Gud27essm/27Gssm Parts

Size: 8 - 18 ab.

This tub kit replaces worn or damaged hub components and the agitator to restore proper washer operation and reduce noise or wobble. Designed to fit compatible GE top-load washing machines, it helps secure the agitator to the tub assembly. What it does:

• Replaces the hub nut that secures the agitator to the transmission/tub shaft
• Provides washers that ensure a tight, vibration-resistant seal and alignment
• Includes a replacement agitator to restore proper clothes movement and cleaning action
• Addresses symptoms like excessive noise, shaking, or a loose/rocking agitator during cycles

• Disconnect power and water supply before beginning any repair
• Follow OEM instructions for torque and part orientation; use proper tools to avoid damage
• Inspect surrounding parts (agitator dogs, drive shaft, seal) and replace if worn

This main wiring harness connects the dryer's internal components to route power and signals, restoring proper electrical continuity so controls and motors can operate reliably. What it does

• Carries power and signal connections between the control, motor, heating assembly, and sensors
• Replaces damaged or burned wiring that can cause intermittent operation or no power to drive components
• Helps resolve symptoms like no spin, no heat (when related to wiring), or tripped fuses/thermal cutouts due to shorted leads
• Designed to match OEM terminal and connector locations for straightforward replacement

• One main wiring harness assembly

• Disconnect power at the breaker before starting any repair; this part handles live electrical connections
• Verify connectors match your dryer model and route the harness exactly as removed to avoid chafing or heat exposure
• Inspect connectors, terminals, and nearby insulation for additional damage; replace other components as needed

This UI harness assembly connects the appliance control console to the main control board, restoring signal and power pathways for the user interface. Use it to replace a damaged or disconnected control wiring harness. What it does:

• Transfers power and control signals between the console/touchpad and the main control board
• Re-establishes display, keypad response, and electronic control communication
• Commonly replaced when the control is unresponsive, display is blank, or buttons don't register
• Helps resolve intermittent operation caused by damaged wires or loose connectors

• One UI harness assembly as shown

• Disconnect power to the appliance before starting any repair
• Handle connectors gently and match keyed plugs; do not force connections
• Route the harness following the original path and secure with existing clips

This communication harness provides an RJ45 connection between appliance control modules to enable board-to-board data signals and diagnostics. It restores proper communication so control boards can exchange status and commands. What it does:

• Carries digital communication signals between control boards using an RJ45-style connector
• Helps resolve issues where control modules fail to communicate or show communication errors
• Used when damaged, corroded, or broken connector wires cause intermittent or no signal
• Maintains correct pin alignment for reliable data transfer

• Disconnect power to the appliance before starting any work to avoid electrical shock
• Handle connectors by the housing; avoid pulling on wires to prevent damage
• Route the harness away from sharp edges, heat sources, and moving parts to prevent wear

This control support is the mounting bracket that secures the appliance control assembly, keeping the control panel stable and aligned for reliable operation. Replaces a worn or broken support to restore proper panel fit and reduce vibration. What it does:

• Holds the control board/panel in place to prevent sagging or misalignment
• Keeps control knobs and buttons properly positioned for accurate use
• Reduces vibration and rattling that can affect button/knob response
• Can prevent intermittent contact caused by a loose or damaged support

• One control support bracket

• Disconnect power (unplug the appliance or shut off the breaker) before starting any work
• Access usually requires removing the control panel or back panel; keep fasteners organized
• Install with original mounting screws; inspect surrounding clips and hardware for wear

This main wiring harness connects the washer's control console to the machine's electrical components, enabling reliable power and signal transmission for normal operation. Replaces a worn or damaged harness to restore electrical connectivity. What it does

• Transfers power and control signals between the washer control board and major components.
• Restores intermittent or lost functions caused by broken, burned, or corroded wiring.
• Helps resolve issues such as no-start, unresponsive controls, or erratic cycle behavior when wiring is the cause.

• 1 main wiring harness with JST-style connector(s).

• Disconnect the washer from power before starting any repair.
• Match connector shapes and wire colors; do not force connectors into place.
• Route the harness along original clips and channels to avoid pinching or heat exposure.

