Kdfe104 Hbl0 Parts

This touch-up paint restores small chips, scratches and nicks in painted appliance surfaces for a cleaner, like-new appearance. It's ideal for hiding minor cosmetic damage without repainting the whole panel. What it does:

• Covers small chips, scratches and scuffs on painted appliance surfaces
• Helps prevent bare metal exposure that can lead to rusting of small areas
• Restores color and gloss to localized damage for improved appearance
• Applies to control panels, doors and trim where finish is worn

• Shake well before use and apply sparingly with a fine brush, cotton swab or toothpick
• Allow finish to dry fully between light coats for best color match
• Work in a well-ventilated area and avoid inhaling fumes
• Keep out of reach of children and follow local disposal regulations for paint

This small retaining clip secures trim and appliance components to keep panels and assemblies in place, helping prevent rattling and loose parts during use. It's a simple replacement that restores proper fit and alignment. What it does:

• Holds panels, trim, or small assemblies in place to maintain a secure fit
• Prevents rattling, vibration noise, and movement of loose parts
• Replaces broken, bent, or missing clips that allow gaps or misalignment
• Works where a small fastener is needed to secure plastic or metal components

• Disconnect power or unplug the appliance before servicing to avoid shock or injury
• Inspect the mounting area for damage; replace any broken mating tabs or screws for a secure fit
• Installation typically requires basic hand tools such as pliers or a screwdriver; apply steady pressure to snap clip into place

This inline fuse is a replaceable safety device that protects your appliance's wiring and components from overcurrent. It restores circuit protection so the appliance can operate safely after a blown fuse is replaced. What it does:

• Protects the wiring harness and electrical components by interrupting power if a short or overload occurs
• Commonly used where a single-point fuse is needed inline with a circuit
• Resolves symptoms like a non-starting unit, intermittent power loss, or a tripped circuit when caused by a blown fuse
• Works as part of the appliance's electrical protection system when installed in the proper harness location

• Disconnect power to the appliance before inspecting or replacing the fuse
• Visually check the blown fuse or use a multimeter before replacing
• Install only in the correct harness location and ensure secure wire connections
• If the replacement fuse blows immediately, stop and diagnose the underlying short or fault

This factory fastener is a #10-16 screw used to secure appliance panels and components. Replacing worn or missing hardware restores a tight fit, helps prevent rattles, and keeps parts properly aligned for dependable operation.

• Secures brackets, panels, and covers to the cabinet or frame
• Replaces missing, stripped, or corroded mounting hardware
• Helps reduce vibration and rattling from loose mounts
• Correct 10-16 thread to match designated OEM mounting points

• Disconnect power and shut off water or gas supply before servicing
• Match the screw to the original location using your model's diagram
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If replacing multiple screws, swap one at a time to maintain alignment

This terminal nut secures a wire terminal to a threaded post or terminal block, ensuring a tight, reliable electrical connection. Replace a missing, stripped, or heat-damaged nut to restore a safe, stable power path to the component. What it does:

• Clamps a ring or spade terminal to a threaded stud/post on a terminal block or component
• Maintains a low-resistance connection to reduce arcing and heat buildup
• Helps address symptoms like loose/burned terminal connections, intermittent power, or discoloration at the connection point
• Direct replacement for the original connection hardware on applicable models

• 1 terminal nut

• Disconnect power at the breaker before servicing; allow any heated components to cool
• Note wire locations; remove damaged hardware and inspect wiring/terminals for heat damage
• Clean threads and install the new nut; tighten snugly without overtightening
• Reassemble and restore power; verify the connection remains cool during initial operation

Cover-Box protects the appliance's control box and internal wiring by enclosing electronic components to keep out dust and accidental contact, helping maintain reliable operation and reduce the chance of component damage. What it does:

• Encloses and protects the control box and wiring from dirt, debris and incidental contact.
• Helps prevent exposed wires and component damage that can lead to intermittent operation or electrical faults.
• Restores structural protection when the original cover is cracked, warped, or missing.
• Matches OEM fit and mounting points to secure the control assembly in place.

• Disconnect power to the appliance before beginning any service.
• Remove screws or fasteners securing the old cover; keep hardware for reuse unless damaged.
• Ensure wiring and connectors are routed correctly and fully seated before reinstalling the cover.

This cup shelf assembly replaces a damaged or missing refrigerator door shelf to restore secure storage for cups, bottles and small items. It snaps into the door for everyday organization and keeps items from shifting during use. What it does:

• Provides a stable shelf on the refrigerator door to hold cups, bottles and jars
• Replaces cracked, broken or missing door shelf that lets items fall or shift
• Restores original door storage layout and helps prevent spills
• Fits the door's existing mounting points for a secure hold

• One cup shelf assembly (11")

• Remove contents from the door area before installing
• Often snaps into place; may require basic hand tools to remove the old shelf
• Do not force parts; align mounting tabs and press evenly until seated

The Harns-Wire is an OEM component specifically designed for Whirlpool brand dishwashers. This harness connects and routes wires between electrical components within the dishwasher like the control console, heating element, circulation pump and other critical systems. 

