor start relay and overload as well. Replaced all 3 parts in 15 minutes and back up and running. Read more
I ordered the heater unit from your website as well as a new evaporator panel gasket and thermostat. Once I removed the evaporator panel from the rear wall of the freezer side, I used a steamer machine I had to melt all the ice which had accumulated, I replaced the faulty heater unit and all is well. By-the-way, I consider your website amongst the very best and easy to use. I appreciate how well your developers and designers created the diagrams/pictures with numbered parts displayed,... Read more
Very easy to replace the trays slide the broken one out, slide the new one in, no problems. Read more
I had 2 parts that were cracked, so after changing the cracked parts as well as the dispenser switch, it was back to working normally. Simple to make the needed repairs and the videos provided on your website really helped in being prepared. Read more
I removed the drawers and old rails, and screwed in the new ones. It was very straightforward. Read more
Once I got the part in the mail, I washed it and installed it in less than 2 minutes. Didn't need any tools! Read more
Color: White
New solenoid Read more
Replacing the roller assembly corrected the problem. The key to replacing the roller assembly is elevating the refrigerator high enough to remove the roller assembly. (1) Raise and secure the refrigerator, (2) remove the metal bar across the bottom of the refrigerator to provide adequate access to the roller assembly (2-screws), (3) remove the roller assembly adjustment screw, (4) pry the roller pivot pin out, (5) pull the roller assembly toward the front of the refrigerator to remove, (6)... Read more
This replacement part is a snack pan slide rail, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This part is able to hold up other trays and racks in the refrigerator and freezer so that extra shelf space can be utilized. These slide rails can also hold up trays that can support heavy bottles and drinks. A new snack pan slide rail might be needed if the current ones have become stripped and are unable to latch onto the shelving to support it. It is common that these parts can become brittle over time as exposure to low temperature wears down the plastic. Be sure the shelving of the appliance is clear before attempting to replace the slide rail. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of appliances made by General Electric.
Ordered parts from appliance parts pros and completed installation myself Read more
I made the right initial move - I went to appliancepartspros.com and located the necessary parts. A video convinced me I could make the repairs myself. The correct parts were easily ordered and arrived quickly. I had no problem installing the parts using the knowledge I gained from the appliancepartspros.com video and the leak was fixed. Read more
Replaced motor and solenoid cube along with dispenser auger. Simply watched video on repair and installation and really had no problem. My refrigerator is so old that one of the holes in the motor did not align properly. Had to drill another hole to mount the motor to the housing, took ten minutes. The ice auger took the longest as I was afraid of breaking the plastic housing trying to get the tabs to release. Had to watch the video twice to make sure I got the blades back in the right order.... Read more