Gtd65ebsjws Parts

The Trap Duct Slides are an OEM part for GE dryers. These slides are integral to the dryer's lint trap system, providing a smooth surface for the lint screen to slide in and out easily. This ensures efficient lint trapping and removal.

Replacement of the trap duct slides may be necessary due to wear and tear, damage, or if they become clogged with lint over time. 

Symptoms of a bad Trap Duct Slides include:

• Difficulty in inserting or removing the lint screen.
• Excessive lint accumulation outside the trap area.
• Reduced drying efficiency, possibly due to restricted airflow.
• Visible wear or damage to the slides, hindering the movement of the lint screen.
• Potential for increased risk of overheating if lint is not properly trapped.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This replacement screw secures dryer panels and assemblies, helping prevent vibration and keeping components properly aligned. Use it to replace missing or stripped hardware and restore a solid, factory-tight fit during reassembly.

• Secures panels, brackets, and internal assemblies in the dryer cabinet
• Replaces lost, damaged, or stripped factory screw
• Helps reduce vibration and rattling caused by loose hardware
• Supports proper alignment of parts and a tight fit
• Symptoms can include loose or shifting panels, rattling noises, or gaps

• Disconnect power before servicing; for gas dryers, also shut off the gas supply if moving the unit.
• Match screw length and location to the original during reassembly.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Use the correct driver for your screw head style as used on your model.

The Cover Top High Depth is an OEM part for GE dryers. It is a cover for the top area of the dryer near the vent that extends deeper than a standard top cover. This cover protects internal components and provides an aesthetic covering for the dryer cabinet. 

Causes of a bad cover top high depth include normal wear and tear, impact or bending damage, or heat/exposure damage from the vent area over many heating and cooling cycles. 

Symptoms of a bad cover top high depth include:

• Excessive lint building up inside near components 
• Loose or rattling noises from the top vent area
• Visible cracks, dents, or other structural damage
• Difficulty closing or securing the dryer door or lid 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

This fuse terminal cover shields and insulates the fuse connection inside your appliance, helping prevent accidental contact and shorting. Replace a cracked or missing cover to maintain safe electrical protection and dependable circuit performance.

• Covers and insulates the fuse terminals to protect the connection
• Helps prevent accidental contact, arcing, and debris intrusion at the fuse
• Common signs you need this part: missing cover, cracks, heat discoloration, or a cover that won't stay secured
• Promotes a secure, consistent fuse connection once installed

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the fuse area per your service information; note wiring and cover orientation
• Remove the damaged cover; inspect terminals and wiring for heat damage or looseness
• Seat the new cover fully and verify it is secure and clear of wiring

This idler arm, also called a belt tensioner arm, supports the idler pulley that keeps the dryer's drive belt tight so the drum rotates smoothly. Replacing a worn arm helps eliminate noise and belt tracking issues.

• Maintains proper belt tension by positioning the idler pulley against the drive belt
• Helps prevent belt slippage, squealing, and premature belt wear
• Supports smooth, consistent drum rotation during cycles
• Typical failure symptoms include squeaking/chirping, burning rubber smell, belt coming off, or the drum not turning

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the idler assembly by removing the front or lower access panel
• Release belt tension and note the belt routing; reinstall pulley and spring as removed, then re-tension the belt
• Manually rotate the drum to verify belt tracking before reassembly and testing

The Door Assembly is an OEM component specifically designed for GE laundry machines. It includes the complete dryer door along with all necessary latching and hinge mechanisms. The door assembly provides a secure sealing entry point for loading and unloading clothes during each cycle. 

Causes of a bad door assembly can include worn out or broken hinges that cause improper closing, loose or missing latches that compromise the air seal, and cracks in the door material from hard impacts or impacts. 

Symptoms of a bad door assembly include:

• Difficulty securely closing and latching the door  
• Gaps or air leaks visible around the door perimeter
• The door not sitting properly on the dryer cabinetry
• Loud banging or rubbing noises emerging from the door area

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This ground strap assembly bonds the dryer's cabinet to the designated ground point, helping ensure safe operation. Replace a damaged or missing strap to restore a proper ground path and reduce the risk of shocks or nuisance static.

• Maintains the required electrical bond between the dryer chassis and ground as designed
• Helps prevent electric shock and reduces static by providing a low-resistance path to ground
• Replace if the original strap is loose, corroded, heat-discolored, broken, or missing
• Symptoms can include a slight tingle when touching the appliance or visible damage near the ground/terminal connection

• Disconnect power at the breaker before servicing; verify no power with a meter
• Follow your model's wiring diagram; bonding differs for 3-wire vs 4-wire cord installations per local codes
• Clean contact surfaces and secure fasteners firmly for a solid metal-to-metal bond; replace any heat-damaged hardware
• After installation, verify continuity between the cabinet and the designated ground point

This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missing.A new screw might be needed if there are areas in the appliance that seem off balance or not level. Another way to tell if a new screw is needed is if there are parts in the appliance that are loose or falling off. This is common over many years of normal use as the shaking of washers and dryers can eventually lead to loose screws. Be sure the washer or dryer is completely off before attempting to replace any screws.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with washers, dryers, and washer dryer combos made by General Electric.

