Kfis29pbms Parts

The Dual Evaporator Assembly is an OEM part for Whirlpool refrigerators. Found within the refrigerator cabinet behind the sidewalls, these dual evaporator coils absorb heat from the refrigerated air and help maintain the optimal cold temperatures needed in each section. 

Symptoms of a bad dual evaporator assembly include:

• Fluctuating or inadequate temperatures in both freezer and fresh food sections
• Frost or ice buildup inside cabinets  
• Increased humidity levels allowing food to spoil faster

Causes can be normal component wear over time, damage to coils from falls/impacts within the refrigerator, or refrigerant leaks decreasing cooling ability. 

This OEM replacement part is also compatible with refrigerator models from brands including Maytag, Jenn-Air, Amana, Magic Chef, and some Kenmore units.

This factory screw fastens appliance components securely. Replacing a missing, stripped, or rusty screw helps stop rattles, keep panels and brackets aligned, and restore a solid, as-designed fit.

• Secures panels, brackets, and trim to the appliance cabinet or frame
• Helps maintain alignment and reduce vibration or rattling noises
• Replaces damaged, corroded, or missing hardware
• Can resolve loose or shifting components

• Disconnect power and shut off gas/water to the appliance before service.
• Use the correct driver; start threads by hand to avoid cross-threading and do not overtighten.
• Install in the original location and match the OEM fastener type specified in your model's parts diagram.

This solenoid is the electromechanical actuator that opens and closes a valve or latch to control flow or movement inside compatible appliances. Replacing a worn solenoid restores reliable on/off operation and responsive dispensing or cycling. What it does:

• Converts electrical signals into mechanical motion to open or close a valve or latch
• Controls water or ice fill cycles, dispenser flow, or other timed movements in the appliance
• Commonly linked to symptoms like no water/ice dispensing, intermittent operation, or a clicking/no-response during a cycle
• Works with the appliance control to ensure precise on/off control where used

• Disconnect power to the appliance before starting any repair
• If the solenoid controls water, turn off the water supply and relieve pressure before disconnecting lines
• Handle electrical connectors carefully; avoid pulling on wires—disconnect at the plug
• Verify correct part fit and function after installation; manufacturer instructions for detailed service procedures

The Bracket is an OEM component specifically designed for Whirlpool brand refrigerators. This bracket is responsible for securely mounting internal refrigerator shelves and bins within the unit. 

Symptoms of a bad bracket can include sagging shelves, difficulty accessing bins, contents spilling or shifting during the opening and closing of the refrigerator door, and excess noise or rattling during compressor operation. 

Causes of a bad bracket include deterioration of mounting hardware over time, cracks or breaks in plastic mounting clips, and loose or faulty assembly.

Symptoms of a bad bracket include:

• Sagging or unsecured shelves   
• Bins that do not stay firmly in place
• Contents spilling out of bins  
• Excess noise and rattling from inside refrigerator

Note: Right side

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a replacement mounting plate that secures and supports internal components for proper alignment and stable operation. Restores structural support and helps maintain correct positioning of nearby parts. What it does:

• Provides a stable mounting surface for adjacent components to prevent movement or vibration
• Keeps parts aligned so mechanisms operate smoothly and reliably
• Replaces a damaged, bent, or corroded plate that can cause rattling or misalignment
• Helps maintain proper spacing to protect wiring and connectors from contact or wear

• Disconnect power before beginning any repair to avoid shock or injury
• Installation typically requires basic hand tools; handle edges carefully
• Inspect nearby fasteners, clips, and gaskets and replace if damaged

This door bumper cushions the door against the frame to prevent metal-to-metal contact. Replacing a worn or missing bumper restores smooth, quieter closing and helps protect surfaces from chips, scuffs, and vibration.

• Absorbs impact where the door meets the cabinet/frame
• Reduces slamming noise and vibration during closing
• Helps protect paint, glass, and trim from wear
• Typical symptoms: missing/cracked bumper, loud clunk when closing, marks on frame, rattling

• Disconnect power and, if applicable, shut off gas/water; allow hot surfaces to cool
• Open the door to access the bumper location
• Remove the worn bumper and clean the contact area for proper seating
• Install the new bumper fully seated and aligned; test door operation

The Valve is an OEM component specifically designed for Whirlpool refrigerators. It regulates the flow of refrigerant through the cooling system.

Causes of a faulty valve can include mineral buildup or debris obstructing flow over many years of use. Internal seals may deteriorate with exposure to refrigerants.

