Jdb8200ap0 Parts

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This electronic control board is the appliance's main control. It directs power and timing to the correct components so cycles run as selected, helping restore consistent operation when the original board has failed.

• Coordinates operation of motors, valves, heaters, and pumps
• Interprets inputs from switches and sensors to manage cycle logic
• Stores and executes programmed options and settings
• Typical symptoms: won't start or advance, unresponsive or flashing controls, error codes, intermittent shutdowns

• Disconnect power before servicing; use ESD protection and handle the board by its edges
• Access is typically through the control console; refer to your model's service sheet for exact location
• Move wire connectors one at a time to the new board and secure it properly
• Perform any required initialization/diagnostic steps for your model after installation

This machine screw secures panels, brackets, and other components inside your appliance. Replacing a missing or damaged fastener restores a solid fit, reduces vibration and rattling, and helps keep assemblies properly aligned for reliable performance.

• 10-32 machine-thread fastener for mounting and securing internal parts and panels
• Helps maintain alignment and structural integrity of assembled components
• Replaces missing, stripped, or damaged hardware
• Reduces rattling, vibration, or loosening from worn fasteners

• Disconnect power; shut off gas or water supplies before servicing
• Match thread and length to the original fastener used in that location
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse original washers or clips if present and in good condition

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This manifold is the OEM gas valve assembly that routes propane or natural gas from the regulator to the oven and burner valves so the appliance can ignite and heat properly. Designed as a direct-replacement service part. What it does

• Channels gas from the regulator to individual burner/oven valves so each burner can ignite.
• Replaces a worn or damaged manifold that can cause weak or no ignition.
• Addresses symptoms such as burners that won't light, oven failing to heat, or inconsistent flame across burners.
• Works with the appliance's existing regulator and control valves when installed correctly.

• Turn off gas supply and electrical power before attempting removal or service.
• Inspect fittings and gaskets; replace any damaged seals to prevent leaks.
• After installation, perform a gas-leak test and verify proper ignition and flame patterns.

This is a 10-32 threaded machine screw used to fasten appliance panels and components securely. It restores proper fit and prevents rattling or loose parts when a missing or stripped fastener causes instability. What it does:

• Fastens panels, trim, brackets, and internal components that use 10-32 threads
• Restores secure fit when a missing or damaged screw lets parts shift or vibrate
• Helps eliminate rattling, loose connections, and alignment issues caused by lost hardware
• Works where a standard 10-32 machine screw is specified by the manufacturer

• Disconnect power and gas before accessing internal components
• Use the correct screwdriver or nut driver to avoid stripping the head
• Do not overtighten; snug until secure to avoid thread damage
• Keep removed hardware for reference and replace only with identical thread size

This touch-up paint restores small chips, scratches and nicks in painted appliance surfaces for a cleaner, like-new appearance. It's ideal for hiding minor cosmetic damage without repainting the whole panel. What it does:

• Covers small chips, scratches and scuffs on painted appliance surfaces
• Helps prevent bare metal exposure that can lead to rusting of small areas
• Restores color and gloss to localized damage for improved appearance
• Applies to control panels, doors and trim where finish is worn

• Shake well before use and apply sparingly with a fine brush, cotton swab or toothpick
• Allow finish to dry fully between light coats for best color match
• Work in a well-ventilated area and avoid inhaling fumes
• Keep out of reach of children and follow local disposal regulations for paint

This small retaining clip secures trim and appliance components to keep panels and assemblies in place, helping prevent rattling and loose parts during use. It's a simple replacement that restores proper fit and alignment. What it does:

• Holds panels, trim, or small assemblies in place to maintain a secure fit
• Prevents rattling, vibration noise, and movement of loose parts
• Replaces broken, bent, or missing clips that allow gaps or misalignment
• Works where a small fastener is needed to secure plastic or metal components

• Disconnect power or unplug the appliance before servicing to avoid shock or injury
• Inspect the mounting area for damage; replace any broken mating tabs or screws for a secure fit
• Installation typically requires basic hand tools such as pliers or a screwdriver; apply steady pressure to snap clip into place

This factory fastener is a #10-16 screw used to secure appliance panels and components. Replacing worn or missing hardware restores a tight fit, helps prevent rattles, and keeps parts properly aligned for dependable operation.

