Gtd550hgd4ww Parts

The Thermostat is an OEM component specifically designed for GE laundry machines. It is a heat-sensing component that monitors and regulates air temperatures inside the dryer drum. Precise thermostat functioning ensures proper drying temperatures are reached and maintained for optimal performance.

Symptoms of a bad thermostat include:

• The dryer failing to heat or only heating intermittently  
• Unexpected temperature display readings or error codes
• Inconsistent moisture removal or garments not fully drying 

Causes include sensor degradation, electrical faults, or improper ventilation reducing its ability to accurately measure temperatures.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement part is a high-limit thermostat, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This high-limit thermostat is typically found in dryers and controls the heat inside the drying tub. This is especially important as different dryer settings require different amounts of heat. If the high limit thermostat works properly, the temperature inside the tub should reach the correct amount during each drying cycle with no issues. A new high-limit thermostat might be needed if the user notices that the dryer is unable to reach the appropriate level of heat for a certain drying cycle. This is also true if the dryer is becoming too hot when the heat is supposed to be set to low. Make sure the dryer is cooled down prior to replacing this part as the areas in the back of the dryer can become very hot during use. Be sure to reference the specific user manual for more instructions on how to replace the thermostat. This thermostat is sold individually and is a genuine OEM part. The thermostat is sourced directly from the manufacturer.

This dryer thermostat senses exhaust air temperature and opens or closes the heater circuit to keep drying temperatures consistent. Replacing a failed thermostat can restore proper heat control and help prevent overheating that can trip safety devices.

• Regulates dryer heat by cycling power to the heater based on sensed temperature
• Helps protect the appliance by interrupting heat if temperatures rise beyond its calibration
• Common symptoms: no heat or intermittent heat, long dry times, dryer runs too hot, temperature swings
• Replace if it fails continuity checks or is out of spec per your model's service information

• Disconnect power; for gas models, also shut off gas supply
• Allow the dryer to cool before servicing
• Access the thermostat on the blower or heater duct (varies by model); transfer wires one at a time and mount the thermostat flush to the surface
• Clear lint and verify vent airflow before testing operation

The Bearing Top Assembly is an OEM part for GE dryers. This assembly contains the capped metal shafts and roller bearings that smoothly rotate the dryer drum during cycles.

Causes of a bad bearing top assembly include worn or rusted bearings crying out for replacement, bent shafts putting pressure on parts, or detached mounting brackets creating imbalance. Repeated use deteriorates all drivetrain components.

Symptoms of a bad bearing top assembly include:

• Drum unable to tumble or spin as required
• Loud grinding/groaning noises during drying
• Excessive vibrations felt through the machine
• Bearings visibly seized up or shafts noticeably bent

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

This Thermostat is an OEM part for GE dryers. As a critical component in regulating the dryer's temperature, this thermostat ensures that the machine operates within a safe and efficient heat range. It monitors and controls the heat level, preventing the dryer from overheating while maintaining optimal drying conditions.

The need to replace the thermostat can arise from a variety of issues, including electrical problems, wear and tear, or a malfunction due to overheating. A failing thermostat can significantly impact the dryer's performance and safety.

Symptoms of a faulty Thermostat include:

• The dryer not heating up properly or overheating.
• Clothes taking longer than usual to dry.
• The dryer shuts off prematurely or not starting.
• Inconsistent heating leads to unevenly dried clothes.
• Potential safety hazards if the dryer overheats.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Thermostat is an OEM part for GE dryers. It senses and monitors air temperatures inside the dryer drum during cycles to ensure they remain within a designated range. As a safety component, the thermostat automatically cuts power if temperatures get too high, protecting the dryer.

The causes of a bad thermostat can be normal wear and tear over time. Repeated exposure to high heat, mineral deposits, electrical faults, or physical impacts may also cause premature malfunction. 

Symptoms of a bad thermostat include:

• The dryer fails to heat air properly during cycles
• Unexpected fluctuation of temperatures inside the drum
• Inaccurate temperature readings that impact drying performance
• Potential overheating errors or safety issues  

This OEM GE replacement thermostat restores the dryer's ability to gauge and regulate safe air temperatures as intended once more. Some Hotpoint, RCA, and select Kenmore models may also be compatible.

This GE Rotary Switch is an OEM replacement part for GE dryers. Specifically designed to ensure seamless compatibility and efficient performance, this rotary switch is a crucial component for controlling various dryer functions. 

Over time, rotary switches can wear out or get damaged due to frequent use or power surges. A malfunctioning switch may not provide accurate control over the dryer settings, leading to underperformance or safety issues. It's crucial to address any switch-related problems promptly to maintain the dryer's functionality and safety.

Symptoms of a bad Rotary Switch include:

• Difficulty in turning the switch or a switch that feels stuck.
• Inconsistent or non-responsive dryer settings.
• The dryer fails to start or stops mid-cycle.
• Unusual noises when turning the switch.
• Electrical shorting or sparking was observed at the switch location.

This GE OEM replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This GE Motor Drive and Pulley is an OEM part for GE dryers. The motor drive powers the drum, and the pulley system ensures proper tension and alignment of the belt. 

The need for replacement can arise from various factors such as prolonged use, electrical issues, or mechanical wear and tear. A failing motor drive and pulley can significantly impact the dryer's performance.