Symptoms of a bad valve include:  

• Increased buzzing or vibrating noises from the refrigeration unit  
• Fluctuating temperatures with foods not staying consistently fresh
• Advanced warming inside refrigerator without cause

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This gasket seals the ice compartment door to help maintain proper cold temperatures and reduce frost or moisture buildup inside the ice storage area. A worn seal can let warm air in and harm ice quality. What it does:

• Seals the ice compartment door to help keep ice cold and dry
• Helps reduce frost buildup and excess condensation inside the compartment
• Can improve cooling consistency and reduce strain on the refrigerator
• Common symptom fix: visible gaps, torn or compressed seal, frost or melting in the ice area

• One ice compartment door gasket

• Clean the door surface and channel before installing to ensure a proper seal
• Press the gasket into the door channel evenly, working around the perimeter for a uniform fit
• If needed, loosen or remove the door per the manufacturer's instructions for easier access
• Avoid sharp tools that could damage the gasket; check the seal after installation and allow time for it to fully seat

This water tube directs water from the dispenser/water system to the appliance's internal components, restoring proper water flow and preventing leaks when the original tube is cracked or clogged. Durable replacement for wet or restricted lines. What it does:

• Routes water from the inlet/valve to the dispenser, icemaker, or internal plumbing.
• Replaces cracked, split, or collapsed tubing that can cause leaks or reduced water flow.
• Helps stop visible pooling or dripping under the cabinet or inside the fresh food section.
• Restores normal water delivery to the dispenser or icemaker when the original tube is obstructed or damaged.

• Disconnect power and shut off the water supply before beginning any repair.
• Inspect fittings and seals; replace any worn gaskets or clamps to ensure a leak-free connection.
• Tighten fittings by hand first, then snug with an appropriate tool—avoid overtightening plastic fittings.
• Test the system at low pressure after installation and check carefully for leaks before restoring full operation.

This front crisper drawer support secures the refrigerator's front crisper drawer for smooth sliding and correct alignment, reducing sagging and sticking so stored items stay accessible and the drawer operates reliably. What it does:

• Holds the front corner of the crisper drawer in place so the drawer slides and aligns properly.
• Prevents drawer sagging, catching, or uneven movement that can make the drawer hard to open or close.
• Helps maintain proper drawer positioning to protect stored produce and prevent rubbing on the cabinet.
• Works with the existing drawer track and rear support.

• Unplug the appliance or disconnect power before starting any service to reduce electrical risk.
• Empty and remove the crisper drawer before replacing the support; follow the refrigerator's parts diagram for correct orientation.
• Inspect the drawer track and rear support for wear; replace any damaged components to restore smooth operation.

Color: Grey

The Drawer Slide Rail is an OEM part for Whirlpool refrigerators. It is designed to allow freezer or refrigerator drawers to glide smoothly in and out. 

Causes of a bad refrigerator slide rail can be wear and tear over long-term use. Accidental damage from overloading a drawer or rough handling can also prematurely wear out slide rails.

Symptoms of a bad slide rail include:

• A drawer that is stiff, sticks, or binds during operation
• Visible damage or bent parts along the slide rail 
• A drawer that no longer fully extends from the refrigerator

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replacement screw that secures panels, brackets, and other components inside your appliance, keeping assemblies tight and aligned. Replace missing or stripped hardware to eliminate looseness, reduce vibration, and restore a solid, factory-fit hold.

• Fastens panels, brackets, trim, or internal components
• Helps maintain alignment and reduce rattling/vibration
• Replaces missing, loose, rusted, or stripped hardware
• Common signs: stripped head/threads, loose panel, buzzing/rattling noises

• Disconnect power before service; shut off gas/water if applicable
• Match to the original screw; start threading by hand to avoid cross-threading
• Use the correct driver size to prevent stripping
• Tighten snugly; do not overtighten. If it won't hold, inspect the receiving hole/clip

This decorative trim piece replaces a damaged or worn exterior trim to restore the appliance's finished appearance and fit. It provides a clean edge and helps cover mounting gaps around the control area. What it does:

• Covers and protects the appliance edge where trim is installed, improving appearance
• Hides gaps between panels and the control area for a finished look
• Replaces cracked, chipped, bent, or missing trim that affects aesthetics
• Prevents sharp or exposed edges that can catch clothing or skin

• Disconnect power (unplug appliance or shut off breaker) before starting any repair
• Typical installation requires removing adjacent screws or clips; have a screwdriver set handy
• Handle edges carefully; trim and surrounding metal can be sharp

This electronic control board is the appliance's main logic module that manages cycles, user controls and display feedback so the unit responds correctly to inputs and runs programmed functions. What it does:

• Receives user commands and sends signals to motors, valves, heaters and timers
• Controls cycle selection, start/stop functions and display indicators
• Can prevent the appliance from starting or cause unresponsive or erratic controls
• Common symptoms: blank or non-responsive control panel, cycles won't start, incorrect cycle behavior or intermittent operation

• Disconnect power before starting; verify the appliance is de-energized to avoid shock
• Take photos of wiring and connector locations before removal for correct reassembly
• Handle the board by edges and avoid static discharge; do not touch components
• Reconnect all harnesses securely and test functions before reassembling trim or panels

A genuine replacement screw used to secure appliance panels, brackets, and components so assemblies stay aligned and stable. Installs quickly with a screwdriver or driver bit to restore proper fit and reduce rattling. What it does:

• Secures panels, trim, brackets or internal components to keep parts properly aligned
• Prevents loose or vibrating panels that can cause noise or wear
• Holds mounting points that keep doors, seals, and assemblies operating correctly
• Replaces stripped, missing, or corroded fasteners that compromise fit

• Turn off and unplug the appliance before starting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or deform parts
• Keep removed hardware organized and replace like-for-like for best fit