This exhaust blower gasket seals the joint between the dryer's blower outlet and exhaust duct. It helps maintain proper airflow and contain lint and heat, supporting efficient drying and preventing leaks into the cabinet or laundry area. What it does:

• Seals the blower-to-exhaust connection to prevent air and lint leaks
• Helps maintain designed airflow through the drum and vent system
• Can reduce warm air or lint escaping inside the cabinet

• 1 gasket

• Disconnect power; for gas dryers, shut off gas and disconnect the supply. Allow the dryer to cool.
• Access the blower housing/exhaust duct; remove panels as needed.
• Remove the old gasket and any residue; clean mating surfaces and lint before installing.
• Seat the new gasket evenly and reassemble; avoid overtightening fasteners and ensure the home vent is clear.

This strike plate mounts at the door opening and works with the door latch/strike to keep the appliance door securely closed during operation. Replacing a worn plate helps restore positive latching and reliable cycle start/stop via the door switch.

• Provides the catch surface for the door latch/strike to engage
• Helps keep the door closed and properly aligned
• Enables the door switch to engage so the cycle can run
• Common symptoms include: door won't stay closed, door pops open, unit won't start unless the door is pressed, visible wear or bending on the plate

• Disconnect power before servicing
• Open the door and remove the screws securing the existing plate
• Align the new plate with the latch/strike and fasten securely with the existing hardware
• Test door closure and latch engagement; adjust alignment if necessary

This factory screw secures dryer panels and internal components, keeping assemblies tight and aligned so the machine operates safely and without vibration or rattling.

• Fastens sheet-metal panels, brackets, or trim to the dryer cabinet/frame
• A loose or missing screw can cause panel vibration, noise, or misalignment
• Helps restore stability after service or when original hardware is lost
• Typical symptoms include rattling, loose panels, or gaps in trim

• Unplug the dryer before servicing
• Keep track of original screw locations and lengths; replace like-for-like
• Start screws by hand to avoid cross-threading, then snug—do not overtighten
• If threads are damaged, inspect mating hole or clip before installing

This fuse holder secures a 3AB-style cartridge fuse within the appliance's electrical circuit. Replacing a cracked, loose, or heat-damaged holder restores a solid connection so the fuse can properly protect the circuit and prevent intermittent power issues.

• Provides a secure mount and reliable electrical contact for a 3AB cartridge fuse
• Helps ensure the protected circuit opens correctly during electrical faults
• Common symptoms of a failed holder: fuse won't seat, loose/burned contacts, intermittent or no power
• Direct replacement when the original holder is broken, heat-damaged, or cracked

• Disconnect power at the breaker or unplug the appliance before servicing
• Note wire positions and transfer one lead at a time to the new holder
• Install only a manufacturer-specified 3AB cartridge fuse of the correct rating
• Ensure the fuse seats firmly and all connections are tight before restoring power

The Trap Duct Assembly for Dryer is an OEM replacement part for GE dryers. It forms the internal ductwork connection between the dryer drum and the vent tube. This assembly is critical for proper airflow and efficient moisture removal during the drying cycle. 

Causes of a bad trap duct assembly can include cracks or loose connections due to heat fatigue over many cycles. Ducts must withstand temperature swings and mechanical stresses.

Symptoms of a bad trap duct assembly include:

• Increased drying times 
• Excess condensation or moisture remaining in clothes after cycles
• Visible cracks or damage to ducts

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore dryer models. 

A replacement shield switch that helps the oven/microwave detect door position so the unit runs only when the door is closed. Restores reliable door sensing and user safety by replacing a worn or damaged switch. What it does

• Acts as the door-position sensing switch to allow operation only when the door is properly closed
• Stops intermittent or failed start issues caused by a worn or faulty door switch
• Helps correct symptoms like oven/microwave not starting, stopping mid-cycle, or inconsistent door detection
• Works as the plug-in electrical switch used in the door/shield assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Access may require removing the door or control/vent panels
• Handle small metal parts and electrical connectors carefully; avoid bending terminals
• Test door operation and proper function after installation

The Control Panel is an OEM part for GE electric clothes dryers. Located at the front of the dryer, it features digital displays, touch buttons, and a wiring harness connecting all electronic functions. 

As the central command module, the control panel facilitates cycle programming and monitoring through an intuitive interface. Its surface-mounted circuit board receives input signals from buttons to direct appropriate dryer operations via output currents. Easy-to-read displays convey cycle status updates.

Symptoms of a faulty control panel include:

• Buttons not responding properly to touch selections
• LED screens improperly lighting or remaining blank
• Dryer failed to advance through the expected sequence 
• Occasional disconnected internal electrical links

Replacing with the OEM GE part restores the core command center and touch-interactive interface. Proper dryer functionality and programmability are ensured through dependable controls. Compatible with some Kenmore models.