Kucso3ctsso Parts

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

This wave washer is a small, wavy metal retainer that holds rotating or sliding components in place on a shaft. It helps maintain proper alignment and reduces end-play for smoother, quieter operation. What it does:

• Secures components on a shaft to prevent axial movement and maintain alignment
• Helps reduce vibration and rubbing that can cause noise or premature wear
• Commonly used behind agitator, cam, or bearing assemblies where axial retention is required
• Replace if the washer is deformed, cracked, or missing to restore correct component spacing

• Disconnect power before starting repairs
• Remove the affected assembly (agitator/shaft or other specified part) to access the washer
• Install the washer in the same orientation and position as the original; ensure it seats fully
• Inspect surrounding components (bushings, seals, bearings) and replace any worn parts to prevent repeat failure

Bottle with brush. Acyrlic touch-up paint. Color: Empire red. Size: 0.6 fl.oz.

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection

This deodorant is a replacement refrigerator deodorizer that helps reduce common food and household odors inside the fresh-food compartment for a cleaner-smelling interior. Simple swap helps maintain a neutral-smelling refrigerator. What it does:

• Adsorbs and reduces odors in the refrigerator interior to help keep food-smelling fresher
• Fits into the refrigerator deodorizer holder or designated compartment
• Works passively—no power or batteries required
• Helps refresh interior air between routine cleaning cycles

• For best results, remove old deodorizer and place new cartridge in the designated holder
• Disconnect power before beginning
• Wash hands after handling and follow local disposal guidelines for used cartridges
• If odors persist, inspect seals, drains, and spoiled food before replacing the deodorizer

This console flat kit restores the flat control-panel trim on a stove or range for a clean, finished appearance and protection for the controls. Designed as a direct replacement for the damaged or worn console surface. What it does:

• Replaces a cracked, scratched, faded, or missing flat console trim to restore appearance
• Covers and protects the control area from spills, grease, and debris
• Helps ensure proper alignment of front-facing control components and buttons
• Reduces chance of foreign objects entering the control cavity through damaged trim

• Disconnect power to the appliance before starting any work to avoid shock or injury.
• Some models require removing trim screws or control knobs; save and reuse original hardware.
• Align the part carefully with existing mounting points; do not force—check for hidden clips or fasteners.
• Take care around wiring and electronic controls.

Size: 6-32 x 3/8 inch.

This C-shaped retaining ring snaps into a groove on a shaft or pin to hold a component in place. It restores secure retention so parts don't slide off or shift during operation.

• Snaps into a groove to secure parts on a shaft or pin
• Prevents axial movement to keep assemblies aligned
• Helps reduce wobble, rattling, or parts migrating off
• Common signs: missing/broken clip, loose mechanisms, parts slipping off during use

• Disconnect power; also shut off water or gas as applicable
• Wear eye protection—retaining clips can spring free during removal/installation
• Use appropriate snap/retaining ring pliers or a small flat tool; avoid over-expanding the ring
• Ensure the ring seats fully in the groove and replace if bent or fatigued

This handle spacer positions and secures a dishwasher or appliance door handle, keeping the handle aligned and preventing rubbing or binding for smooth door operation. It's a small replacement piece that restores proper handle fit. What it does:

• Provides a stable mounting gap between the handle and door/frame to ensure correct alignment
• Prevents handle contact with the door surface that can cause wear or noise
• Restores proper spacing after a broken, worn, or missing spacer
• Suitable when the handle feels loose, sits crooked, or rubs against the door

• One handle spacer

• Install with the appliance door open on a stable surface; follow the appliance manufacturer's fastening sequence
• Use hand tools only unless the OEM instructs otherwise; avoid overtightening fasteners
• Disconnect power or follow manufacturer safety instructions when required for handle removal

This strike & catch secures the appliance door by engaging the latch so the door stays closed during operation. It restores a positive door stop for safe, reliable sealing and normal cycling. What it does:

• Provides the mating catch for the door latch so the door stays securely closed
• Helps prevent the door from popping open during use
• Can stop symptoms like a door that won't stay closed or intermittent cycle interruptions
• Restores proper door engagement for correct operation and sealing

• One strike & catch

• Disconnect power (and water for refrigerators/dishwashers) before beginning work
• Remove any trim or inner panels as needed; keep fasteners for reassembly
• Install in the same orientation as the original part; secure with existing screws

Bottle with brush. Color: New avocado. Size: 0.6 fl.oz.

Size: 10-16 x 3/8 inch.

A small slotted pin spring used to secure moving parts in appliance assemblies. This compact replacement restores proper retention and alignment where a slotted spring pin is required, helping moving parts stay in place and operate smoothly. What it does:

• Acts as a slotted spring pin to hold shafts, levers or clips in position
• Restores secure retention when original pin is bent, worn or missing
• Prevents excess play or disengagement of connected components
• Helps resolve symptoms like loose or shifting parts, rattling, or components not staying engaged

• One slotted pin spring

• High-level replacement; retains existing mating hardware and holes
• Use proper tools (needle-nose pliers, punches) to remove/install without damaging surrounding parts
• Wear eye protection; pins can release under tension during removal

Size: 8-32 x .312 inch.