Jds 88850Aab Parts

The Noise Filter is an OEM part for Whirlpool built-in wall ovens. It is installed inside the oven cavity near components that produce vibrations, such as the convection fan motor. 

Causes of a faulty noise filter include the degradation of noise-dampening materials over many heating and cooling cycles. Physical damage from accidental impact during cleaning could also compromise its sound-blocking ability.

Symptoms of a bad noise filter include: 

• Excessive buzzing or humming noises emitted from the oven cavity
• Louder than normal fan or component sounds carrying into the kitchen
• Vibrations felt externally on the oven chassis during operation

This OEM replacement fits several Whirlpool, KitchenAid, and Jenn-Air wall oven models.

The Surface Burner Valve is an OEM part for Whirlpool cooktop ranges. As an internal fixture, each valve regulates gas flow to a specific burner allowing customized heating levels. 

Symptoms of a bad surface burner valve include:

• Burners that will not ignite or only ignite at max capacity
• Inability to lower a burner's flame below the maximum setting  
• Gas leaks characterized by unusual smells 

Causes relate to regular use corrosion restricting valve movement or impact damaging stems preventing full aperture control. Neglect threatens safety.

This OEM Whirlpool part is also compatible with some Maytag, Jenn-Air, and KitchenAid ranges.

Razor blade scraper.

This door-activated switch detects when the oven door opens or closes and signals the appliance to control the interior light. Replacing a worn or failed switch restores dependable light operation and accurate door-status feedback.

• Senses oven door position and opens/closes the light circuit
• Controls the oven's interior light based on door position
• Provides door-status input to the control for normal operation
• Typical symptoms: light stays on, won't turn on, or flickers with door movement; door-ajar messages may appear

• Disconnect power at the breaker or unplug the unit before servicing
• Access the switch from behind the front frame or control area, depending on model
• Move wires to the new switch one at a time to maintain correct positions; secure with existing hardware
• Restore power and verify light operation with door open/closed before reassembly

This 8-inch coil surface element restores reliable heat on electric ranges. Replace a worn or failed burner to bring back consistent heating and everyday cooking performance on your cooktop. What it does:

• Heats cookware at the 8-inch cooking zone by converting electrical power into heat
• Common fix for a burner that won't heat, heats intermittently, or shows visible damage/blistering
• Plugs into the existing surface element receptacle and rests on the cooktop supports
• Helps restore even, consistent heating when the original coil has burned out

• 1 8-inch coil surface element

• Disconnect power at the breaker or unplug the range before servicing
• Allow the element to cool completely before handling
• Lift the old element slightly and pull straight out from the receptacle; avoid twisting or prying
• Align terminals and push the new element firmly into the receptacle until fully seated, then test

This mounting bracket secures the surface element terminal block to the cooktop. Replacing a bent or missing bracket helps keep the coil element connection aligned and stable so the burner plugs in firmly during use.

• Provides a fixed mount for the surface element receptacle beneath the burner opening
• Helps prevent the terminal block from shifting, sagging, or rotating when inserting/removing the element
• Common symptoms include a loose or wobbly receptacle, element not seating fully, or visible bracket damage/missing bracket
• Replace if the bracket is bent, broken, or cannot hold the receptacle in position

• Disconnect power at the breaker and allow the cooktop to cool completely
• Remove the surface element and lift/open the cooktop to access the terminal block area
• Transfer the receptacle/terminal block onto the new bracket and secure with existing hardware, ensuring correct alignment
• The element prongs insert smoothly before restoring power

This replacement grill grate restores a sturdy, level grilling surface on your cooktop or range. Replace a cracked, warped, or missing grate to maintain safe support and consistent heat over the grill area.

• Provides the elevated grilling surface above the heat source for stable, even cooking
• Keeps food positioned at the proper height for consistent searing and results
• Replace if cracked, broken, warped, or heavily corroded
• Helps resolve rocking/unstable surface or uneven cooking caused by a damaged grate

• Turn appliance off and allow all surfaces to cool completely before handling
• Lift off the old grate and clean debris from the support ledges or frame
• Set the new grate in the correct orientation; ensure it sits flat and stable
• Verify proper clearance around adjacent components before use

This surface burner valve regulates gas flow to a single cooktop burner through the control knob. Replacing a worn valve restores smooth flame control, reliable ignition, and a positive shutoff for safer, consistent cooking.