• Secures brackets, panels, and covers to the cabinet or frame
• Replaces missing, stripped, or corroded mounting hardware
• Helps reduce vibration and rattling from loose mounts
• Correct 10-16 thread to match designated OEM mounting points

• Disconnect power and shut off water or gas supply before servicing
• Match the screw to the original location using your model's diagram
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If replacing multiple screws, swap one at a time to maintain alignment

This terminal nut secures a wire terminal to a threaded post or terminal block, ensuring a tight, reliable electrical connection. Replace a missing, stripped, or heat-damaged nut to restore a safe, stable power path to the component. What it does:

• Clamps a ring or spade terminal to a threaded stud/post on a terminal block or component
• Maintains a low-resistance connection to reduce arcing and heat buildup
• Helps address symptoms like loose/burned terminal connections, intermittent power, or discoloration at the connection point
• Direct replacement for the original connection hardware on applicable models

• 1 terminal nut

• Disconnect power at the breaker before servicing; allow any heated components to cool
• Note wire locations; remove damaged hardware and inspect wiring/terminals for heat damage
• Clean threads and install the new nut; tighten snugly without overtightening
• Reassemble and restore power; verify the connection remains cool during initial operation

Cover-Box protects the appliance's control box and internal wiring by enclosing electronic components to keep out dust and accidental contact, helping maintain reliable operation and reduce the chance of component damage. What it does:

• Encloses and protects the control box and wiring from dirt, debris and incidental contact.
• Helps prevent exposed wires and component damage that can lead to intermittent operation or electrical faults.
• Restores structural protection when the original cover is cracked, warped, or missing.
• Matches OEM fit and mounting points to secure the control assembly in place.

• Disconnect power to the appliance before beginning any service.
• Remove screws or fasteners securing the old cover; keep hardware for reuse unless damaged.
• Ensure wiring and connectors are routed correctly and fully seated before reinstalling the cover.

This wire harness routes power and control signals between appliance components to restore reliable electrical connections. Use it when a damaged or shorted harness causes intermittent operation, non-responsive controls, or loss of power to parts. What it does:

• Routes power and signals between the control and components (motors, switches, sensors) to maintain proper electrical paths.
• Replaces frayed, burned, or broken wiring that can cause intermittent operation or blown fuses.
• Addresses common symptoms such as the appliance not starting, controls that don't respond, or specific components failing to run.
• Restores original connector locations and routing for secure, reliable connections.

• Disconnect power (unplug or switch off breaker) before servicing to avoid shock or damage.
• Compare harness routing and connector positions to the removed part before installing to ensure correct fit.
• Reuse original clips and retainers where possible; secure loose wiring away from heat and moving parts.

This push retainer is a small press-on fastener that secures components to shafts or studs inside your appliance. It restores a tight, reliable hold so knobs, trim, or linkages don't loosen or fall off during use. What it does:

• Presses onto a shaft or stud to secure knobs, trim, or linkages—no threads required
• Maintains spring tension to resist vibration during normal operation
• Replaces a missing, bent, or weakened retainer
• Common symptoms: loose or wobbly knobs/trim, parts slipping off, or a retainer that won't stay on

• 1 push retainer

• Disconnect power; for gas appliances, also shut off the gas supply
• Access the shaft/stud and carefully remove the old retainer with pliers; avoid damaging adjacent plastic parts
• Press the new retainer on squarely using a deep socket or nut driver; do not hammer directly
• If the mating shaft or component is damaged or deformed, address that before installing the new retainer

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This 10-24 threaded screw secures appliance components that use a #10 machine screw. It provides reliable fastening for panels, brackets, and assemblies so parts stay aligned and stable during normal use and service. What it does:

• Fastens panels, brackets, or assemblies that accept a 10-24 machine screw
• Maintains alignment and structural connection under normal operating loads
• Replaces worn, stripped, or missing screws to restore secure mounting
• Works with sheet-metal and component mating nuts or threaded inserts commonly used in appliances

• One 10-24 threaded screw

• Power tools can be used; avoid overtightening to prevent stripped threads or damaged components
• Disconnect power and follow all safety steps for your appliance before servicing
• Ensure proper engagement and torque to avoid damage