Gts22kyncrfs Parts

The Defrost Heater Assembly is an OEM replacement part for GE refrigerators. This assembly is responsible for preventing the buildup of ice and frost on the evaporator coils by providing controlled heat during the defrost cycle. It helps prevent ice accumulation that can hinder the refrigerator's ability to cool properly.

A bad defrost heater assembly can occur due to electrical issues, component failure, or damage to the heating element. If you notice symptoms such as excessive frost or ice buildup in the freezer compartment, inconsistent cooling, or water leaking from the refrigerator, it may indicate a need to replace the defrost heater assembly.

Symptoms of a bad defrost heater assembly include:

• Excessive frost or ice buildup in the freezer compartment
• Inconsistent cooling
• Water leaking from the refrigerator

Restore your refrigerator by replacing the faulty defrost heater assembly with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This compressor start kit provides the overload protector and PTCR starting device used to help refrigerator compressors start and protect against electrical overloads. It replaces failed start components to restore reliable compressor starting. What it does:

• Supplies a PTCR (positive temperature coefficient resistor) starter to give the compressor the initial starting boost.
• Includes an overload protector that helps prevent compressor damage from electrical overload or overheating.
• Common symptom linkage: may be needed when the compressor hums but won't start, the fridge cycles without cooling, or the compressor repeatedly clicks/trips.
• Works with compressors that use separate PTCR and overload start components.

• Disconnect power to the appliance at the breaker or unplug before servicing.
• Installed at the compressor terminals; follow OEM wiring orientation and secure connections.
• Test compressor and start circuit after installation to confirm proper operation.

The Grommet Water Fill Assembly is an OEM component specifically designed for GE top-mount refrigerators. It is located at the back of the fresh food compartment and consists of the water inlet grommet that channels water from the external line.

During use, causes of failure can include mineral buildup on the filter over time inhibiting proper water flow. Deterioration of the inlet grommet seal may also occur.

Symptoms of a bad water fill assembly include:

• Slow or incomplete filling of the internal water tank  
• Leaks occurring at the rear water inlet connection point
• Mineral deposits building up within the internal waterways

This OEM GE replacement ensures a secure seal and mesh filtration for clear, contaminant-free water going to the dispenser. It maintains proper filling and is also compatible with Hotpoint, RCA, and some Kenmore models.

This genuine fastener secures appliance components such as panels and brackets. Replacing a missing or stripped screw restores proper fit and helps reduce vibration or rattling. Features 12-24 threads and an approximate 0.785-inch length. What it does:

• Fastens panels, brackets, covers, and other hardware points in the appliance
• Helps maintain proper alignment and a tight fit of components
• Replaces damaged, stripped, or missing hardware
• Common symptoms include loose or rattling parts and hardware that won't tighten

• One screw

• Disconnect power before servicing; shut off water supply if working near water components
• Start the screw by hand to avoid cross-threading; replace one-for-one in the original location
• Use the correct driver bit for the head style; tighten snugly without overtightening into plastic or thin metal

The Water Tube is an OEM replacement part for GE refrigerators. It is responsible for delivering water to the dispenser and ice maker, ensuring a steady flow of chilled water and ice cubes.

A bad water tube can occur due to wear and tear over time or damage caused by mishandling or accidents. If you notice symptoms such as water leaks, reduced water flow, or ice maker malfunctions, it may indicate a need to replace the water tube.

Symptoms of a bad water tube include:

• Water leaks or drips from the dispenser or ice maker
• Reduced water flow or weak water pressure
• Inconsistent ice production or ice cube quality

Restore your refrigerator by replacing the faulty water tube with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This 22-inch freezer glass shelf provides a flat, durable surface for organizing frozen foods and maximizing usable space. It replaces broken or missing shelves to restore stable storage and visibility inside the freezer compartment. What it does:

• Replaces a cracked, chipped, or missing freezer shelf to restore usable storage space
• Supports frozen food containers and packages with a rigid, tempered-glass surface
• Improves visibility and organization by creating a stable, flat shelf level
• Helps prevent items from falling through or collapsing between compartments

• One tempered glass freezer shelf (22 in)

• Handle carefully — tempered glass can break if dropped; wear gloves to protect hands
• Remove food and any shelf supports before installing; slide shelf into existing rails or clips
• If shelf uses plastic trim or brackets, ensure they are present and undamaged before seating the glass
• No special tools required for most installs; refer to your refrigerator's manual for model-specific guidance

The Drier is an OEM component specifically designed for GE combination refrigerator-freezers. Absorbing moisture, its treated silica particles buffer humidity within refrigerant lines. Proper drying sustains energy-efficient performance while preventing corrosion.

