Kudmo1tj Parts

A small replacement retainer that secures the FlexRow assembly so the component stays aligned and stable during use. Replacing a worn or broken retainer restores proper positioning and reduces movement. What it does:

• Holds the FlexRow assembly in place to prevent shifting or sagging
• Helps maintain correct alignment for even operation
• Stops clicking, rubbing, or intermittent contact caused by a loose assembly
• Prevents additional wear on adjacent clips or mounts

• Disconnect power to the appliance before beginning any repair
• Removal usually requires releasing adjacent clips or fasteners; basic hand tools may be needed
• Inspect surrounding parts and replace any damaged clips or mounts for a secure fit

This overfill control switch (float switch) senses water level and helps stop the fill valve to prevent overfilling. It replaces a worn or failed water-level safety switch to restore proper fill control and reduce overflow risk. What it does:

• Detects high water level and signals the washer control to stop filling
• Helps prevent water overflow and unintended flooding when working correctly
• Commonly linked to symptoms like continuous filling, overfilling, or washer not advancing cycles
• Interfaces with the washer control board and fill valve to maintain proper water level

• One overfill control switch (float switch)

• Disconnect power and turn off water supply before starting any repair
• Handle connectors gently; confirm wiring positions or take a photo before disconnecting
• Verify proper operation after installation by running a short fill cycle and checking for correct shutoff

This dual positioner assembly helps align and hold the control shaft/knob mechanism so selections register correctly and controls operate smoothly. It replaces a worn or broken positioner to restore reliable selector alignment. What it does:

• Secures and centers the control shaft/knob so detents register properly
• Prevents loose or wandering knobs and helps ensure accurate cycle selection
• Commonly replaced when knobs feel sloppy, skip positions, or controls don't stay set
• Works with the control panel mounting to stabilize selector movement

• Disconnect power to the appliance before starting any work
• Remove the control panel or console to access the positioner per your model's service instructions
• Handle plastic tabs and mounting points carefully to avoid breakage during removal/installation
• Test control function after reassembly to confirm correct alignment and operation

This splash guard seal fits along the dishwasher door to help keep water inside the tub and reduce leaks and drips during cycles. It restores a tighter door seal for more reliable washing performance. What it does:

• Replaces the worn or cracked splash guard seal that lets water escape around the door
• Helps prevent puddles and water on the floor after wash cycles
• Reduces visible leaks and dripping from the bottom/front of the dishwasher door
• Restores the intended door-to-tub barrier to improve containment during operation

• One splash guard seal as shown

• Inspect the door and mounting channel for debris before installing; clean surfaces for a proper fit
• Install by seating the seal into the door/tub channel; no special tools typically required
• If the old seal is brittle or stuck, use gentle prying to remove—avoid sharp tools that can damage surrounding parts
• Disconnect power and water to the appliance before performing repairs; follow all safety guidelines

This inlet water bezel is the trim piece that fits around the washer's water inlet to provide a finished opening and support the inlet connection. It restores appearance and helps position the inlet area for a proper hose fit. What it does:

• Covers and finishes the water inlet opening on the cabinet for a clean appearance
• Helps hold and align the inlet connection and hose to reduce stress on the valve
• Prevents direct contact between the inlet hose/valve and the cabinet edge
• Commonly replaced when the inlet trim is cracked, broken, or worn

• Disconnect power and shut off the water supply before starting
• Remove the appropriate access panel or control console to reach the inlet area
• Handle the bezel carefully to avoid scratching painted surfaces during install
• Re-check inlet hose routing and tighten connections; test for leaks after restoring power/water

Color: Biscuit. Screw for lower toe panel. For black screw use WP302868, for white screw use WP3400836.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Bottle with brush. Acyrlic touch-up paint. Color: Cobalt blue. Size: 0.6 fl.oz.

This Is A Trim Kit For Custom Wood Door Panel Only

Color: Stainless. For black use W10021860. For white use W10021870