Kenmore 11020232711 Parts

This tub ring mounts at the top of the outer tub to contain splashes and suds during agitation and spin, helping prevent over-the-rim leaks. Replace a cracked or broken ring to restore proper water containment and fit.

• Acts as the upper splash shield for the outer tub
• Helps keep wash water and suds from escaping during operation
• Secures with locking tabs for a tight, even fit around the tub opening
• Typical signs of failure: cracks, broken/missing tabs, water or suds at the top of the tub

• Disconnect power and water; wear gloves and eye protection
• Lift or remove the top/console to access the tub opening
• Release retaining clips/tabs, remove the old ring, and clean the tub rim
• Align and snap the new ring evenly into place; confirm all tabs are fully seated before reassembly

This leveling foot threads into the base of your appliance to support and stabilize it. Adjusting the foot helps level the cabinet, reduce wobble and vibration, and keep doors aligned for smooth, reliable operation. Also called a leveling leg. What it does:

• Provides an adjustable contact point to stabilize the unit on the floor
• Helps level the cabinet so doors align and seal properly
• Reduces rocking, rattling, or excessive vibration on uneven surfaces
• Replaces a cracked, stripped, or missing leveling leg

• 1 leveling foot

• Unplug the appliance and turn off water supply if applicable
• Use a helper to carefully move or tilt the unit; support it securely
• Unthread the damaged foot; thread in the new foot by hand, then fine-adjust with a wrench
• Level side-to-side and front-to-back; ensure all feet make firm floor contact

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

This electronic control board manages oven functions and user interface so the range responds correctly to settings, timers and temperature controls. It restores control logic when the original board is failed or intermittent. What it does:

• Receives user inputs and runs oven control sequences for bake, broil, timers and delays
• Controls display, clock and touchpad responsiveness
• Sends signals to heating elements and relays to regulate temperature
• Common symptom fix: unresponsive controls, blank or erratic display, or intermittent operation

• Disconnect all power at the breaker or unplug the appliance before servicing
• Handle the board by the edges and avoid static discharge; use a grounding strap if available
• Verify the part number on the replacement board matches the original before installation

The Wire Harness is an OEM part for Whirlpool washers. It is responsible for connecting various electrical components within the washer, such as the control board, motor, and sensors, allowing them to communicate and function properly.

A bad wire harness can be caused by several factors, including wear and tear, electrical faults, or physical damage. If you notice issues such as erratic behavior of the washer, error codes appearing on the control panel, or complete failure of certain functions, it may indicate a problem with the wire harness.

Symptoms of a bad wire harness include:

• Intermittent or erratic operation  
• Error codes on the control panel
• Certain functions or cycles not working 

Replace your faulty wire harness with this genuine OEM part to restore your washer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This replacement silverware/cutlery basket holds forks, knives and spoons so small items stay organized during dishwashing and drain properly. It restores a dedicated space for utensils and helps keep the rack tidy. What it does:

• Provides a secure compartment for silverware and small kitchen tools during wash cycles
• Keeps utensils separated to improve cleaning and prevent nesting
• Allows water to drain through while holding items in place
• Replaces a broken, cracked or missing utensil basket to restore functionality

• One replacement silverware/cutlery basket

• No special tools required; typically lifts in and out of the rack—align and set into place
• Inspect for broken tabs or clips on the rack that could prevent proper seating
• Disconnect power to the appliance before performing any repairs or heavy manipulation of racks
• If rack mounting hardware is damaged, replace hardware to ensure the basket sits securely

The Washer Water Inlet Valve is an OEM part for Whirlpool washing machines. This valve controls the flow of water into the washer, opening and closing to allow the correct amount of hot and cold water into the machine during different stages of the wash cycle.

Causes of a bad water inlet valve can include wear and tear over time, sediment build-up, or damage from high water pressure. These issues can cause the valve to malfunction, leading to improper water levels or no water entering the machine at all.

Symptoms of a bad water inlet valve include:

• Washer not filling with water
• Slow fill or no water flow
• Water leaking from the valve area
• Inconsistent water temperature during cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: White. Size: 1 qt. can. Acrylic appliance paint.