Causes of a faulty drier commonly relate to saturation reducing capacity. As desiccant degrades, water passes into closed system compressors requiring change. 

Symptoms of a bad drier involve:

• Frost and ice buildup impairing cooling  
• Puddling around evaporator evidencing leaks
• Higher operating costs from impaired efficiency

Causes of a bad drier involve typical saturation shortening drying cycles. Cracks release desiccant particles risking blockages necessitating timely replacement.

This OEM GE part is also compatible with some Hotpoint, RCA, and Frigidaire combination units. Replace to retain steady humidity management protecting components and maximizing freshness years of operation.
 

This replacement refrigerator door stop cushions and limits door travel to help prevent slamming and misalignment. It restores smooth, controlled door movement and helps the door stay properly positioned for reliable sealing. What it does:

• Absorbs impact and reduces door slam noise when opening or closing
• Limits door travel to prevent over-rotation that can damage the cabinet or hinge
• Helps maintain proper door alignment for an effective seal
• Commonly used when a door slams, hangs open, or rubs against the cabinet

• Unplug the appliance or disconnect power before working near electrical components
• Support the door while removing or installing the stop to prevent it from shifting
• Use appropriate hand tools; do not force or overtighten fasteners

Front control housing replaces the appliance's front control console to restore appearance and provide a secure mounting surface for the control components. It helps keep buttons, knobs, and the control board properly aligned and protected. What it does:

• Houses and supports the control board, touchpad/buttons and display so controls stay securely mounted.
• Replaces cracked, warped or damaged console sections that cause loose or misaligned buttons.
• Restores proper button and dial alignment when physical damage prevents normal operation.
• Helps reduce exposure of internal control parts to dust and splashes from normal use.

• Disconnect power (unplug appliance or switch off circuit breaker) before beginning any work.
• Removal typically requires taking off the control panel and detaching wiring—handle ribbon cables and connectors gently.
• Use the correct screwdriver and hardware; avoid overtightening screws to prevent cracking the plastic.

The GE Badge is an OEM replacement part for GE refrigerators. It is responsible for displaying the GE branding on the front exterior. Over time, the badge can become damaged from exposure and wear. Causes of a failing badge include sun damage, scrapes, and deterioration of the adhesive.

Symptoms of a bad refrigerator badge:

• Peeling edges or corners
• Discoloration or fading
• Scratches or scuffs
• The badge falling off completely

This GE badge is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement dairy door restores the small hinged compartment on the refrigerator door so butter, cheese and other small items stay organized and protected. Fits the 33" door opening on compatible GE refrigerators. What it does:

• Replaces a cracked, chipped or missing dairy door to stop items from falling out and to improve organization.
• Helps maintain a sealed compartment so cold air circulation around small dairy items is more consistent.
• Restores the hinge and latch function if the original door no longer stays closed or is loose.
• Matches OEM fit and form for easy alignment with existing door bins and hardware.

• Disconnect power to the appliance or unplug the refrigerator before starting any service.
• Remove food and door shelves/bins as needed to access mounting points.
• Use basic hand tools (screwdriver/sockets) to remove and install; retain original screws unless replacements are provided.
• Align hinge and test door closure; do not overtighten fasteners to avoid cracking the plastic.

This freezer door stop replaces the damaged or worn bumper that cushions the freezer door, helping it close smoothly and preventing damage to the door or cabinet. Color-matched Dorian Gray finish. What it does:

• Cushions door movement to reduce banging and wear
• Helps the door seal more consistently by providing proper stopping position
• Reduces noise when opening or closing the freezer door
• Restores original fit and finish for a clean, finished appearance

• Basic hand tools may be required; follow the appliance manufacturer's instructions
• Power off and empty the door area if required for safe access before installing
• Inspect surrounding trim and mounting area; replace mounting screws if worn or damaged