Gud27gssjoww Parts

This factory service kit is engineered for the 27-inch Centauro front-load washer platform. It refreshes critical tub and basket components to help restore smooth, quiet spinning and consistent wash performance.

• Maintains proper drum rotation, alignment, and sealing within the tub/basket system
• Helps address rumbling or grinding during spin, excessive vibration/wobble, or water near the tub area
• Restores a secure fit between rotating and stationary tub components
• Platform-specific fit for correct clearances and balanced operation

• Disconnect power and water before servicing; wear gloves and eye protection
• Access typically requires removing top/front panels and door boot; support the tub and drum during disassembly
• Transfer and torque fasteners evenly per service instructions; re-level the washer after reassembly
• Run a test rinse/spin and check for noise and leaks before returning to service

The agitator screw secures the washer's agitator to the drive shaft so it can move clothes effectively during the wash cycle. Replace a lost, stripped, or rusted screw to help stop wobble and restore proper agitation.

• Fastens the agitator to the drive shaft/coupler to transfer motion
• Address a loose or wobbly agitator, rattling/clunking, or weak/intermittent agitation
• Replace if the original screw is missing, corroded, or has stripped threads or head
• Helps prevent the agitator from lifting off during operation

• Disconnect power and ensure the washer is empty before servicing
• Remove the fabric softener dispenser and agitator cap to access the fastener
• Align parts, start the screw by hand to avoid cross-threading, then tighten snugly—do not overtighten
• Reinstall caps/dispenser and run a brief test cycle to proper agitation

This suspension rod support socket replaces the plastic cup the suspension rod sits in on a top-load washer. Replacing a worn socket restores smoother tub movement and helps reduce vibration and noise during wash and spin cycles.

• Supports the suspension rod at the tub/frame connection point
• Provides a low-friction pivot to stabilize the basket
• Helps reduce excessive shaking and out-of-balance banging
• Common signs of failure: cracks, squeaks/scraping, or the rod popping out

• Unplug the washer and shut off water supply before servicing
• Access the suspension area per your model (remove top/front panel as needed)
• Support the tub, relieve tension on the suspension rod, swap the socket, and ensure the rod seats fully in the new socket
• Reassemble, level the washer, and run a test spin to check balance

This part is the outer tub assembly for washing machines. It is often used in washer dryer combo units. This particular part houses the spin basket. It also holds the water during the washing cycles. In the event that the washing machine is leaking water, do a visual inspection of the outer tub to check for any cracks. If the tub has been damaged in any way, it will allow water to leak out. If this is the case, it will need to be replaced with this durable part. Make sure to unplug the washing machine from the outlet prior to attempting to replace this part. Wear work gloves to protect the hands.The tub is compatible with washing machines and washer dryer combo units that are manufactured by GE and Kenmore. It is a genuine OEM part this is sourced directly from the manufacturer. It is sold individually.

This pulley nut secures the washing machine's drive pulley to its shaft, helping keep the belt aligned so the basket can agitate and spin smoothly. Replacing a worn or missing nut helps prevent pulley wobble and belt issues. What it does:

• Fastens the drive pulley securely to the shaft
• Helps maintain proper belt tracking and drive engagement
• A loose, stripped, or missing nut may cause rattling or scraping noises, belt slippage or the belt coming off, and intermittent or no spin/agitation

• One pulley nut

• Disconnect power and water; wear appropriate PPE
• Access the drive pulley from the rear or bottom per the service instructions
• Support the pulley while loosening/tightening the nut to avoid stressing the shaft
• Pulley seating and belt alignment before reassembly and test run

This motor strap secures the appliance motor to the cabinet, keeping the motor stable during operation to reduce vibration and noise. Use this replacement to restore proper motor positioning and support in compatible models. What it does:

• Holds the motor firmly in place to prevent movement or shifting during use
• Helps reduce vibration and associated noise caused by a loose motor
• Maintains correct motor alignment so belts and linkages run smoothly
• Commonly used when a worn or broken strap allows motor sag or misalignment

• One motor mounting/retaining strap

• Disconnect power to the appliance before beginning any work
• Inspect mounting points and fasteners; replace any damaged hardware as needed
• Secure strap to the motor and cabinet using the original mounting holes and recommended hardware

This is a genuine GE replacement screw used to secure appliance panels and components, restoring proper fit and reducing vibration or rattling. A simple fastener that helps keep assemblies aligned and functioning safely. What it does:

• Secures panels, brackets, and small components in place
• Prevents noise from loose parts and maintains structural alignment
• Restores proper fastening after repairs or wear
• Matches OEM fit for reliable replacement

• Disconnect power to the appliance before accessing internal parts
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread carefully and tighten until snug; do not overtighten to prevent damage
• Replace any damaged or missing fasteners with the same OEM part for best results

This 5/16-18 hex screw secures appliance panels and components with a common coarse thread. Durable fastening for repairs where the original hex screw has stripped, broken, or gone missing — restores proper fit and alignment. What it does:

• Fastens panels, brackets, and assemblies that use a 5/16-18 hex fastener
• Replaces missing or damaged screws that cause loose or rattling parts
• Helps re-establish secure mechanical connections after disassembly
• Matches OEM thread form and head style for correct seating and torque

• Use the correct hex socket or wrench to avoid rounding the head
• Tighten to secure fit; avoid over-torquing which can strip threads or damage parts
• Check mating threads for damage before installation; replace if worn
• Handle sharp threads carefully and wear gloves if needed

This small mounting screw secures panels and trim on compatible GE appliances, restoring a solid, vibration-free fit. Use it to replace a missing, stripped, or damaged fastener and keep parts aligned and secure. What it does:

• Fastens panels, trim, or small components to the appliance frame
• Replaces missing or damaged screws that cause loose or rattling parts
• Restores secure attachment when threads are stripped or worn
• Helps maintain proper alignment to prevent noise and component wear

• Use the correct screwdriver size to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power or move the appliance to a safe position when accessing internal panels
• Consider a replacement clip or insert as recommended by the manufacturer

The Grommet is an OEM part for GE washing machines. Found around openings or connection points, it provides a resilient seal to prevent vibration noises and water entry.

Causes of a bad grommet include cracks, tears, or compression from extended use that eliminates the noise-dampening function. 

Symptoms of a bad grommet include:

• Loud buzzing or knocking sounds heard through walls/cabinet during use  
• Water stains or damage detected inside the washer's surrounding areas
• Gaps visible where the grommet no longer properly seals an opening

This OEM GE replacement grommet is also compatible with some Hotpoint, RCA, and Kenmore models. Prevent noise complaints and leaks by relying on quality grommets. Replace yours today for smoother operation and protection against water damage.

This motor support is the stamped metal bracket that secures the dryer motor and blower assembly, keeping components aligned for smooth operation. It restores proper motor mounting and reduces noise from loose or misaligned parts. What it does:

• Holds the dryer motor and blower housing in the correct position to prevent wobble or misalignment
• Helps maintain proper blower alignment for effective air movement
• Supports safe, reliable motor operation when the original bracket is bent, cracked, or worn

• Disconnect power (unplug electric or shut off gas and breaker) before beginning repair
• Access requires opening the dryer cabinet and removing the drum and/or front panel on many models
• Inspect related components (motor mounts, blower wheel, idler, belt) and replace if damaged

A push-on speed nut that secures panels, trim, or lightweight components to studs and shafts, restoring a tight, rattle-free fit. Ideal when the original retaining nut is damaged or missing. What it does

• Climbs and locks onto a threaded stud or shaft to hold panels and assemblies in place
• Prevents loosening and vibration that can cause rattles or misalignment
• Common replacement when the original nut is stripped, cracked, or no longer grips

• Disconnect power and water (if applicable) before servicing the appliance
• Press the nut firmly onto the stud or shaft until fully seated; use pliers for tight fits if needed
• Replace any damaged mating hardware for a secure repair