• Regulates and meters gas to one surface burner for off, simmer, and full-flame settings
• Works with the control knob and spark-ignition switch to light the burner
• Common symptoms: burner won't light or adjust properly, flame doesn't shut off completely, or the knob is hard to turn or wobbly
• If a gas odor is detected near the control area, stop use and service the appliance

• Disconnect electrical power and shut off gas before servicing; allow the appliance to cool
• Access the valve/manifold; note valve orientation and stem position before removal
• Transfer the spark switch, mounting clip, and fittings from the old valve as needed
• Apply an approved gas-rated thread sealant, tighten connections, and leak-test all joints with a soap solution before use

Replacement fastener used to secure appliance components. If a screw is missing or damaged, panels and brackets can loosen or rattle. Installing a new screw restores a tight fit and helps keep parts properly aligned.

• Fastens panels, brackets, or internal components as designed for the model
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration/rattling and restores proper fit
• Maintains alignment and a secure assembly after service

• Disconnect power; shut off gas if applicable before servicing
• Support components while removing/installing fasteners
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace all required screws in a location for even clamping and proper fit

This replacement screw fastens panels, brackets, or trim inside your appliance. Swapping in a new screw restores a tight, secure fit and helps stop rattles, looseness, or misalignment caused by missing or damaged hardware.

• Secures panels, brackets, or trim to the appliance chassis
• Helps maintain proper alignment and spacing of components
• Replaces missing, rusted, or stripped hardware
• Helps resolve loose panels/handles, vibration, or rattling noises

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Match the screw to the original location; start threads by hand to avoid cross-threading
• Use the appropriate driver and tighten snugly without overtightening
• Inspect the mounting hole or clip for damage and address as needed before reassembly

This indicator light installs in the control panel of compatible ranges/cooktops and illuminates to show when a heating element or function is active. Replacing a failed lamp restores clear, at-a-glance status feedback during use.

• Provides visual confirmation when a surface element or function is turned on
• Common failure symptoms include no light, intermittent flicker, or very dim illumination
• May also be referred to as a pilot light or panel indicator
• Visual indicator only; does not control heating performance

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the appliance to cool completely
• Access the console/backguard area; note wire positions and move them to the new light one at a time
• Seat and secure the light, restore power, and test operation before reassembly

A light indicator is installed on ranges and wall ovens as a safety feature. The purpose of the light indicator is to tell the user when the appliance is in operation. When the unit is heating up or running, the light indicator will illuminate. A replacement part is necessary if the component is no longer functioning.A visual inspection will determine if the light indicator is working. Turn the oven on, and if the light doesn't glow, it's broken. Replacing the light indicator is a quick and easy process. Unplug the range from its power source before starting. An adjustable wrench or nut driver is required to make the replacement. The light indicator is located inside the cover plate of the appliance.This light indicator is an authentic OEM replacement part. It is sold as an individual unit. It comes sourced directly from the manufacturer. The light indicator is made of durable, high-quality materials. The component is compatible with several models of ranges. It fits into products produced by General Electric, RCA, and Hotpoint.

Color: White. Size: 2 oz. can. Porcelain touch-up paint.

The Display Wire Harness is an OEM part for Whirlpool ranges. It connects the control panel display to the range’s main control board, allowing for communication between the user interface and the appliance’s electronic system. This harness ensures that the display panel accurately shows information such as temperature settings, timer functions, and error codes.

Causes of a bad display wire harness can include regular wear and tear, electrical issues, or damage from heat exposure or physical impact. When the wire harness fails, it can disrupt the flow of information between the control panel and the main control board, affecting the operation and display functions of the range.

Symptoms of a bad Display Wire Harness include:

• The display panel not lighting up
• Inaccurate or flickering display readings
• Buttons on the control panel not responding
• Error codes appearing on the display

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This electronic control board restores responsive touchpads, displays, and timed cooking functions on compatible ranges and ovens. Replace a faulty board to regain reliable cycle selection, temperature control, and accurate clock/timer operation. What it does:

• Manages console inputs, display readouts, timers and cooking cycle controls
• Sends signals to the oven's heating and safety systems for bake, broil and timed events
• Common symptoms of failure: blank or flickering display, unresponsive touchpad/buttons, erratic timers, or oven not starting
• May show error codes or intermittent function losses when failing

• Disconnect power at the breaker before attempting repair to avoid shock or damage
• Take photos of wiring before removal and transfer connectors to the new board exactly as found
• Use appropriate tools and handle the board by its edges to avoid electrostatic damage

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.