Jgs07peh1ww Parts

This painted screw head is a cosmetic and protective cap that restores the finished look where a visible screw is used. It covers the screw head and helps match surrounding black trim for a clean appearance. What it does:

• Covers and conceals a screw head to improve appearance of panels, trim, or bezels
• Helps protect the screw head from direct exposure and reduces visible wear
• Used when trim or panels show exposed or mismatched screw heads
• Common fix when screw heads are scratched, discolored, or visually distracting

• Use the matching screw and press or snap the cap into place over the screw head
• Disconnect power and remove any panels only as recommended by your appliance manual before working near electrical components
• Avoid forcing or prying the cap; if tight, gently ease it on to prevent breakage
• Replace any damaged caps with the exact part to maintain fit and finish

This cable clamp secures the appliance power cord where it enters the cabinet, protecting wiring from pull and chafe for safer, more reliable operation. Designed to hold the cord firmly in place and prevent accidental disconnection. What it does:

• Acts as a strain relief to prevent the power cord from pulling into or away from the appliance
• Protects wiring from abrasion and sharp edges at the entry point
• Helps maintain a secure electrical connection to reduce intermittent power issues
• Commonly used where the cord passes through a rear or bottom access panel

• Disconnect power before inspecting or replacing the clamp to avoid shock or injury
• Install at the cord entry so the clamp captures the cord jacket; tighten fastener securely but do not over-torque
• Verify the cord is correctly routed and not pinched when reassembling panels
• If any wiring or the cord jacket is damaged, replace the cord before restoring power

This is a right-side guide support that secures and aligns a sliding component so drawers or shelves operate smoothly and stay on track. Replaces a worn or broken guide support to restore proper movement and seating. What it does:

• Holds the right-side guide rail or track in place so the drawer or shelf slides evenly
• Prevents the drawer or shelf from sagging, binding, or falling off the track
• Restores proper alignment when the original guide is cracked, broken, or worn
• Works with the existing rail, clips, and mounting hardware to maintain smooth travel

• Disconnect power or unplug the appliance before accessing internal components
• Access may require removing the drawer, shelf, or front panel—use basic hand tools
• Inspect related clips, rails, and fasteners and replace any damaged pieces for best results

This oven felt seal fits around the door perimeter to cushion the door and help reduce heat loss. It restores the intended door clearance and soft contact between the oven door and frame for safer, quieter operation. What it does:

• Cushions the oven door edge to prevent metal-on-metal contact and reduce rattling
• Helps limit heat and smoke from escaping the oven cavity when the door closes
• Restores proper door clearance to prevent scraping or uneven sealing
• Commonly replaced when felt is worn, compressed, torn, or missing

• One oven felt seal as shown

• High-level replacement; remove the oven door or open hinge per your service manual before replacing the seal
• Work with the oven powered off and fully cooled; disconnect power for safety
• Press the felt into the channel or adhesive area; ensure even fit around the full perimeter

Right hand side

A receiver hinge that secures and supports an oven door hinge pin to keep the door aligned and operating smoothly. Replaces a worn or broken receiver to restore proper door fit and movement. What it does

• Accepts and retains the oven door hinge pin so the door opens and closes correctly.
• Supports door weight to prevent sagging or uneven alignment.
• Helps the door latch and seal properly for safe, consistent operation.
• Commonly replaced when the door drops, rubs, or will not stay closed.

• One receiver hinge

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the oven door or access panel per the service manual for safer installation.
• Use basic hand tools; check hinge pins and mating hardware for wear and replace if needed.

This glow-bar oven igniter lights the gas burner. When energized, it heats and draws current through the safety valve so the bake or broil flame ignites reliably and the oven reaches the set temperature. What it does:

• Heats and ignites the oven's bake or broil burner
• Draws the correct current to open the gas safety valve
• Can address no-heat or no-ignition conditions
• Helps resolve very slow preheat or inconsistent oven temperatures
• Useful when the igniter glows but the burner never lights

• 1 glow-bar igniter

• Disconnect power and shut off gas supply before servicing
• Access from the oven cavity; remove racks, oven bottom, and flame spreader as needed
• Handle the igniter carefully—element is fragile; avoid touching the carbide/ceramic tip
• Secure connections and route wires away from flames and high-heat areas; test operation after reassembly

The BURNER VALVE is an OEM part for GE gas ranges. It regulates gas flow to individual cooktop burners, controlling flame size and heat output based on valve position.

Symptoms of a bad burner valve include: 

• Inability to adjust or maintain desired flame levels
• Gas odor or clicking/hissing noises from the burner area  
• Burners that remain constantly on without response to controls

Gas valves can weaken or crack over many heating/cooling cycles. Mineral buildup may also restrict precise flow regulation. Replacing the faulty valve with this genuine GE part restores the burners' heat-adjustable functionality for custom cooking power. 

This OEM GE replacement burner valve is also compatible with some Kenmore and RCA gas range models. Reliable control over burners maximizes versatility and safety.
 

The Grate Assembly is an OEM part for GE ranges. This part consists of the grates that sit above the burner components on gas stove tops.

The grate assembly is responsible for providing a stable platform for cookware and making sure there is even heat distribution for cooking. 

Causes of a bad grate assembly can include warping or damage from continued exposure to heat. Burned on or stuck-on debris that compromises heat transfer is also a common issue.

Symptoms of a failed grate assembly include:

• Grates that are loose, wiggly, or detached from their mounting points
• Grates with cracks, holes, or broken tines that no longer fully cover the burners
• Grates that are heavily discolored or corroded from burned-on foods or liquids

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

The convection fan is an OEM component for Whirlpool ranges. It functions as the convection fan system, circulating hot air within the oven cavity to provide efficient all-around heating. 

The convection fan is responsible for proper air circulation and temperature distribution during convection bake and roast cycles. It allows for fast, even cooking on multiple racks simultaneously.

Symptoms of a bad convection fan include:

• Inefficient or uneven baking/cooking results  
• Longer than normal cook times
• Overheating or hot spots within the oven
• Strange noises coming from the convection fan area

Causes can include a failed motor, worn fan blades, or blockages that disrupt airflow.

This Whirlpool OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ranges.

This insert is a small OEM component designed to fit into a specific location on your appliance to secure, align, or finish an assembly. Replacing a worn, damaged, or missing insert restores proper fit and clean appearance.

• Provides a snug interface or cover within the designated assembly
• Helps prevent looseness, vibration, or gaps in the connected part
• Replaces cracked, worn, or missing insert pieces
• Common symptoms include loose or wobbly parts, misalignment, or a missing cap/cover

• Disconnect power and shut off gas/water before servicing
• Refer to your model's parts diagram to confirm location and orientation
• Use non-marring tools to avoid cosmetic damage
• Seat the insert fully; do not overtighten adjacent fasteners