Gtd550hgd4ww Parts

This white cover replaces a cracked, loose, or missing trim/cover piece on your dryer to protect the underlying opening or component and restore a clean, finished look. It also helps keep dust and debris out of the cabinet. What it does:

• Conceals and protects the designated opening/component on the dryer
• Restores proper fit and finish to the cabinet or console
• Helps keep dust and debris out of internal areas
• Common signs you need this part: broken tabs, cracks, rattling, or a missing cover

• 1 white cover

• Disconnect power to the appliance before servicing
• Use care around sharp cabinet edges; wear cut-resistant gloves
• Note orientation, remove old cover, and transfer any reusable clips/grommets if present
• Reuse existing fasteners and avoid overtightening to prevent cracking

This control board and chassis assembly replaces a failed electronic control in your dryer. Installing a new assembly restores responsive controls and dependable cycle selection so the appliance starts and runs as expected.

• Houses the control electronics and communicates your selections to the dryer's control system
• Enables start/stop and option selection from the control panel
• Resolves: dead or unlit panel, buttons not responding, cannot start or change settings, intermittent or erratic panel behavior

• Disconnect power to the dryer before servicing
• Use ESD precautions; handle the board by the edges and avoid touching components
• Photograph/label wire connectors and transfer any reusable console parts from the original assembly if required
• Reassemble the panel and run a test cycle to verify operation

This factory screw secures dryer panels and internal components, keeping assemblies tight and aligned so the machine operates safely and without vibration or rattling.

• Fastens sheet-metal panels, brackets, or trim to the dryer cabinet/frame
• A loose or missing screw can cause panel vibration, noise, or misalignment
• Helps restore stability after service or when original hardware is lost
• Typical symptoms include rattling, loose panels, or gaps in trim

• Unplug the dryer before servicing
• Keep track of original screw locations and lengths; replace like-for-like
• Start screws by hand to avoid cross-threading, then snug—do not overtighten
• If threads are damaged, inspect mating hole or clip before installing

This is the drive motor and pulley assembly for GE dryers. It turns the drum via the belt and powers the blower wheel, restoring proper tumbling and airflow when the original motor is weak, noisy, or not starting.

• Powers the drive belt to rotate the dryer drum
• Turns the blower wheel to move air through the drum and exhaust
• Typical symptoms of a failing motor: dryer won't start, drum won't turn, loud humming/buzzing, or stops mid-cycle from overheating
• Restores consistent tumbling and drying performance

• Disconnect power; for gas models, also shut off the gas supply
• Access the motor by removing panels and relieving belt tension; remove drum as needed
• Label/photograph wiring and transfer the blower wheel and any brackets or clamps from the old motor
• Spin the drum by hand before restoring power

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

This dryer idler arm assembly keeps the drive belt tight and aligned so the drum turns smoothly. A worn or seized idler can cause squealing, belt slippage, or a drum that won't tumble.

• Applies tension to the drive belt and guides it around the motor pulley
• Maintains proper belt alignment for consistent drum rotation
• Common symptoms of failure: squealing/squeaking, belt coming off or wearing quickly, drum not turning, or burning rubber odor
• Pulley should spin freely; roughness or wobble indicates replacement is needed

• Disconnect power; if gas, also shut off gas supply before servicing
• Remove top/front panels as needed, release belt tension, and note belt routing
• Remove the old idler from its mount; transfer spring from the original if required by your model, then install the new assembly and re-route the belt
• Rotate drum by hand to verify belt tracking before reassembly and test run

This fuse holder secures a 3AB-style cartridge fuse within the appliance's electrical circuit. Replacing a cracked, loose, or heat-damaged holder restores a solid connection so the fuse can properly protect the circuit and prevent intermittent power issues.

• Provides a secure mount and reliable electrical contact for a 3AB cartridge fuse
• Helps ensure the protected circuit opens correctly during electrical faults
• Common symptoms of a failed holder: fuse won't seat, loose/burned contacts, intermittent or no power
• Direct replacement when the original holder is broken, heat-damaged, or cracked

• Disconnect power at the breaker or unplug the appliance before servicing
• Note wire positions and transfer one lead at a time to the new holder
• Install only a manufacturer-specified 3AB cartridge fuse of the correct rating
• Ensure the fuse seats firmly and all connections are tight before restoring power

The Dryness Control Board is an OEM part for GE dryers. This part monitors and regulates the drying process to detect the moisture level in the dryer drum. It adjusts the drying time and temperature accordingly, allowing your clothes to dry efficiently while preventing over-drying or under-drying.

A bad dryness control board can occur due to electrical malfunctions, damage, or wear and tear over time. If you notice symptoms such as clothes coming out damp, the dryer running for excessive periods, or error codes related to the drying process, it may be time to replace this part.

