Gud27gssjoww Parts

This replacement drum assembly is the rotating cylinder that tumbles laundry in your dryer. Replacing a damaged or out-of-round drum restores smooth, quiet tumbling and helps protect fabrics from snags, scraping, and uneven drying.

• Forms the rotating chamber that holds clothes; driven by the belt and motor to tumble items for drying
• Works with drum seals and lifters/baffles to maintain airflow and separate fabrics for even drying
• Replacing a dented, cracked, or out-of-round drum can resolve thumping, scraping, or rumbling noises
• Addresses sharp seams, loose spots, or rust that can snag/tear clothing or leave marks

• Disconnect power; shut off gas supply for gas models before service
• Remove top/front panels and release belt tension to lift out the old drum; note belt routing
• Compare parts and move over any reusable, model-specific components if required
• Inspect belt, idler pulley, bearings, and felt seals while open; replace if worn

The Gearcase is an OEM part for GE washing machines. This gearcase houses the transmission components that transfer power from the washer motor to the inner tub and agitator or impeller. 

Causes of a bad gearcase often include worn gears that strip or fail to engage properly over time, stripping or damage to internal sleeves/bushings, or accumulation of debris that prevents smooth operation. 

Symptoms of a failed gearcase include:

• The agitator or inner tub not spinning as intended
• Loud grinding noises coming from within the unit    
• Transmission issues like the inability to switch cycles
• Overflow error codes or motor running errors  

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This safety thermostat is a temperature-sensitive cutoff for gas dryers. It monitors heat at the burner housing and opens the circuit if temperatures rise too high, helping protect the appliance and restore safe, reliable heating performance.

• Monitors burner/heater housing temperature to prevent overheating
• Opens the heat circuit when an over-temperature condition occurs
• Common symptoms: no heat, burner won't ignite or stay lit, heat shuts off too soon, long dry times
• Overheating or failure is often caused by restricted airflow; check venting and lint buildup

• Disconnect power and shut off gas supply before servicing
• Access the thermostat on the burner/heater housing; transfer wires one at a time and mount flush using the original hardware
• Do not overtighten; ensure firm metal-to-metal contact for accurate sensing
• After repair, clear lint and verify strong airflow at the exterior vent to prevent repeat issues

This exhaust gasket seals the dryer's exhaust duct connection to contain airflow and keep lint out of the cabinet. A tight seal helps maintain drying performance and efficiency while reducing warm, moist air leakage behind the unit.

• Seals the joint between the exhaust duct and outlet/blower housing to prevent air and lint leaks
• Helps maintain proper airflow for consistent drying results
• Wear or damage can cause longer dry times and warm, humid air or lint behind the dryer
• Visible tears, flattening, or missing sections indicate the gasket should be replaced

• Disconnect power; turn off gas supply for gas models before servicing
• Pull the dryer forward, disconnect the vent, and remove panel(s) as needed to access the exhaust connection
• Remove the old gasket and residue; clean mating surfaces; seat the new gasket evenly
• Reassemble, reconnect the vent, ensure the external vent is clear, and check for air leaks

The Baffle is an OEM part for GE electric dryers. Located inside the dryer drum, it helps separate clothes and improves air circulation during tumbling cycles. 

To achieve consistent drying times, a dryer relies on balanced airflow penetrating all areas where clothes reside. The baffle creates divisions to ensure air fully surrounds each layer instead of bypassing some areas. Its raised ridges also help tumbling action by preventing clumps of clothes.

Symptoms of a bad baffle include:

• Slow, uneven drying requiring extra cycles  
• Certain areas of clothes remain damp while others over-dry
• Reduced airflow output from the vent due to blockage

Replacing it with the genuine GE baffle plate restores optimized air distribution within the drum. The part is also compatible with some Kenmore dryers that use GE elements.

This retaining clamp secures wiring, hoses, or small assemblies to keep them routed and stable, helping prevent rubbing and vibration that can lead to wear or intermittent issues. Use it to replace a broken or missing clamp. What it does:

• Holds wires, hoses, or tubing in place to prevent contact with moving parts
• Reduces vibration and rattling by keeping components secure
• Prevents chafing that can cause insulation wear or exposed wiring
• Restores proper routing after repairs or part replacement

• Disconnect power (and water if applicable) before accessing internal components
• Use appropriate hand tools; avoid over-tightening which can damage the clamp or secured part
• Inspect surrounding wiring/hoses for damage and replace if needed

This clamp is a small retaining fastener used to secure hoses, tubes or wiring to appliance fittings and keep connections stable during operation. It helps prevent leaks, chafing and loose connections that can cause performance issues. What it does:

• Secures a hose or tube to a barb or fitting to maintain a tight seal
• Prevents hoses and lines from slipping free during use or vibration
• Reduces wear from rubbing or chafing by holding components in place
• Helps stop minor leaks at hose junctions when properly seated

• One clamp (quantity: 1)

• Disconnect power and water supply before servicing the appliance
• Drain or catch any residual water from hoses before removing the old clamp
• Use the correct pliers or screwdriver for the clamp type; avoid over-tightening which can damage hoses
• Inspect adjacent hoses and fittings and replace any worn components while accessible

This lid bumper cushions the lid of your top-load washer as it closes, absorbing impact to reduce slamming noise and protect the top panel's finish. Replace a worn or missing bumper to restore smooth, quiet lid operation. What it does

• Absorbs impact between the lid and cabinet to reduce slamming and vibration noise
• Helps protect the top panel finish from chips and scratches near the lid area
• Restores proper cushioning when the original bumper is missing, cracked, or flattened
• Common symptoms: lid slams or clunks when closing, increased noise, visible missing bumper

