Kenmore 66513499N411 Parts

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This diverter disc directs wash water to different spray zones during a cycle, helping ensure alternating spray patterns and thorough cleaning. A worn or damaged disc can cause poor wash performance or incorrect spray routing.

• Routes water from the sump to selected spray arms/zones
• Helps alternate spray to improve coverage and cleaning
• Worn discs may lead to weak spray, poor cleaning, or unusual cycle behavior
• Can contribute to water leaking at the diverter area if the seal interface is compromised

• Disconnect power and water before servicing
• Access is typically from the bottom; remove the toe kick and lower panel as needed
• Note the disc orientation in relation to the diverter mechanism during removal
• Inspect related components (diverter motor/shaft, seals, sump) and replace if worn

This rinse aid knob is the cap for the dishwasher's rinse aid dispenser. It seals the reservoir to prevent leaks and evaporation and provides a secure grip for refilling, helping the dispenser hold rinse aid as designed.

• Covers and seals the rinse aid reservoir opening to contain rinse aid
• Helps prevent leaks or evaporation from the dispenser
• Provides an easy-to-grip cap for removing/reinstalling during refills
• Common symptoms: missing or cracked cap, rinse aid not staying in the reservoir, leaks inside the door, increased spotting from lack of rinse aid

• Disconnect power to the dishwasher before servicing.
• Replace the cap by hand and ensure it seats fully; do not overtighten.
• After installation, run a short cycle to verify proper sealing and no leaks.

This dishwasher detergent dispenser mounts in the inner door and stores both detergent and rinse aid. It releases them at the correct time in the cycle to help deliver consistent cleaning and spot-free results.

• Holds and seals detergent/rinse aid until the control calls for release
• Opens the detergent cup during the wash cycle to dispense soap
• Helps reduce leftover detergent in the cup after a cycle
• Helps with issues like a dispenser door that won't open, soap left after the cycle, or rinse aid leaking

• Disconnect power to the dishwasher before servicing
• Remove the inner door panel to access the dispenser
• Release the locking tabs/screws, clean the sealing surface, and install the new dispenser flush with the door liner
• Reassemble the door and check for leaks before running a test cycle

This heater support holds the heating element securely in place inside the appliance, maintaining correct alignment and clearance for reliable operation. Replacing a worn or broken support helps prevent sagging, noise, or damage from an out-of-position element.

• Secures the heating element to its mounting point to keep it stable
• Maintains proper spacing from nearby components and surfaces
• Helps reduce vibration, rubbing, or rattling noises
• Replace if the original support is cracked, warped, missing, or the element appears misaligned

• Disconnect power to the appliance before servicing; allow hot components to cool
• Access the heater per your model's service information; note the original orientation and routing
• Seat the support fully and handle element leads carefully to avoid damage

This replacement wire restores a reliable electrical path between appliance components. Use it to replace a damaged or heat-stressed lead so power or signal can flow correctly for consistent, safe operation.

• Carries electrical power or signals between components to restore continuity
• Helps resolve issues caused by broken conductors, loose/burned terminals, or brittle insulation
• Can address intermittent operation or components not energizing due to an open circuit
• Ideal when the original lead shows scorching, melting, or corrosion

• Disconnect power (and shut off gas/water if applicable) before servicing
• Document wire routing and connections before removal to ensure correct reassembly
• Transfer any reusable sleeves, clips, or ties from the old lead if present
• Seat connections fully and route the wire away from sharp edges and high-heat areas

This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.

• Fastens brackets, panels, and internal components to their mounting points
• Maintains alignment and reduces vibration during operation
• Replaces missing, worn, rusted, or stripped hardware
• Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position

• Disconnect power; shut off water or gas supply if applicable
• Align the part being secured and remove any damaged hardware
• Hand-start threads to avoid cross-threading; tighten with the correct driver
• Do not overtighten; verify the assembly is secure and operates freely

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

Bushing, Door spring

This small retainer secures the flexible tine-row "comb" on the dishwasher rack. Replacing a cracked or missing clip keeps fold-down tines aligned and stable so dishes load properly and rack parts stay in place.

• Holds the flexrow comb firmly to the dishrack to support adjustable/fold-down tines
• Helps prevent the comb strip from loosening or popping off the rack
• Common symptoms: flexrow won't stay attached, tines collapse or misalign, broken or missing clip
• Restores original rack function and stability

• Disconnect power to the dishwasher for safety
• Pull the rack out and locate the flexrow comb and its retainer
• Release the old retainer's locking tabs (a small flat-blade screwdriver can help), then remove it
• Align and snap the new retainer into place; the tines move and lock as intended

Note: Left Hand side with release lever.

Color: White

This replacement screw secures appliance panels, brackets, and internal components. Install it when original hardware is missing, stripped, or corroded to restore a solid, factory hold and help stop vibration, rattles, and misalignment.

• Provides secure attachment for covers, brackets, and assemblies
• Replaces missing, damaged, or rusted hardware
• Helps resolve loose panels, buzzing/rattling noises, or shifting parts
• Supports proper alignment and reliable operation when tightened correctly

• Disconnect power; shut off gas/water if applicable before service
• Match thread and length to the original; replace in the same location
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If washers, spacers, or threadlocker were present originally, transfer or replace them

This replacement screw secures appliance components, panels, and brackets. It restores a tight, reliable hold when an original fastener is missing or damaged, helping eliminate rattles, gaps, or shifting parts.

• Fastens two or more parts together inside the appliance
• Helps keep panels, brackets, or trim securely in place
• Can reduce vibration, rattling, or loose handles caused by missing/loose screws
• Replaces worn, stripped, or corroded fasteners

• Disconnect power and shut off water supply before servicing
• Match location and orientation to the original fastener
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping or cracking

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey