Jvm316od4cc Parts

This control panel assembly replaces a damaged or unresponsive user interface so you can reliably select settings and operate the appliance. It restores a clean, factory fit when the original panel becomes cracked, sticky, or worn.

• Provides the front user interface housing and keypad/touchpad area
• Sends key-press signals to the control system via the ribbon connector
• Replaces broken, faded, or physically damaged panels
• Helps resolve unresponsive or intermittent keys, stuck buttons, or keypad-related error beeps/codes

• Disconnect power at the breaker before servicing
• On microwave models, internal high-voltage components can retain a charge even when unplugged—use extreme caution
• Support the panel while removing screws; don't stress the wiring or ribbon cable
• If applicable, transfer any reusable boards, clips, or light pipes from the old panel; seat the ribbon connector straight and fully

Restore heat in your microwave with this high voltage transformer. It steps household power up to energize the magnetron, addressing no-heat and loud-hum complaints when the original transformer shorts or weakens.

• Steps household AC up to the high voltage required by the magnetron
• Works with the high-voltage capacitor and diode in the heating circuit
• Failure can cause the microwave to run but not heat
• A shorted transformer may cause loud buzzing, burning odor, or blow a fuse/trip a breaker

• Unplug the appliance. The high-voltage capacitor can hold a dangerous charge—proper discharge and safety procedures are essential.
• Remove the outer cabinet to access the HV section; safely remove and support over-the-range units if applicable.
• Label and transfer all wires; connect to the correct primary and secondary/HV terminals and secure the chassis ground.
• Mount the transformer firmly and route wiring away from sharp edges and hot components.

This damper is the oven vent assembly that controls airflow and venting during cooking, helping the oven purge steam and maintain consistent temperatures. Replacing a faulty damper restores proper vent operation and helps improve cooking performance. What it does:

• Opens and closes the oven vent to regulate airflow and release steam during bake/broil cycles
• Helps maintain proper cooking temperatures by directing exhaust flow
• A failed damper can cause poor temperature recovery, uneven baking or unexpected venting behavior
• Works as the airflow control component in the oven vent system

• Disconnect power to the appliance before starting any repair
• Installation typically requires basic hand tools (screwdriver, nut driver); follow the service manual for disassembly steps
• Handle sheet metal and vents carefully — wear gloves to avoid cuts

This handle assembly replaces a worn, cracked or broken refrigerator door handle so the door opens and closes easily and looks finished. It restores a secure grip and clean appearance without replacing the whole door. What it does

• Serves as the exterior door handle for opening and closing the appliance
• Replaces handles that are cracked, loose, or have damaged mounting points
• Restores proper handhold and improves door usability and appearance
• Helps prevent further damage from using a compromised handle

• One handle assembly

• Basic hand tools required; keep fasteners and trim pieces organized during removal
• Follow manufacturer instructions for door trim/handle access; avoid overtightening screws
• Wear gloves to protect fingers from sharp edges and to avoid fingerprints on finished surfaces
• If the door has wiring or trim panels nearby, disconnect power to the appliance before servicing

This ventilation motor drives the exhaust/vent fan that helps move air through the appliance, restoring proper airflow and helping reduce heat and odors. Designed as a direct replacement to restore ventilation performance. What it does:

• Spins the vent fan to circulate air through the appliance cabinet and exhaust paths
• Helps reduce overheating by keeping airflow through vents and ducts
• Resolves weak or no exhaust airflow, unusual fan noise, or intermittent fan operation
• Matches OEM fit and mounting points for straightforward replacement when specified

• Disconnect power to the appliance before beginning any service
• Handle the motor and wiring carefully; match connector and mounting orientation during install
• Inspect vent housing, fan blades, and wiring harness for damage when replacing the motor

This is a white control panel assembly with integrated white LED display that replaces a worn or damaged range/stove control interface. Restores visible controls and display feedback so oven functions respond and show settings clearly. What it does:

• Replaces a cracked, faded, or non-responsive control panel and associated front display
• Restores readable LED indicators and touch/button surfaces for selecting bake, broil, timers and other functions
• Helps resolve issues where display segments are dim, buttons stick, or the panel housing is cosmetically damaged
• Works with the original electronics and wiring harness when properly mounted

