Gtw485asj1w5 Parts

This left-side wireform hinge secures and guides a top lid, restoring smooth opening and stable closure for affected appliances. It replaces a bent or worn hinge to reduce sagging, uneven gaps, and noisy or sticky lid movement. What it does

• Supports the lid on the left side and keeps it aligned during open/close cycles
• Restores smooth pivoting when the original hinge is bent, stretched, or broken
• Helps eliminate lid sag, uneven gaps, or rubbing against the cabinet
• Reduces rattling or binding caused by a damaged wireform hinge

• Disconnect power to the appliance before starting repairs to avoid injury
• Basic hand tools typically required; remove any trim or screws securing the old hinge
• Align the new hinge carefully and test the lid travel before fully tightening fasteners

This 6-32 machine flat-head hinge lid screw secures the lid hinge on compatible GE appliances, restoring proper lid alignment and smooth opening and closing. A simple replacement that addresses loose or rattling lids. What it does

• Fastens the lid hinge to the cabinet or hinge assembly
• Keeps the lid aligned for smooth opening and closing
• Helps stop lid wobble, rattling or uneven seating
• Replaces worn, stripped, or missing hinge screws

• One 6-32 machine flat-head hinge screw

• Turn power off and unplug appliance before servicing
• Use the correct-size screwdriver or nut driver to avoid stripping the head
• Thread screw in by hand to start, then tighten snugly—do not over-torque
• Check hinge alignment and lid operation after installation

This control board shield protects the appliance's electronic control board from debris, heat, and accidental contact to help maintain reliable operation. It's a direct-fit replacement designed to restore proper protection for the control electronics. What it does:

• Covers and shields the electronic control board from dust, moisture splash, and physical contact
• Helps reduce risk of short circuits caused by loose debris or small objects
• Preserves board components from incidental heat exposure and wear
• Commonly replaced when the old shield is cracked, broken, or missing

• One control board shield

• Disconnect power before servicing to avoid shock or damage to electronics
• Handle shield and control board carefully to avoid bending tabs or damaging connectors
• Reuse original fasteners if undamaged; replace any broken clips or screws

This hex-head machine screw secures appliance panels and internal components where a 5/16-24 x 1 inch fastener is required. Durable replacement for stripped or missing screws to restore safe assembly and reduce vibration. What it does:

• Fastens panels, brackets, and assemblies with a 5/16-24 machine thread.
• Replaces worn, stripped, or missing screws that can cause rattling or loose parts.
• Provides a secure, threaded connection for metal-to-metal or tapped-hole repairs.
• Matches OEM thread and length to maintain proper fit and alignment.

• Disconnect power and unplug the appliance before servicing.
• Use the correct hex driver or socket to avoid rounding the head.
• Thread into matching 5/16-24 tapped holes; do not force into incorrect thread sizes.
• Tighten snugly but avoid over-torquing to prevent stripping the tapped hole.

This thermistor clip secures a refrigerator/freezer temperature sensor in the correct position so the control can read accurate temperatures and keep the appliance cycling properly. Simple replacement of a damaged clip restores proper sensor placement. What it does:

• Holds the refrigerator thermistor/sensor against the evaporator tube or cabinet to ensure stable temperature readings
• Prevents the sensor from shifting or falling away, which can cause incorrect temperature control or erratic cooling
• Keeps wiring routed and protected from contact with moving or hot components
• Small, durable clip designed for a snug fit without damaging the sensor

• Disconnect power before servicing to reduce risk of shock or injury
• Handle the thermistor sensor carefully; avoid kinking or pulling the sensor leads
• Clip the sensor gently into place so it contacts the evaporator tube or designated mounting point without crushing the sensor
• After installation, restore power and verify proper temperature control and normal compressor/defrost cycles

This dual harness connector is a direct-fit replacement plug that secures two wire harnesses to restore a reliable electrical connection. It helps eliminate loose or intermittent wiring connections for affected appliance circuits. What it does:

• Provides a secure, snap-fit connection between two wire harnesses
• Restores continuity to circuits that show intermittent power, no power, or erratic operation
• Holds wiring in proper alignment to prevent accidental disconnection
• Used where a dual-wire plug mates to a control, switch, or component

• One dual harness connector

• Always disconnect power to the appliance before servicing
• Inspect wire ends and terminals for damage; replace or repair wiring if needed
• Use appropriate tools to seat the connector fully; do not force or bend terminals

This left backsplash support is the metal bracket that secures the range/oven backsplash and helps keep the control panel and rear trim stable. It restores proper alignment and reduces movement of the upper back assembly. What it does

• Provides structural support for the left side of the backsplash and control panel area
• Keeps the backsplash and rear trim aligned to prevent wobble or sagging
• Helps stop vibration or rattling coming from the upper rear of the appliance
• Replaces a bent, broken, or missing left support bracket

• One left backsplash support bracket

• Disconnect power to the appliance before starting any repair
• You may need to remove the range top, control panel, or rear access panel to access mounting screws
• Use basic hand tools; keep fasteners for reuse and note their original locations
• If you see additional damaged or missing fasteners or trim, replace them as needed for a secure fit

A molded metal support bracket that holds the right side of the oven/range backsplash assembly in place, restoring secure alignment and preventing sagging or gaps behind the control area. What it does

• Secures the right side of the backsplash or backguard assembly to the range frame.
• Helps prevent the backsplash from sagging, shifting, or coming loose when using controls or cleaning.
• Can stop visible gaps that allow debris or steam behind the control panel.
• Works with the existing backsplash components and mounting hardware to maintain proper fit.

• One right backsplash support bracket.

• Disconnect power to the appliance before attempting any service.
• Access may require removing the cooktop, control panel, or top trim.
• Use appropriate hand tools; keep track of fasteners and any clips removed.
• If the backsplash or adjacent parts are damaged, inspect related fasteners and supports for wear before reassembly.