Kdfe104 Hbl0 Parts

This wire harness routes power and signals between the appliance's control components and motors, switches, and sensors to restore reliable electrical connections. Replacing a damaged harness returns proper circuit routing and connection integrity. What it does

• Connects control board outputs to motors, switches, sensors, and other electrical components
• Restores broken, frayed, or corroded wiring that can cause intermittent or no operation
• Helps eliminate faults caused by loose or damaged connectors and open circuits
• Supports normal communication between components so controls can operate correctly

• One replacement wire harness as shown

• Disconnect power at the breaker or unplug the appliance before starting any work
• Compare the new harness to the original for connector type, length, and terminal locations before installation
• Route wiring away from sharp edges and moving parts; secure with existing clips or ties

The Lower Door Seal Assembly is an OEM part for Whirlpool dishwashers. As a key component, this seal is designed to create a tight barrier between the door interior and tub during wash cycles. The pliable rubber seal provides a sturdy gasket to block water, detergent, and sound.

Causes of failure involve mineral buildup, cracks from repeated use, or degradation of adhesive over time compromising the seal. 

Symptoms of a faulty seal assembly include: 

• Puddles or leaks from beneath the door frame
• Higher water consumption or longer cycles   
• Increased noise levels during operation

This OEM Whirlpool replacement is also compatible with select KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and other brands.

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dishrack Stop Clip is an OEM component specifically designed for Whirlpool brand dishwashers. This clip functions to hold the upper dish rack in place during washing cycles.

Symptoms of a bad dishrack stop clip can include:

• Movement or vibration of the upper dish rack during washing
• Visible damage, bending or broken tabs on the mounting clip itself  
• Inability to smoothly slide or remove the upper dish rack

Causes of a bad dishrack stop clip usually stem from normal wear and tear over extended use. Overtight loading of dishes could also put excessive stress on the clip.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Replacement door hinge designed to restore proper alignment and smooth opening for compatible refrigerator doors. Replaces worn or damaged hinges to reduce sagging, rubbing, and uneven closing for better seal and operation. What it does:

• Supports and pivots the refrigerator door for smooth opening and closing.
• Restores correct door alignment to improve gasket contact and cold-air seal.
• Stops door sag, uneven gaps, or rubbing against the cabinet.
• Helps eliminate noisy or stiff door movement caused by a worn hinge.

• Disconnect power to the appliance and remove food from the door area before starting.
• Support the door securely while removing and installing the hinge to prevent dropping or damage.
• Reuse original fasteners only if undamaged; replace any stripped or corroded hardware.

The Cntrl-Elec is an OEM part for Whirlpool dishwashers. As the control and electronic component, it governs all of the major functions and operations of the dishwasher. The control board contains integrated circuits, microprocessors, and electronic components that facilitate cycles, temperature regulation, safety features, and user input.

Over time, the electronic components inside the controller can degrade or become damaged. Environmental factors like surges, fluctuations in power, and other electrical issues may also potentially cause failure. 

Symptoms of a bad controller can include:

• Not operating or cycling at all
• Inability to start or stop cycles
• Fault codes displayed
• Issues with heating or drying
• Buttons or control panel not responding

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Seal is an OEM part for Whirlpool dishwashers. It prevents water leaks from the dishwasher door during wash cycles and water heating drainage. Properly installed seals around the door perimeter maintain water pressure inside the dishwasher tub and ensure leak-free operation. 

Causes of a bad seal can include cracks or breaks after extended use of the door opening and closing, exposure to heat and chemicals from regular dishwasher operation, or loose or improper installation.

Symptoms of a bad seal include:

• Water leaks visible around the edge of the door during wash cycles
• Puddles or drips left on the kitchen counter or floor after use   
• Difficulty closing or latching the dishwasher door securely

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Float Switch is an OEM part for Whirlpool dishwashers. It is a safety component that detects water levels and monitors flood conditions. The float switch ensures the dishwasher only runs water when needed and shuts off water flow if it detects a potential leak or overflow situation. 

Symptoms of a bad float switch include: 

• The dishwasher fails to fill with water or stop the water when the cycle is complete
• Loud buzzing or humming noises coming from the float switch area  
• Water leaks inside or outside of the dishwasher due to overfilling
• Repeated error codes related to flooding or water level detection

Causes of a bad float switch could be wear and tear over time, defective wiring or electronic components inside the switch, or damage from moisture or leaks. 

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This dishwasher detergent and rinse aid dispenser stores detergent and releases it at the correct point in the cycle while metering rinse aid. Replacing a worn dispenser restores consistent soap release, cleaning performance, and spot-reducing rinse aid delivery.

• Holds detergent and rinse aid and seals to the inner door
• Opens the detergent cup at the programmed time during the wash
• Meters rinse aid into the final rinse to help reduce spotting
• Typical symptoms: detergent left in cup, dispenser door won't open, rinse aid not dispensing, or leaks around the dispenser area

• Disconnect power to the dishwasher before servicing
• Access from the inner door by removing the perimeter screws to separate the door panels
• Disconnect the wire harness, release the locking tabs, seat the new dispenser evenly, and tighten screws evenly to compress the seal
• Run a short cycle to check for leaks

The Upper Spray Arm is an OEM part for Whirlpool dishwashers. It is located below the upper rack and functions to spray water onto dishes during the wash cycle for thorough cleaning.

Causes of a bad upper spray arm include clogs or mineral buildup that reduce or block water pressure, or physical damage rendering the arm unable to spin properly.

Symptoms of a bad upper spray arm include:

• Dirty or inadequately cleaned upper rack dishes
• Spinning noises or clunking from the wash arm area
• Uneven cleaning results

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Dishwasher Plate-Latch Strike is an OEM part for Whirlpool dishwashers. It is a part that holds the dishwasher door shut during wash cycles. Precise alignment of the strike allows for tight sealing and proper engagement with the door latch.

Causes may arise from normal wear over lengthy use, deformations from repetitive door actions, or incidental damage.

Symptoms of a bad strike can include:

• Door that feels loose and doesn't fully latch closed
• Gaps seen around the door sealing surface
• Water leaks or insufficient drying performance
• Difficulty fully closing or reopening the door

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Center Wash Arm Assembly is an OEM part compatible with Whirlpool dishwashers. It is a multi-spraying component located in the center of the lower dish rack that helps deliver water for superior washing performance. The arm rotates during the cycle to wash all accessible surfaces of dishes.

Symptoms of a bad Center Wash Arm Assembly include:

• Incomplete or inadequate cleaning of dishes, especially those in the lower rack  
• Mineral or hard water deposits building up on dishes
• Reduced water pressure or spray pattern from the wash arm nozzle(s)

Causes of a bad center wash arm can be mineral deposits clogging the nozzle openings over time, or physical damage such as bending or breaking of the arm assembly or its mounting bracket.

This OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers.

The Lower Dishrack Roller Assembly is an OEM part for Whirlpool dishwashers. As an integral component, the lower dishrack roller assembly supports smooth movement and positioning of the lower dishrack. Its precision ball bearings allow for effortless extension and retraction of the lower rack.

Causes of a bad lower dishrack roller assembly can include wear and tear of bearings over time, stripped or damaged rails, or failure of rollers due to excessive loading.  

Symptoms of a bad lower dishrack roller assembly include:

• Difficulty extending or retracting the lower dishrack  
• Noisy or stuck operation of the lower rack
• Rack failing to remain securely in place during wash cycles
• Dishes shifting or falling during wash due to uneven support

This OEM Whirlpool part is also compatible with KitchenAid, Jenn-Air, Amana, Kenmore, and some Maytag and GE dishwashers.