Kitchenaid Kuds35fxssa Parts

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

12 Ft in length

This cover screw secures an appliance cover or access panel to the cabinet, protecting internal components and reducing vibration. Replace missing, stripped, or corroded screws to keep panels tight and the unit safe and quiet.

• Fastens a cover or access panel to the appliance chassis
• Maintains proper panel alignment and enclosure integrity
• Helps eliminate rattles or buzzing from loose panels
• Typical symptoms: loose/misaligned cover, missing screw, vibration noise

• Disconnect power; for gas/water appliances, shut off supplies before service
• Wear cut-resistant gloves—sheet-metal edges can be sharp
• Align the cover and start the screw by hand to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin metal

Includes two screws, two clamps, and undercounter mounting brackets.

Color: White

This insulation pad installs in the factory location to isolate and cushion components or panels. It helps reduce vibration and limit unwanted heat transfer, supporting quieter operation and proper performance where the original pad was installed.

• Provides a thermal and acoustic barrier between parts or panels
• Helps minimize vibration and rattling noises
• Restores proper spacing/cushioning when the original pad is missing or deteriorated
• Replace if the pad is brittle, compressed, contaminated, or falling off
• Common signs include increased noise or rattles and localized hot spots or condensation

• Disconnect power (and gas/water, if applicable) before servicing
• Allow hot or cold surfaces to return to a safe temperature
• Note the original pad's location/orientation; remove old pad and clean the surface
• Install the new pad in the same spot without over-compressing; secure per the original method and verify clearances

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This factory screw secures panels, brackets, or components within your appliance. Using the correct OEM fastener helps ensure a snug fit and prevents loosening, rattling, or misalignment over time.

• Fastens metal or plastic components to maintain proper alignment
• Helps prevent vibration, noise, and loosened parts
• Common wear item that can strip, rust, or go missing
• Replaces damaged or missing hardware to restore secure mounting

• Disconnect power and shut off water or gas before service
• Note original screw location and orientation for proper reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• If threads are damaged, inspect the mating hole or clip before reuse

Also Order Spray Arm Seal

This replacement utensil basket holds silverware and small kitchen tools upright in the dishwasher so they stay separated for better cleaning and don't fall through the lower rack. Durable plastic design for everyday use. What it does:

• Holds forks, knives, spoons and small utensils upright and separated for improved wash coverage
• Keeps utensils from falling into the wash area or getting trapped under the rack
• Helps reduce rattling and clumping of cutlery during the cycle
• Useful when the original basket is cracked, broken, or missing

• No tools required; slide or drop the basket into the lower rack in the designated position
• Ensure the lower rack is pulled out enough to seat the basket fully and that it sits flat
• Clean basket with mild detergent; avoid harsh solvents or abrasive pads

This replacement screw secures panels, brackets, and other components inside your appliance. Replacing missing or stripped hardware restores a tight, rattle-free fit and keeps parts anchored as designed.

• Fastens metal or plastic panels, brackets, and internal components
• Replaces missing, damaged, or stripped screws
• Helps resolve vibration, rattling, or loose-fitting parts
• Maintains proper alignment and secure mounting points

• Disconnect power and shut off water/gas supplies before service
• Match the screw to its original location; your model's diagram to placement
• Start threads by hand and use the correct driver to avoid stripping
• Do not overtighten, especially into plastic or thin sheet metal

This factory wire harness restores safe, reliable electrical connections inside your appliance. It routes power and control signals between the main control and key components so the unit starts, runs, and responds correctly.

• Distributes power and signals between the control board and components such as motors, valves, heaters, switches, and sensors
• Replaces damaged, brittle, burned, or corroded wiring to eliminate intermittent or failed operation
• Helps address symptoms like no power, won't start, dead or flickering controls, specific functions not working, error codes, or a burnt-wiring odor
• Built with matching connectors and lengths for correct fit and routing

• Disconnect electrical power before servicing; wear cut-resistant gloves
• Photograph existing connector locations and wire routing before removal
• Move any model-specific clips or ties to the new harness; keep wiring clear of sharp, hot, or moving parts
• Seat connectors fully until latched; verify strain relief, restore power, and test operation

This run capacitor helps start and keep the motor running smoothly by providing the necessary phase shift and torque boost. A weak capacitor can cause hard starting, humming, or intermittent motor operation.

• Supplies continuous phase shift to maintain motor rotation
• Helps the motor start reliably under load
• Symptoms can include humming, slow or no start, or overheating shutdown
• Restores normal operation when the original capacitor has weakened

• Disconnect power before servicing; discharge the old capacitor safely
• Note wire locations and transfer leads to the new capacitor one-by-one
• Mount securely in the original bracket or location to prevent vibration
• If the motor still won't start, further diagnosis of the motor or start device may be required

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

This stud is a small mounting fastener that provides a secure anchor point for attaching appliance components. Replacing a worn or missing stud restores a tight, aligned fit and helps prevent looseness, rattles, or shifting.

• Provides a fixed, threaded anchor for mounting a handle, bracket, or panel
• Helps keep parts aligned and secure during normal operation
• Common replacement for studs that are stripped, bent, broken, or missing
• Symptoms can include a loose or wobbly component, difficulty tightening, or visible damage/corrosion

• Disconnect power and, if applicable, shut off water or gas before servicing
• Wear cut-resistant gloves and handle panels carefully
• Hand-start threads to avoid cross-threading; tighten snugly without over-torquing
• Reinstall any covers or related hardware in their original positions