Ksm8990xx Parts

This planetary pinion gear is part of the stand mixer drive system. It meshes within the gear train to turn the planetary assembly, restoring smooth beater rotation when the original gear's teeth are worn, chipped, or stripped.

• Transfers motor torque through the gear train to rotate the planetary/beater hub
• Common fix for grinding or clicking noises from the mixer head
• Helps address slow, intermittent, or no planetary/beater movement
• Useful when inspection shows rounded or damaged gear teeth

• Disconnect power before servicing and remove the mixer's head/gearcase cover as directed by the service guide
• Note gear orientation; clean out old grease and debris before reassembly
• Inspect mating gears, bearings, and bushings; replace any worn components together to prevent repeat failures
• Pack with food-grade mixer grease, seat the gear fully, and verify smooth planetary rotation by hand before powering on

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

This rubber foot replaces a worn or missing foot on the base of a stand mixer. It helps stabilize the mixer, reduce vibration and movement, and protect your countertop so the mixer stays steady during use. What it does:

• Provides non-slip grip to help prevent the mixer from sliding
• Cushions and helps reduce vibration
• Helps keep the mixer level for consistent operation
• Common symptoms include wobbling/rocking, "walking" on the counter, and scuff marks on the surface

• 1 rubber foot

• Unplug the mixer and remove the bowl/attachments before beginning
• Lay the mixer on a padded surface to access the base
• Pull the damaged foot straight out; clean the recess if needed
• Press the new foot fully into the hole until seated flush; replace additional feet as needed to keep the mixer level

This small retainer clip secures the drip bowl and coil surface element so they stay properly seated on the cooktop. Replacing a worn or missing clip restores a tight, level fit and reduces wobble during use. What it does:

• Holds the drip bowl to its mounting point and helps keep the surface element seated
• Maintains alignment to reduce movement and rattling
• Helps prevent the element from tilting so cookware sits more evenly
• Common symptoms: loose or wobbly burner/bowl, bowl won't stay seated, or a cracked/missing clip

• Retainer clip only

• Disconnect power at the breaker before servicing
• Lift out the coil element and drip bowl; note clip orientation for reassembly
• Snap the new clip into place carefully—avoid over-flexing the part
• Reinstall the bowl and element and ensure the burner locks in and sits level

This small retaining pin secures the bowl retainer/clip so the mixing bowl locks firmly in place during operation. Replace it if the original pin is missing or bent, or if the bowl won't stay seated. What it does:

• Anchors the bowl retainer/clip to the frame
• Keeps the bowl locked and stable during use
• Helps reduce bowl wobble, vibration, and rattling
• Common symptoms: bowl won't latch, rocks loose, or visible pin damage/missing

• 1 retaining pin

• Disconnect power before servicing
• Remove the bowl and access the bowl retainer/clip
• Support the casting; drive the old pin out with a small punch—avoid prying against the housing
• Align holes and install the new pin flush; verify the bowl latches securely and adjust the retainer per your model's service guide

This knurled knob provides a secure, finger-grip fastener you can tighten or loosen by hand. It helps hold a panel or component in place without tools, restoring a firm fit and easy adjustment.

• Allows tool-free tightening/loosening of a secured part
• Replaces a missing, cracked, or stripped hand knob
• Helps correct loose or rattling panels due to a worn knob
• Restores proper grip and adjustability

• Unplug the appliance or shut off power before beginning
• Note the original knob's orientation and thread engagement
• Hand-start threads carefully to avoid cross-threading; tighten snugly
• Do not overtighten; verify the secured part is firmly held

This factory mounting screw secures components in place inside compatible appliances, helping maintain proper alignment and reliable operation.

• Fastens panels, brackets, or internal parts to prevent shifting and vibration
• Common fix when a panel or bracket is loose or rattling
• Resolve issues like gaps, misalignment, or buzzing from loose hardware

• Unplug power and shut off utilities before servicing
• Retain and reuse original hardware and clips where applicable
• Start threads by hand to avoid cross-threading, then tighten snugly without over-torquing

Replacement cam that restores proper engagement of the appliance's mechanical linkage so cycles run smoothly. Installs where the drive/shift mechanism needs a correctly timed cam to stop slipping or misalignment. What it does:

