Gts221cmarww Parts

This silicon controlled rectifier (SCR) is an electrical control component used to regulate power in appliance circuits, helping control heating and motor circuits for reliable operation. What it does:

• Acts as a semiconductor switch to control current flow in a circuit
• Enables precise switching of power to heating elements or motors
• Can prevent uncontrolled power delivery when functioning correctly
• Faulty SCRs may cause intermittent operation, no power to a circuit, or erratic heating/motor behavior

• Disconnect all power before servicing; risk of shock or damage
• Handle as an electrostatic-sensitive device; avoid touching leads or terminals directly
• Verify mounting orientation and secure all connections per appliance wiring diagrams

A replacement bottom door cap that restores the finished edge and support at the lower corner of the appliance door. Keeps the door looking complete and helps protect the hinge area from damage. What it does

• Covers and protects the bottom edge of the door for a finished appearance
• Helps shield the hinge/mount area from wear and debris
• Replaces cracked, broken, or missing bottom cap pieces
• Improves door fit and prevents snagging from a damaged trim piece

• One bottom door cap (white)

• Unplug the appliance or shut off power before starting work
• Remove any screws or retainers holding the old cap and snap the new cap into place
• Handle trim pieces gently to avoid breaking adjacent clips or tabs

This self-adhesive foam strip seals gaps and cushions components to reduce drafts, noise, and moisture intrusion—helpful for restoring proper airflow and improving efficiency where foam padding or gap sealing has deteriorated. What it does:

• Provides a soft seal to close small gaps and prevent air leaks
• Cushions panels to reduce vibration and rattling noises
• Helps limit moisture and dust entry around seals and components
• Supports consistent temperature by reducing unwanted airflow

• Clean and dry the mounting surface before applying for best adhesion.
• Trim to length with scissors or a utility knife; press firmly to set adhesive.
• Avoid stretching the foam while applying; allow adhesive to set 24 hours for full bond.
• If near electrical components, disconnect power before working and avoid covering vents.

This plastic air separator directs refrigerator airflow on the high side to help maintain even temperatures and efficient circulation. Replaces a cracked or damaged separator to restore proper airflow and compartment cooling. What it does

• Guides cold air through the appropriate ducting to help balance temperatures between compartments
• Prevents air leakage that can cause uneven cooling or warm spots
• Helps reduce frosting or humidity buildup caused by disrupted airflow
• Restores intended circulation after breakage from impact or aging

• Unplug the appliance or disconnect power before beginning any repair
• Remove shelves, drawers, or trim panels as needed to access the separator
• Handle plastic tabs and clips carefully to avoid breakage; replace any damaged fasteners

This shelf cant is the replacement cantilever-style support that secures refrigerator shelves in place, restoring stable shelf positioning and preventing shelves from tilting or sliding. Designed to fit the OEM mounting points and match original shelf alignment. What it does:

• Provides a secure support point for a refrigerator shelf so items stay level and don't shift.
• Restores proper shelf engagement when the original cant is cracked, worn, or broken.
• Helps eliminate sagging, tilting, or uneven shelves that can cause items to slide.
• Works with the existing shelf hardware and track to re-establish factory shelf stability.

• One shelf cant (exact OEM quantity: 1)

• Basic hand tools are typically required; remove stored items and the shelf before replacing.
• Align the cant with the shelf track and snap or fasten into the original mounting position per OEM alignment.
• Inspect adjacent shelf supports and tracks for wear; replace any damaged parts to ensure secure installation.
• Unplug power or follow appliance safety recommendations if working near electrical controls or lights.

This compressor overload protects the refrigerator's compressor by interrupting power when it overheats or draws excessive current. Replacing a weak or failed overload can stop repeated click/no-start symptoms and help restore normal cooling performance.

• Opens the circuit to protect the compressor during overheat or over-current conditions
• Automatically resets after cooling to prevent sustained damage
• Symptoms include: compressor won't start, rapid clicking from the compressor area, starts then stops, and a warm refrigerator/freezer
• Helps prevent motor and wiring damage caused by repeated overload events

• Disconnect power before servicing; wear appropriate PPE
• Access the rear machine compartment and remove the compressor/start device cover
• Note wire positions; pull the old overload straight off the compressor terminal and push the new one on fully seated; reconnect wiring and covers
• If the overload trips again after replacement, further diagnosis of the start relay, run capacitor, or compressor may be required

This small door handle assembly (22 in) replaces a damaged or worn refrigerator/freezer door pull to restore a secure grip and smooth opening. Fits inline with factory trim for a clean, original appearance. What it does:

• Replaces a broken, cracked or missing small door handle to restore safe gripping and door access.
• Stops wobbling or loose handles that affect door opening and closing.
• Matches factory trim finish to maintain original look and feel.

• Disconnect power and empty the door area before beginning any repair.
• Remove retaining screws or clips from the inner door panel to access the handle fasteners.
• Align handle to mounting holes, then secure with the original hardware; do not overtighten to avoid cracking.

This thimble door top is the white trim piece that covers and protects the upper edge of the appliance thimble/dryer vent opening, restoring a finished look and helping keep the seal area intact. What it does:

• Replaces a cracked, chipped or warped top trim to improve appearance and fit
• Helps keep the vent/thimble opening properly covered and aligned
• Protects the upper edge of the opening from wear and impacts
• Prevents gaps that can allow lint or debris accumulation around the opening

• Disconnect power to the appliance before beginning any repair
• Use basic hand tools; hold parts securely to avoid scratching surrounding surfaces
• Inspect mating surfaces and remove lint/debris before installing for proper fit

This is a mobility screw used to secure mobility-related components in compatible appliances, providing a reliable fastener for stable operation and correct alignment. It replaces worn or missing screws to restore secure mounting. What it does

• Fastens and secures mobility/bracket components to prevent movement or misalignment.
• Helps maintain proper alignment of moving parts that can cause noise or binding when loose.
• Commonly replaced when mounting points are stripped, damaged, or missing.
• Small replacement part that supports overall appliance stability and safe operation.

• One screw as shown/packaged by the manufacturer.

• Use the correct screwdriver or bit to avoid stripping the screw head.
• Ensure the appliance is powered off and disconnected from the power source before accessing internal components.
• Do not overtighten; snug to manufacturer torque or until the part is secure.
• If mounting hardware or threaded inserts are damaged, replace or repair those components before installing this screw.