• 1 lid bumper

• Disconnect power before servicing
• Open the lid and pull the old bumper straight out of its mounting hole; needle-nose pliers can help if it's stuck
• Clean the hole and surrounding surface for a secure fit
• Press the new bumper fully into the hole until seated flush; for even cushioning, consider replacing both if your model uses two

This front panel assembly replaces a damaged or worn control-panel face to restore the appliance's front appearance and provide a secure mounting surface for controls. It keeps the control area sealed and looking factory-fresh. What it does:

• Replaces the visible front/control panel to cover and protect underlying controls and electronics
• Provides a mounting surface for buttons, knobs, or the touch-control interface
• Helps prevent dirt, grease, and moisture from reaching internal components
• Common repair for cracked, discolored, or broken control-face panels

• One front panel assembly as shown

• Installation requires removing the range/oven console and disconnecting power first — disconnect power at the breaker or unplug the appliance
• Handle panels and clips carefully to avoid damaging trim tabs or painted surfaces
• Use proper fasteners and alignment during reassembly; verify controls and display function before returning the appliance to service
• Label connections and take photos for reference

This right-hand hinge washer cover protects and conceals the hinge area on the washer lid, restoring a finished appearance and preventing dirt or moisture from contacting the hinge assembly. What it does:

• Covers the right-side hinge/washer area to keep debris and moisture out of the hinge assembly
• Helps maintain proper lid alignment and reduces exposed sharp edges
• Restores the washer's cosmetic finish after damage or wear
• Can eliminate rattling or rubbing caused by a missing or broken cover

• One right-hand hinge washer cover

• Disconnect power to the appliance before starting any repair
• Remove the washer lid or access panel per the manufacturer's instructions to reach the hinge area
• Fasten the cover using the original screws/clips; do not force or overtighten plastic tabs
• If other hinge components are damaged or loose, inspect and replace as needed for a safe repair

This stop-drain hose routes and drains water from the appliance to the drain or pump, helping prevent standing water and improper drainage. Replaces a worn, cracked, or leaking drain hose to restore proper water flow. What it does

• Channels discharged water from the appliance to the drain/pump assembly.
• Stops leaks caused by split, brittle, or collapsed hose sections.
• Helps restore normal draining when water pools in the tub or cabinet.
• Reduces the chance of water damage from a failed hose connection.

• Disconnect power and shut off the water supply before beginning any work.
• Remove old hose and inspect fittings; replace clamps if corroded or damaged.
• Route hose without sharp bends or kinks and secure with the factory clamps or equivalent.
• After installation, run a short cycle and check all connections for leaks.

This duct exhaust directs and channels appliance exhaust air to the venting system to help remove heat, steam and odors from the unit. Fits into the appliance's vent path to restore proper airflow and venting performance. What it does:

• Channels exhaust air from the appliance to the household venting system
• Restores a sealed outlet path to reduce backflow and poor venting
• Helps prevent overheating and moisture buildup in the appliance cabinet area
• Commonly replaced when the existing duct is cracked, warped or missing

• Disconnect power and gas (if applicable) before servicing; follow manufacturer safety instructions
• Verify orientation and seating into the appliance vent before tightening fasteners
• Use proper venting materials and clamps when reconnecting to the home vent system

This is a replacement 8-18 threaded hex-washer-head screw (3/8" length, zinc finish) used to secure panels and components on compatible appliances. It restores proper fit and stops rattling or loose parts. What it does

• Fastens panels, brackets, or assemblies where an 8-18 threaded screw is specified
• Replaces missing or damaged screws that cause loose panels or vibration
• Restores secure mounting for trim, brackets, or internal components
• Matches OEM head style and finish for correct fit and appearance

• One replacement screw (8-18 x 3/8", hex washer head, zinc)

• Disconnect power and water before starting any repair
• Use the correct driver or bit to avoid stripping the head
• Do not overtighten; snug to secure components without deforming parts
• If other fasteners are damaged, replace them with identical OEM parts

This overflow elbow is a small drain fitting that routes excess water away from the appliance to prevent spills and water damage. It restores proper overflow/drain flow so the unit can safely divert unwanted water. What it does:

• Directs overflow or drain water from the appliance plumbing to the drain path
• Replaces cracked, clogged, or leaking elbows that can cause pooling or leaks
• Helps restore normal draining behavior and reduces risk of water where it shouldn't be
• Fits into the appliance's existing drain/overflow tubing and connections

• One overflow elbow

• Inspect surrounding hoses and clips; replace any damaged components for a reliable repair
• Disconnect power and water supply before beginning work to avoid electrical shock or flooding
• Use appropriate clamps or fittings to ensure a secure, leak-free connection

A hinge bushing that helps the appliance door pivot smoothly and maintain proper alignment. Replacing a worn bushing restores stable door operation and reduces sticking, noise, and uneven closing. What it does:

• Provides a low-friction pivot surface for a door hinge
• Keeps the door aligned to prevent sagging or gaps when closed
• Reduces squeaks, binding, and irregular movement at the hinge
• Helps extend hinge and door hardware life by minimizing metal-on-metal wear

• One hinge bushing

• Disconnect power and remove or support the door before working on hinges
• Inspect hinge and surrounding hardware; replace any damaged components to ensure proper fit
• Install with correct orientation; do not force parts—misalignment can cause premature wear
• Use basic hand tools; follow OEM service instructions if available