Gxsf39e Parts

The GE clip is an OEM replacement part responsible for securely holding the water filter in place within the appliance. Its primary function is to ensure a tight and stable fit of the water filter, preventing any potential leaks or misalignments during the appliance's operation. 

Common causes of a bad clip can include regular wear and tear, accidental impact, or corrosion.

This part fixes the following symptoms:

• The water filter not staying in place or coming loose
• Leaks or drips around the water filter area
• Difficulty in inserting or removing the water filter
• Reduced water flow or dispensing issues from the appliance
• Visible damage or wear to the clip

The GE clip can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This O-ring creates a tight, leak-resistant seal between mating water system components. Replacing a worn seal helps stop drips and maintain correct pressure and flow in your GE water treatment system.

• Forms the compression seal between housings, manifolds, or valve fittings
• Helps prevent water leaks and seepage at the connection
• Maintains system pressure by reducing bypass at the joint
• Typical failure signs: flattening, cracks, nicks, swelling, or persistent drips even after tightening

• Shut off the water supply and relieve system pressure before service
• Clean the groove and mating surfaces; remove debris, scale, or old residue
• Lightly lubricate with food-grade silicone grease; do not use petroleum-based products
• Seat the O-ring evenly without twisting and tighten fittings to manufacturer guidance—do not overtighten

Keep leaks at bay. This O-ring Seal Kit restores the watertight connections in your water softener's control and bypass assemblies, helping stop drips and maintain proper system pressure after age, wear, or servicing.

• Maintains a tight, leak-free seal at control valve, bypass, and plumbing connection points
• Replaces flattened, cracked, or nicked O-rings that can cause seepage or drips
• Helps preserve system pressure and prevent standing water or corrosion inside the cabinet
• Useful after valve/head service when original seals no longer seat properly

• Unplug the unit, shut off the water supply, and place the softener in bypass to relieve pressure
• Open a nearby cold-water faucet to depressurize; have towels ready
• Clean grooves and mating surfaces; install new O-rings lightly coated with food-grade silicone lubricant (avoid petroleum-based products)
• Reassemble, restore water slowly, and check all joints for leaks

This bypass valve assembly installs on the water softener head and allows you to route household water around the softener for maintenance or emergencies. A worn valve may leak or bind; replacing it restores reliable switching between service and bypass.

• Directs water either through the softener or around it for service
• Lets you isolate the softener during maintenance or troubleshooting
• Common symptoms: leaks at the bypass, handle hard to turn or stripped, unit stuck in bypass, unexpected hard water
• Helps maintain proper flow and makes service/bypass selection consistent

• Unplug the softener and shut off the water supply; open a nearby faucet to relieve pressure
• Note port orientation; transfer any seals/clips from the old assembly if applicable
• Lightly lubricate O-rings with silicone-based grease during reassembly
• Restore water and power, then check for leaks and proper service/bypass operation

Screen cone is a replacement cone-shaped screen that helps keep lint and debris out of the appliance's drain and pump area, reducing clogs and helping protect pump components from wear. What it does:

• Traps lint and loose debris before it reaches the drain and pump assembly.
• Helps maintain proper draining and reduces the chance of recurring clogs.
• Reduces stress and potential damage to the pump impeller caused by foreign debris.
• When worn or missing, common symptoms include slowed draining, recurring clogs, or unusual pump noise.

• Disconnect power to the appliance (unplug or shut off breaker) before accessing the pump/drain area.
• Turn off water supply if required by your model and drain remaining water before removal.
• Replace the old screen cone with the new unit, ensuring it seats fully in the housing; no special tools are typically required.

This brine valve assembly is the replacement valve used in compatible GE integrated water/softener systems to control brine flow during regeneration cycles. Restores proper brine delivery so the system can clean and recharge resin for consistent water quality. What it does

• Directs brine solution flow during the softener regeneration cycle to flush and recharge the resin bed.
• Ensures correct timing and sealing of brine flow to prevent incomplete regeneration.
• Commonly replaces a failed or leaking valve to stop brine leaks or regeneration issues.
• May help address symptoms such as weak softening performance, visible leaks, or frequent/noisy regeneration cycles.

• One brine valve assembly

• Disconnect power and shut off water supply before servicing; follow all safety precautions.
• Replace only with the exact part number to ensure fit and function.
• Inspect nearby fittings and tubing for wear and replace if damaged; check for leaks after installation.

This O-ring seal is a small rubber gasket that helps form a tight, leak-resistant connection in compatible appliance assemblies. It prevents water or air leaks and maintains proper sealing where two components meet. What it does:

• Seals joints and fittings to prevent water or air from escaping.
• Restores a reliable seal on pumps, valves, or hose connections.
• Commonly used when leaks or pressure loss occur at a connection point.
• Helps maintain appliance performance by preventing fluid intrusion.

• Inspect mating surfaces and grooves for damage or debris before installing the new O-ring.
• Lubricate the O-ring lightly with a manufacturer-recommended lubricant (or water for some water seals) to ease installation and prevent twisting.
• Replace any damaged fittings or housings that could cut or pinch the new O-ring.
• Unplug the appliance and shut off water and power sources when accessing internal components.

This nut ferrule is a small compression fitting that secures the refrigerator water line connection to prevent leaks and keep the dispenser/ice maker supplied. It's a direct-replacement hardware piece used where the water tubing meets the inlet fitting. What it does:

• Secures the water tubing to the inlet fitting using a compression seal
• Helps prevent leaks at the water-line connection
• Restores a loose or damaged compression fitting connection
• Commonly replaced when the water line leaks or won't seat properly

• One nut ferrule compression fitting

• Turn off the appliance water supply before replacing the fitting
• Remove the old nut/ferrule and slide the new ferrule onto the tubing, then thread the nut onto the inlet fitting
• Tighten by hand first, then snug with an appropriate wrench; avoid over-tightening to prevent damage
• After installation, turn the water back on and check the connection for leaks

A small rubber O-ring that seals a water or fluid connection to prevent leaks and keep appliance lines watertight. Simple replacement restores a reliable seal at the mating fitting. What it does

• Creates a watertight seal at pipe, hose, or valve connections to stop drips and leaks
• Helps maintain proper pressure by preventing fluid bypass at the joint
• Commonly used where a compact ring seal is required between metal or plastic fittings
• Can resolve symptoms such as visible leaking, puddling under the appliance, or intermittent drips at a connection

• One O-ring seal (1/4 in. x 3/8 in.)

• Turn off and disconnect water supply and power to the appliance before servicing
• Remove the old O-ring, inspect mating surfaces for nicks or debris, and clean before seating the new ring
• Lightly lubricate with a water-safe (food-grade) silicone lubricant if needed for installation; avoid petroleum-based products
• Ensure the O-ring sits evenly in the groove and is not twisted or overstretched during installation

This rubber O-ring seal creates a watertight connection at a pump or hose junction to help prevent leaks and keep the appliance running normally. Fits into a groove to compress and block water passages. What it does:

• Seals pump, hose or plumbing connections to prevent water leaks at joints
• Helps maintain correct pressure and flow at the sealed connection
• Commonly replaced when you see leaks, puddling under the appliance, or dripping near the pump area
• Small part that restores a secure seal after service or when the old ring is worn or damaged

• Disconnect power and shut off the water supply before servicing the appliance
• Drain remaining water from hoses or the pump housing to avoid spills
• Inspect mating surfaces for nicks or debris and replace if damaged for a proper seal
• Lubricate lightly with water or a manufacturer-recommended lubricant to aid installation

This replacement screw, sized #10-14 x 2 in, secures appliance panels, brackets, and hardware. It restores a tight, reliable hold when an original fastener is missing, stripped, or corroded, helping prevent looseness, vibration, and misalignment.

• Fastens covers, brackets, or panels to the appliance frame at locations that specify this size
• Replaces missing, rusted, or stripped screws that cause loose or rattling parts
• Helps maintain alignment and reduce vibration by keeping components securely attached
• Sized to OEM spec: #10-14 thread, 2 in length

• Disconnect power and, if applicable, shut off water before service
• Start threading by hand to avoid cross-threading; use the correct driver
• Tighten until snug—do not overtighten to prevent stripping
• If the mounting hole or clip is damaged, repair/replace it before installing

This drain hose adapter kit connects the appliance drain hose to the drain outlet, restoring a secure, leak-resistant connection so wastewater flows away reliably. Ideal when the existing connector is cracked, worn, or leaking. What it does:

• Replaces a damaged or missing drain hose connection to stop leaks at the hose outlet
• Provides a sealed transition between the drain hose and the appliance/drain line
• Helps restore normal draining and prevents water pooling under or around the appliance
• Works where worn fittings, broken tabs, or loose hose connections cause water loss

• Disconnect power and water supply before servicing the appliance
• Remove the old adapter and clean mating surfaces before installing the new adapter
• Use appropriate clamps or retainers and tighten securely—replace clamps if corroded or damaged
• After installation, run a short cycle and check the connection for leaks

This cover seals the dishwasher salt filler hole to keep water softener salt contained and reduce leaks or salt contamination in the tub. It restores a proper seal for the salt reservoir opening. What it does

• Covers and seals the dishwasher salt filler hole to help prevent salt granules from spilling into the wash tub.
• Helps limit salt and water leakage from the softener/salt reservoir area.
• Can reduce symptoms related to salt contamination such as visible salt deposits or unexpected residue in the tub.
• Simple replacement that restores the original closure for the salt fill port.

• Turn off power to the appliance before accessing the salt filler area.
• Remove lower racks or panels as needed to reach the salt fill; refer to your owner's manual for guidance.
• Inspect the fill neck and surrounding seals for damage; replace damaged seals as needed.