Symptoms of a bad harness include:

• Lights or sensors unexpectedly turning off  
• Intermittent or abnormal dishwasher operation
• Appliance not starting or unexpected shutdowns
• Water or heating issues during cycles
• Visible damage or exposed wires

Causes of a bad harness can include wear and tear from regular usage, cracks or cuts in the wire insulation over time, loose/corroded connections or damage from physical strain. 

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air and some Kenmore models.

The Leveling Leg is an OEM part for Whirlpool dishwashers. It is an adjustable leg that is used to level the dishwasher and stabilize it when installed under the kitchen counter or inside cabinetry.  

Causes of a bad leveling leg often relate to normal wear and tear over time, repeated adjustments, or potential overtightening that leads to thread damage.

Symptoms of a bad leveling leg include:

• The dishwasher is not sitting level and appears unstable  
• Leaks occurring around the dishwasher perimeter or door seal
• Drainage or pooling of water inside the dishwasher
• Cabinetry or countertops showing scratches or wear

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

The Terminal Block is an OEM part for Whirlpool dishwashers.The terminal block facilitates the flow of electricity throughout the appliance, enabling functions like water heating, pump operation, and cycle control.

Causes can be normal wear over time, or damage from moisture exposure. If you notice any of the above symptoms, replace the terminal block with this genuine OEM part to restore reliable electrical connections and proper operation.

Symptoms of a bad terminal block include:

• The dishwasher not starting or unexpected beeping/error codes
• Sudden lack of hot water or drying issues
• Electrical shock hazard from exposed terminals

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This lower wiring harness assembly routes power and signals to the appliance's lower components, restoring proper electrical connections so the unit can operate reliably. It's a direct-replacement harness used where factory wiring was damaged or disconnected. What it does:

• Replaces the lower cabinet wiring that connects switches, sensors and motor/valve circuits
• Restores power and signal paths that can cause intermittent operation or failure to run
• Helps eliminate loose, frayed or broken wire connections that create electrical faults
• Supports safe, correct routing and connector fit for reliable component function

• One lower wiring harness assembly as shown

• Disconnect power (unplug or shut off breaker) before starting any work
• Take a photo of the original wiring and connector positions to ensure correct reassembly
• Route the harness exactly as OEM; avoid pinching or sharp edges and secure with existing clips/fasteners

The Clip is an OEM part for Whirlpool dishwashers. It securely attaches the drain hose in place, directing wastewater out of the dishwasher during drain cycles.

Causes of a bad clip can be cracks, breaks, or deformations causing weakened grip. Normal wear and repeated drain cycles can also damage the clip over time.

Symptoms of a bad drain hose clip include:

• Water or leaks around the base of the dishwasher
• Puddles forming due to the hose slipping out of place
• Improper drainage if the hose is not positioned correctly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Wire Harness Assembly is an OEM component for Whirlpool dishwashers. It is the main electrical wiring component that connects and transmits power between various areas and modules inside the dishwasher. 

Causes of a bad wire harness can include cracked, frayed, or damaged insulation over wiring due to normal movement and vibration during the wash cycle. 

Symptoms of a bad wire harness assembly include:

• Lights or elements failing to power on as expected  
• Control panel malfunctions or unintended switches in operation modes
• The entire dishwasher ceasing to function

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models.

This push retainer is a small press-on fastener that secures components to shafts or studs inside your appliance. It restores a tight, reliable hold so knobs, trim, or linkages don't loosen or fall off during use. What it does:

• Presses onto a shaft or stud to secure knobs, trim, or linkages—no threads required
• Maintains spring tension to resist vibration during normal operation
• Replaces a missing, bent, or weakened retainer
• Common symptoms: loose or wobbly knobs/trim, parts slipping off, or a retainer that won't stay on

• 1 push retainer

• Disconnect power; for gas appliances, also shut off the gas supply
• Access the shaft/stud and carefully remove the old retainer with pliers; avoid damaging adjacent plastic parts
• Press the new retainer on squarely using a deep socket or nut driver; do not hammer directly
• If the mating shaft or component is damaged or deformed, address that before installing the new retainer

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This 10-24 threaded screw secures appliance components that use a #10 machine screw. It provides reliable fastening for panels, brackets, and assemblies so parts stay aligned and stable during normal use and service. What it does:

• Fastens panels, brackets, or assemblies that accept a 10-24 machine screw
• Maintains alignment and structural connection under normal operating loads
• Replaces worn, stripped, or missing screws to restore secure mounting
• Works with sheet-metal and component mating nuts or threaded inserts commonly used in appliances

• One 10-24 threaded screw

• Power tools can be used; avoid overtightening to prevent stripped threads or damaged components
• Disconnect power and follow all safety steps for your appliance before servicing
• Ensure proper engagement and torque to avoid damage