• Transfers rotary motion to the linked component so parts engage at the correct time
• Restores reliable engagement to reduce skipping, grinding, or irregular cycle behavior
• Commonly replaced if cracked, worn, or otherwise fails to engage properly
• Matches the OEM part name and fit as a direct replacement when the original cam is damaged

• Always disconnect power (and water, if applicable) before starting service
• Remove required access panels and note the original cam orientation for correct reassembly
• Inspect mating parts (shaft, clips, splines) and replace any damaged hardware before installing the new cam
• Reassemble panels and run a test cycle to ensure normal operation and correct engagement

This factory replacement screw fastens appliance components securely. Use it to replace lost, stripped, or corroded hardware and restore a snug, rattle-free fit and proper alignment of panels and assemblies.

• Secures panels, brackets, and internal components to their mounting points
• Replaces missing or damaged fasteners to maintain correct alignment
• Helps eliminate vibration and rattling caused by loose hardware
• Restores the original fit with OEM-matched threads and dimensions

• Disconnect power and shut off water or gas supplies before servicing
• Use the correct driver bit that matches the screw head to avoid stripping
• Replace one fastener at a time to keep parts aligned
• Tighten snugly; do not overtighten to prevent stripped threads or cracked plastic

Stainless Steel Commercial 11 Wire Elliptical WHIP for 7 and 8 Quart Bowl-Lift Stand Mixers. The Elliptical Wire Whip quickly incorporates air into ingredients for fluffy whipped cream, perfect for whipped egg whites added to frostings and cakes. Fits KitchenAid Stand Mixer models KL26M8, KP26M8, KP26M9, KP26N9, KSM7581, KSM7586, KSM7588, KSM7589, KSM7990, KSM8990, KSMC895, 3KSMC895, 4KSM7990, 5KSM7580, 5KSM7581, 5KSM7586, 5KSM7590, 5KSM7591, 5KSM7990, 5KSMC895, 7KSM7586, 9KSM7990, 9KSMC895.

This mixing beater is the removable paddle that blends and aerates ingredients for stand mixers, restoring even mixing performance and consistent batter or dough texture. It's a direct-replacement style beater sold as a single piece. What it does

• Scrapes, folds and beats ingredients to help produce uniform batter and dough
• Restores proper mixing when the paddle is worn, bent or missing
• Helps eliminate unevenly mixed or lumpy batters and incomplete ingredient incorporation
• Works as the primary mixing attachment for compatible stand-mixer heads

• Unplug the mixer and follow the OEM attachment/removal procedure before installing
• Align and lock the beater onto the mixer hub until it seats securely
• Inspect for cracks, bends or wear before use; do not use a damaged part
• Clean per the manufacturer's care instructions; avoid high-heat/dishwasher use unless OEM specifies

8 Quart Commercial NSF Certified Polished Stainless Steel Bowl with J Hook Handle. 8 Quart KitchenAid Commercial Polished Stainless Steel Mixing Bowl with convenient J Hook Handle is ideal for stacking or hanging. The polished stainless steel mixing bowl is also dishwasher-safe and used with KitchenAid 8 Quart Bowl Lift Stand Mixer models KSM8990, KSMC895, 3KSMC895, 5KSMC895, 9KSMC895.

Cap Hub covers and protects the appliance's hub, restoring a finished appearance and helping keep debris away from internal components. Use when the original hub cap is cracked, missing or visibly worn. What it does:

• Covers and conceals the drive/tub hub for a finished look.
• Helps keep lint and debris away from the hub area.
• Replaces cracked, broken or missing hub caps that expose the hub.
• Check the model-specific diagram for exact fit and orientation.

• Disconnect power (and water if applicable) before beginning any service.
• Part typically snaps or presses into place; the appliance's exploded diagram for the correct removal/replacement procedure.
• Do not force the part; inspect surrounding components and replace any damaged mounting hardware as needed.

This replacement guard is a small protective trim piece that helps shield appliance components and helps keep debris and accidental contact away from internal parts. It restores the appliance's original protection and appearance. What it does:

• Shields nearby components and wiring from accidental contact and debris
• Helps maintain correct airflow paths and component spacing where applicable
• Reduces risk of damage to exposed parts during normal use
• Fits into the factory mounting points to restore original coverage

• Disconnect power to the appliance before starting any repair
• Handle the part carefully; edges may be sharp
• Basic hand tools may be required to remove fasteners and secure the guard