Symptoms of a bad dryness control board include:

• Clothes coming out damp
• Dryer running for excessive periods
• Error codes related to the drying process

Restore your GE dryer by replacing the faulty dryness control board with this genuine part. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This gas valve assembly regulates the flow of gas to the dryer's burner, enabling safe ignition and steady heat. Replacing a weak or failed valve restores reliable heating performance and helps clothes dry evenly. What it does:

• Opens and closes to control gas flow to the burner for proper ignition and heat.
• A failing valve can cause no heat, the burner not to light, or intermittent heating leading to long dry times.
• Helps ensure gas is shut off when not energized for safety.

• 1 gas valve assembly

• Disconnect electrical power and shut off the gas supply before servicing.
• Work in a well-ventilated area; avoid sparks or open flames.
• Transfer any model-specific fittings or brackets from the original part as directed by your service information.
• After installation, check all gas connections with an approved leak-detection solution and verify proper ignition.

The Trap Duct Assembly for Dryer is an OEM replacement part for GE dryers. It forms the internal ductwork connection between the dryer drum and the vent tube. This assembly is critical for proper airflow and efficient moisture removal during the drying cycle. 

Causes of a bad trap duct assembly can include cracks or loose connections due to heat fatigue over many cycles. Ducts must withstand temperature swings and mechanical stresses.

Symptoms of a bad trap duct assembly include:

• Increased drying times 
• Excess condensation or moisture remaining in clothes after cycles
• Visible cracks or damage to ducts

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore dryer models. 

Wrinkle care on and off switch

A replacement shield switch that helps the oven/microwave detect door position so the unit runs only when the door is closed. Restores reliable door sensing and user safety by replacing a worn or damaged switch. What it does

• Acts as the door-position sensing switch to allow operation only when the door is properly closed
• Stops intermittent or failed start issues caused by a worn or faulty door switch
• Helps correct symptoms like oven/microwave not starting, stopping mid-cycle, or inconsistent door detection
• Works as the plug-in electrical switch used in the door/shield assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Access may require removing the door or control/vent panels
• Handle small metal parts and electrical connectors carefully; avoid bending terminals
• Test door operation and proper function after installation

The Rotary Switch is an OEM part for GE dryers. This part is the control for selecting various drying cycles and settings on your dryer.

A bad rotary selector switch can occur due to wear and tear, electrical malfunctions, or physical damage. If you notice symptoms such as the switch not responding or sticking, the dryer not starting or stopping when you select a setting, or the display showing incorrect information, it may be time to replace this part.

Symptoms of a bad rotary selector switch include:

• Switch not responding or sticking
• Dryer not starting or stopping when selecting a setting
• Display showing incorrect information

Regain full control over your GE dryer's cycles by replacing the faulty rotary selector switch with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This printed backsplash graphic assembly replaces the control panel graphic on the range backguard to restore clear control markings and improve appearance. It's a direct cosmetic and labeling replacement for damaged or faded backguard graphics. What it does:

• Replaces worn, faded, cracked or peeling control markings on the range backsplash
• Restores legibility of cooktop/oven controls and indicator labels
• Preserves original layout so controls are easy to read and operate
• Cosmetic repair — does not include electronic controls or switches

• Disconnect power to the appliance before starting any work.
• Access may require removing the backguard or control console screws; handle the graphic carefully to avoid creasing or scratching.
• Verify fit and alignment before final fastening.

This replacement part is a screw, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This screw is compatible with many different areas of the appliance. Screws are generally used for keeping parts of the machinery secure and in place during use. It is possible that screws can become loose over time and need to be replaced after years of normal wear and tear.A new screw might be needed if the user notices parts of the appliances are becoming loose or are even falling off. This can be due to screws becoming stripped over time or if the appliance is bumped during transport. The repair for this part is simple. Remove the old screw and replace it with a new part. The only tools needed for this repair are a screwdriver and possibly pliers if the damaged screw is stuck in place.This screw is sold individually and is a genuine OEM replacement part sourced from the manufacturer.

Fixed buzzer that replaces the appliance's audible tone generator in the control panel, restoring beeps and alerts for cycle completion and fault signals. Simple swap that returns audible notifications used during normal operation. What it does:

• Produces the control panel's audible tones for end-of-cycle alerts and warnings.
• Replaces a buzzer that has stopped sounding or produces weak, intermittent, or distorted beeps.
• Helps restore audible error/fault notifications so you can respond to appliance alerts promptly.
• Works as the control panel's dedicated tone generator — pairs with the appliance's existing electronics.

• Disconnect power to the appliance before beginning any service to avoid electrical shock.
• Access the control panel per your model's service instructions and note wire/harness positions before removal.
• Disconnect the buzzer wiring or harness, remove mounting fasteners, and install the replacement in the same orientation.
• Reassemble panels, restore power, and run a test cycle to audible operation.