Symptoms of a malfunctioning Motor Drive and Pulley include:

• The dryer drum struggles to turn or doesn't turn at all.
• Unusual noises like humming or grinding during operation.
• The dryer stops unexpectedly during a cycle.
• Overheating of the dryer motor.
• The dryer takes longer than usual to dry clothes.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

Hi-limit thermostat. L210.

This gas dryer igniter assembly heats to a bright glow to light the burner so the dryer can produce heat. Replacing a cracked, weak, or non-glowing igniter restores reliable ignition and proper drying performance.

• Heats and ignites the gas at the burner to start the flame
• Restores drying heat when the original igniter is cracked or electrically open
• Common symptoms include: dryer runs but no heat, burner never lights, igniter does not glow, or extended dry times
• Visual damage such as white spots, breaks, or crumbling on the element indicates failure

• Disconnect power and shut off gas supply before servicing
• The igniter is brittle—handle only by the base or bracket; avoid touching the element with bare fingers
• Mount in the same position as the original and route leads away from heat and moving parts
• After reassembly, run a heat cycle to check the burner ignites; also check the flame sensor and gas valve coils

The Blower Wheel is an OEM component specifically designed for GE dryers. It is responsible for circulating air during the drying cycle, directing airflow through lint and clothes to remove moisture. The plastic blades of the blower wheel push air through the dryer and out the vent when the motor is running. 

Symptoms of a bad blower wheel include:

• Slow or inefficient drying times even on low moisture loads    
• Strange noises from inside the dryer cabinet      
• Excessive vibrations felt through the dryer door or cabinet
• Bent or cracked blower wheel blades

Causes can include normal wear and tear over time, accidents that damage the blades, or failures in the secure mounting of the blower wheel.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This replacement blower wheel for a dryer mounts to the drive motor and pulls air through the drum, lint filter, and exhaust, restoring proper airflow so loads dry efficiently and the appliance runs as intended. What it does:

• Spins with the motor to move air through the drum, lint screen, and exhaust duct
• Maintains airflow needed for even drying and temperature control
• Wear, cracks, or a stripped hub can cause long dry times and weak vent airflow
• Damage or imbalance may produce rattling, scraping, or vibration noises from the blower area

• 1 blower wheel

• Disconnect power; turn off gas supply for gas models before servicing
• Access the blower housing and remove the old wheel from the motor shaft per your model's design
• Clean lint and debris from the blower housing and exhaust duct while open
• Seat the new wheel fully and verify free rotation without rubbing before reassembly

The Trap Duct Slides are an OEM part for GE dryers. These slides are integral to the dryer's lint trap system, providing a smooth surface for the lint screen to slide in and out easily. This ensures efficient lint trapping and removal.

Replacement of the trap duct slides may be necessary due to wear and tear, damage, or if they become clogged with lint over time. 

Symptoms of a bad Trap Duct Slides include:

• Difficulty in inserting or removing the lint screen.
• Excessive lint accumulation outside the trap area.
• Reduced drying efficiency, possibly due to restricted airflow.
• Visible wear or damage to the slides, hindering the movement of the lint screen.
• Potential for increased risk of overheating if lint is not properly trapped.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This valve and pipe assembly regulates and routes fuel through the dryer's system so the burner can ignite and maintain heat. Replacing a failing assembly restores reliable heating performance and consistent drying results. What it does

• Opens and closes to control fuel flow to the burner when heat is called for
• Directs fuel from the inlet to the burner orifice through a rigid manifold/pipe
• Helps maintain safe shutoff when the dryer is idle
• Common symptoms of a failing assembly: no heat, intermittent heat, or burner failing to ignite

• One valve-and-pipe assembly

• Disconnect power and shut off the gas supply before servicing
• Use only gas-rated fittings/sealant as specified by the manufacturer; do not overtighten connections
• After installation, check all joints for leaks with a soap-and-water solution
• Restore power and gas, then verify proper burner ignition and stable heating

This replacement screw secures dryer panels and assemblies, helping prevent vibration and keeping components properly aligned. Use it to replace missing or stripped hardware and restore a solid, factory-tight fit during reassembly.

• Secures panels, brackets, and internal assemblies in the dryer cabinet
• Replaces lost, damaged, or stripped factory screw
• Helps reduce vibration and rattling caused by loose hardware
• Supports proper alignment of parts and a tight fit
• Symptoms can include loose or shifting panels, rattling noises, or gaps

• Disconnect power before servicing; for gas dryers, also shut off the gas supply if moving the unit.
• Match screw length and location to the original during reassembly.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Use the correct driver for your screw head style as used on your model.

The Backsplash is an OEM replacement part for GE dryers. It houses the buttons and controls necessary for operating and customizing your dryer's settings. This control panel provides a user-friendly interface for selecting drying cycles, temperature settings, and other options.  

Symptoms of a faulty control panel include:

• Unresponsive buttons or control settings
• Error messages displayed on the control panel
• Inability to select or change drying options

A bad control panel can be caused by wear and tear over time, physical damage, or electronic malfunctions. If you notice unresponsive buttons, error messages on the display, or any issues with the control panel's functionality, it may be time to replace the old or damaged control panel with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.