• High-level replacement only; disconnect power before attempting service to avoid shock
• Panel may attach with screws and clips; handle carefully to avoid damaging attached LEDs or trim
• Reuse existing mounting hardware and wiring harness

This stainless steel outer oven door assembly replaces a damaged or worn exterior door to restore appearance and sealing. It provides a finished stainless look and a proper closure for safe, efficient oven operation. What it does:

• Replaces a dented, scratched, or bent outer oven door to restore cosmetic appearance
• Helps the oven door close properly to maintain internal temperature and cooking performance
• Replaces a door with damaged trim or exterior paneling
• Returns a clean stainless finish for a like-new exterior

• Disconnect power to the appliance before starting any repair.
• Door assemblies can be heavy and awkward—use two people to avoid injury or damage.
• Handle edges and any broken glass carefully and wear protective gloves if needed.
• Follow the manufacturer instructions for correct alignment and screw torque.

This control mounting panel secures the appliance control/console assembly, providing a stable mounting surface that helps keep buttons, switches, and electronics aligned for reliable operation and easier repairs. What it does:

• Provides a rigid mounting surface for the control/console assembly
• Keeps control board and user interface components properly aligned
• Helps prevent movement or vibration-related contact issues
• Common replacement for cracked, bent, or damaged control panels that misalign controls

• Disconnect power to the appliance before starting any repair
• Typically accessed by removing the console or outer panel; keep fasteners organized
• Handle the control board and connectors carefully to avoid damage

The Capacitor is an OEM part for GE microwaves. It is an electronic component within the microwave's high voltage circuitry. The capacitor works to store and deliver high-voltage electrical energy from the main control board to the magnetron tube in short, powerful bursts required for microwave cooking.

Causes of failure can be due to natural breakdown of the capacitive material over time and use. Capacitors have a limited lifespan that is greatly reduced if subjected to heat, moisture or electrical surges.

Symptoms of a bad capacitor include:

• Inconsistent or incomplete cooking even at high power levels
• Slow or inefficient heating during use
• Sparking or burning smells emanating from inside the microwave

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This control panel replaces a damaged or worn front panel and restores the oven's user controls and display visibility. It provides the finished slate appearance and white LED illumination for clear button and readout visibility. What it does:

• Houses the oven control buttons and LED display so you can select functions and monitor settings.
• Restores visible white LED indicators and backlighting for easier reading in low light.
• Replaces cracked, scratched, or discolored front panel surfaces that interfere with operation.
• Helps resolve unresponsive or hard-to-read control areas when the original panel is physically damaged.

• One slate control panel with white LED as shown.

• High-level replacement; basic hand tools required and panel mounts with screws and clips.
• Disconnect power at the breaker or unplug the range before starting to avoid shock.
• Handle LEDs and circuit areas carefully; avoid contact with wiring and circuit board surfaces.

This control panel overlay replaces the labeled face on a range/oven control panel to restore legible buttons and a clean appearance. It protects the underlying control surface and helps prevent wear-related mis-reads. What it does:

• Replaces faded, worn, or damaged control panel labeling so settings and buttons are clear
• Protects the control surface from spills, grease, and everyday wear
• Helps restore the oven/range's appearance without replacing the entire console
• Can resolve user errors caused by unreadable or missing button markings

• One control panel overlay

• Disconnect power to the appliance before beginning any work
• Some installations require removing the control panel or trim; keep fasteners and note their locations
• Peel-and-stick or screw-in methods vary by model—align carefully before securing

This is a binding-head screw used to fasten panels and components on compatible GE appliances. It provides secure, low-profile fastening where a binding head design is required for proper fit and alignment. What it does

• Secures panels, brackets, or small assemblies to prevent movement or rattling.
• Replaces a missing or stripped screw that causes loose parts or squeaks.
• Restores proper alignment for components that rely on the binding-head profile.
• Works where a shallow, rounded head and threaded shaft are specified.

• Use the correct driver size to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or damaging parts.
• Disconnect power and follow all appliance-specific safety procedures before accessing panels.