This screw is a factory replacement fastener used to secure appliance panels and components. It restores lost or loose hardware so parts sit correctly and operate without rattling or movement. What it does

• Secures panels, brackets, and small components to the appliance frame
• Restores proper alignment and helps eliminate rattling or vibration
• Replaces missing or stripped fasteners that prevent parts from staying fixed
• Matches OEM fit for reliable fastening where the original screw was used

• One replacement screw

• Use the correct-size screwdriver or driver bit to avoid stripping the head
• Power off and unplug the appliance before accessing internal components
• Tighten snugly but avoid overtightening to prevent thread damage
• Keep removed hardware organized so you can install replacements in the original locations

A replacement pin alignment used to correctly position and secure moving parts in appliance hinge or latch assemblies. Restores proper alignment to reduce sagging, rubbing, or uneven operation for smoother, quieter performance. What it does:

• Aligns and secures hinge or latch components to maintain correct movement and fit
• Helps stop door sag, binding, or uneven closing when the alignment pin is worn or damaged
• Reduces rubbing and noise caused by misaligned parts
• Restores proper clearance for seals and moving assemblies

• One pin alignment

• Refer to the appliance OEM service manual for model-specific removal and installation steps
• Disconnect power (or unplug) and, if applicable, remove stored contents before working on doors or hinges
• Use basic hand tools; avoid forcing parts or over-tightening fasteners to prevent damage
• If alignment issues persist after replacement, inspect associated hinges, brackets, and fasteners for wear

This 1/4-20 Taptite hex washer-head screw secures panels and internal components in your appliance. Its thread-forming design creates a tight, vibration-resistant hold in untapped metal to keep assemblies aligned when a fastener is missing or stripped.

• Fastens brackets, panels, and hardware to the cabinet/frame
• Taptite design forms threads in pre-punched, untapped holes for a secure fit
• Replaces missing, stripped, or rusted screws
• Helps reduce vibration and rattling from loose mounts

• Unplug the appliance; if servicing a washer, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the appropriate nut driver or socket until snug—do not overtighten

This is a hex pan thread screw used to secure appliance panels and components. It replaces missing or damaged fasteners to restore proper fit and reduce vibration or rattling. What it does

• Secures panels, brackets, or components to the appliance frame
• Restores tight fit where a worn or missing screw caused loose panels or rattling
• Provides a hex head drive for easy tightening with the correct socket or bit
• Matches OEM fastening points when replacing the original screw

• One hex pan thread screw

• Use the correct hex socket or driver to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or damage components
• Disconnect power or follow appliance safety procedures before servicing
• Keep removed hardware organized to confirm correct replacement

This bracket connector is a small metal mounting bracket that secures wiring or components inside the appliance, restoring stable alignment and connection points. It helps stop loose wires or parts from shifting and reduces intermittent electrical contact. What it does

• Provides a secure anchor point for wiring harnesses or small components
• Prevents strain on electrical connections that can cause intermittent operation
• Keeps internal parts aligned to reduce rattle and wear
• Replaces a damaged or missing mounting bracket to restore factory fit

• Inspect surrounding wiring and fasteners; replace any damaged clips or screws.
• Secure bracket with the original screws or the correct-size fasteners; do not overtighten.
• Disconnect power before accessing internal components to avoid shock or injury.

The Mode Shifter Assembly is an OEM part for GE washer/dryer units. This part is responsible for shifting between different modes such as washing, spinning, and drying. The mode shifter ensures smooth and accurate shifting, allowing for seamless transitions between the various modes of your GE washer/dryer. It engages and disengages the mode shifter mechanism, ensuring that the appropriate functions are activated at the right times.

A bad mode shifter actuator can occur due to wear and tear, mechanical failure, or electrical issues. If you notice symptoms such as the washer/dryer not shifting modes properly, unusual noises during operation, or error codes indicating a faulty actuator, it may be time to replace the component.

Symptoms of a bad mode shifter actuator include:

• Improper shifting between modes
• Unusual noises during operation
• Error codes indicating a faulty actuator

Restore the smooth operation of your GE washer/dryer by replacing the faulty mode shifter actuator with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Rod Assembly is an OEM replacement part for GE washing machines. Measuring 27 inches it is responsible for guiding the movement of the inner drum during the cycles while cushioning vibration and impact. The suspension rod assembly works together with other suspension components to absorb shock and minimize noise.

Symptoms of a bad suspension rod assembly include:

• Excessive shaking, vibrating, or rattling during operation
• Noisy operation
• Premature wear of other components

Causes of failure can be normal wear and tear over long-term use. Heavy loads, off-balance loading, or other machine misuse can exacerbate issues by placing undue stress on suspension elements.

This GE OEM part is also compatible with Hotpoint, RCA and select Kenmore models for easy replacement.

This control knob assembly restores a solid, easy-to-grip selector on your appliance's console so you can accurately choose cycles and settings. It replaces broken or stripped knobs that slip, wobble, or fall off the control shaft.

• Attaches to the control/timer shaft so you can turn and set functions
• Replaces cracked, missing, or hub-stripped knobs
• Helps resolve free-spinning knobs or knobs that won't stay on
• Maintains correct shaft engagement and a clean, finished console appearance

• Disconnect power before servicing
• Pull the old knob straight off; avoid prying against the console
• Align the new knob with the flat/splined shaft and press until fully seated
• Inspect the shaft for wear or damage before forcing