Kitchenaid Kdtm404ewh3 Parts

This genuine replacement door handle restores a solid, comfortable grip for opening and closing your appliance's door. Replace a cracked, loose, or missing handle to keep daily use safe and the appliance looking factory-clean. What it does:

• Provides the handhold needed to open and close the door
• Transfers pull force to the door without stressing the latch
• Helps ensure the door can be operated safely and consistently
• Common symptoms: handle cracked, broken, loose, spinning, or missing

• 1 door handle

• Disconnect power before servicing; allow hot surfaces to cool
• Protect surrounding surfaces; support the door if required by your model
• Access the mounting screws as directed by your service manual; note screw locations and any spacers
• Tighten screws evenly without overtightening; wear cut-resistant gloves

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This replacement capacitor stores and releases energy to give an AC motor the phase shift it needs to start and run smoothly. Installing a fresh capacitor can help when a motor hums, struggles to start, or cycles off. What it does

• Provides the phase shift/starting torque an AC motor needs and stabilizes operation
• Helps reduce repeated start attempts and nuisance thermal trips
• Common symptoms of a weak capacitor: motor hums, won't start, or stops shortly after starting
• Physical signs of failure can include a swollen, leaking, or cracked casing

• 1 capacitor

• Disconnect power to the appliance before servicing
• Safely discharge the capacitor with an appropriate resistor/discharge tool before handling
• Mark/photograph wire locations and transfer connections one-for-one to the new part
• Reinstall in the original bracket or mounting location; keep wiring secure and clear of moving parts

This rear support wheel replaces a worn roller that helps a sliding drawer or rack glide smoothly and stay aligned. Restores easy, even movement and reduces dragging, scraping, or tilting during everyday use.

• Supports the rear of a sliding assembly on its track
• Provides smooth rolling action and helps maintain alignment
• Helps prevent binding, popping off the track, or uneven travel
• Replace if the wheel is cracked, flattened, missing, or if movement is noisy or difficult

• Disconnect power before servicing; allow the appliance to cool
• Remove the sliding assembly to access the wheel area
• Transfer or reinstall any axle/retainer from the original wheel as needed
• Verify smooth travel and proper alignment after replacement

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This manifold channels wash water to the dishwasher's spray system for full coverage. Replacing a cracked or warped manifold restores proper water flow and wash performance while helping prevent leaks at the feed connection.

• Directs recirculated water from the pump to the spray arms/feed tube
• Maintains a sealed path to keep spray pressure consistent
• Damage can cause poor cleaning, weak spray, unusual noise, or internal leaks
• Cracks or broken tabs can leave spray arms misaligned or not spinning

• Disconnect power and turn off the water supply before servicing
• Open the tub; remove the lower rack and spray arm as needed for access
• Transfer any seals/O-rings or clips from the old part; seat all connections fully
• Run a short test cycle and check for leaks before reassembling

This factory screw secures components in your appliance to keep them properly mounted and stable during operation. Replacing a missing or damaged screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Fastens panels, brackets, or trim to maintain correct alignment
• Can address rattling, vibration, or loose/misaligned parts where this screw is used
• Helps prevent wear from movement caused by missing or stripped hardware

• Unplug power and shut off utilities before service
• Note original screw location and orientation; replace like-for-like
• Do not overtighten—start by hand to avoid cross-threading
• Address threads before installing the new screw

The Control Board is an OEM part for Whirlpool dishwashers. As the main circuit board for the appliance, it is responsible for controlling all wash functions and cycles.

Causes of a bad control board can include: exposure to moisture, power surges, or simply natural component failure over time.

Symptoms of a bad control board include:

• The dishwasher not powering on at all
• Certain wash cycles not functioning properly
• Error codes displaying
• The control panel display being unresponsive

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

This drain hose channels used water from the appliance's drain pump to the household plumbing. Replacing a cracked, kinked, or clogged hose stops leaks and helps your unit drain correctly at the end of the cycle.

• Directs wastewater from the drain pump to the home drain system
• Helps maintain proper outflow during the drain portion of the cycle
• Common symptoms: standing water after a cycle, water on the floor, drain error codes, visible cracks or kinks in the hose
• Old hoses can become brittle, split, or obstructed over time

• Disconnect power; shut off water supply if applicable
• Place towels or a pan to catch residual water when removing the old hose
• Note original routing; install the new hose without sharp bends or kinks and secure all connections with existing clamps or appropriate replacements
• Run a test drain/cycle and check every connection for leaks

Includes two screws, two clamps, and undercounter mounting brackets.

This insulation pad installs in the factory location to isolate and cushion components or panels. It helps reduce vibration and limit unwanted heat transfer, supporting quieter operation and proper performance where the original pad was installed.

• Provides a thermal and acoustic barrier between parts or panels
• Helps minimize vibration and rattling noises
• Restores proper spacing/cushioning when the original pad is missing or deteriorated
• Replace if the pad is brittle, compressed, contaminated, or falling off
• Common signs include increased noise or rattles and localized hot spots or condensation

• Disconnect power (and gas/water, if applicable) before servicing
• Allow hot or cold surfaces to return to a safe temperature
• Note the original pad's location/orientation; remove old pad and clean the surface
• Install the new pad in the same spot without over-compressing; secure per the original method and verify clearances

The Pump Filter is an OEM part for Whirlpool dishwashers. This filter is a critical component that screens out food particles and other debris from entering the wash and drain pumps. It helps maximize the lifespan of the pumps and ensures efficient circulation of water during each wash cycle.

Causes of a bad pump filter can include clogging over time due to built-up food particles or mechanical damage from hard objects inadvertently entering the filter. 

Symptoms of a bad pump filter include: 

• Reduced or no water circulation in the dishwasher 
• Loud buzzing or grinding noises coming from the pump area
• Leaks emerging from the pump
• Inability to properly fill or drain water

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Nut is an OEM replacement part for Whirlpool dishwashers. It is a small part that secures the kickplate, or the lower front panel of the dishwasher, in place. This nut ensures a secure and tight fit for the kickplate, preventing it from becoming loose or falling off during dishwasher operation. 

A bad nut can occur due to wear and tear, accidental damage, or misplacement. If you notice symptoms such as a loose or wobbly kickplate, or if the kickplate has completely detached from the dishwasher, it may indicate a faulty or missing kickplate nut.

Symptoms of a bad nut include:

• Loose or wobbly kickplate
• Kickplate completely detached from the dishwasher

Restore your dishwasher by replacing the faulty or missing kickplate nut with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

The water inlet is an OEM part for Whirlpool dishwashers. It serves as the water inlet valve, responsible for regulating the flow of water into the dishwasher during cycles. 

Symptoms of a bad water inlet include:

• Inability to fill with water or intermittent filling 
• Leaks or water spray from the inlet area
• Odd sounds like sputtering or crackling from the valve
• Soap residue or film left after cycles from insufficient rinsing

Causes of a bad inlet water valve can include mineral buildup from hard water, stuck or clogged waterways, or mechanical failure of sealing components. Over time and use, inlet valves can degrade leading to improper water distribution. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models.