Lbrn22514st Parts

Right hand side. For screws use WPW10119828.

Restore dependable cycles with this replacement timer. It controls the sequence and duration of each step, sending power to the correct components at the right time so the machine advances smoothly from start to finish. What it does:

• Directs power to components to run each cycle segment in order
• Advances the cycle through preset intervals
• Helps resolve cycles that won't start or won't advance
• Addresses stopping mid-cycle or only running on certain settings
• Can help when the timer dial doesn't move or advances intermittently

• 1 timer

• Disconnect power before servicing; turn off water supply if applicable
• Access the control console; remove the knob/escutcheon if required and unmount the timer
• Transfer wires one at a time to the new timer or use a photo to match positions
• Reassemble and run a short test cycle to proper operation

This is the washer's agitator assembly with a built-in filter. Replacing a worn or damaged agitator restores proper turnover of clothes and helps capture lint during the wash for cleaner results.

• Drives the back-and-forth wash action that circulates and rolls laundry
• Integrated filter helps collect lint and debris from wash water
• Worn fins or a stripped hub can cause weak or no agitation and poor cleaning
• A missing/damaged filter may lead to excess lint on clothing

• Disconnect power before servicing; turn off water supply for safety.
• Remove the softener cup/center cap; take out the center bolt or retainer if equipped.
• Lift the old agitator straight up; align splines and press the new agitator fully into place.
• Reinstall the fastener and cap; run a short cycle to confirm proper agitation.

This tub ring seal sits between the washer's outer tub and the tub ring. It creates a splash-resistant barrier at the top of the tub to keep wash water contained and help prevent leaks from the cabinet area.

• Seals the perimeter joint between the tub ring and outer tub
• Helps prevent water splashes from escaping during agitation and spin
• May help if you notice water around the lid/top of the cabinet
• Replace when the gasket is torn, brittle, or permanently compressed

• Unplug the washer and shut off the water supply before servicing
• Lift the top or remove the cabinet to access the tub ring (varies by model)
• Remove the tub ring; clean mating surfaces; seat the new seal evenly without twists
• Reassemble and run a short fill/agitate test to check for leaks

White

Color: Almond

This thermostat monitors temperature in the appliance's heating circuit and opens or closes the electrical contacts to control heat and protect against overheating. Replacing a failed thermostat restores consistent heating performance and reliable safety shutoff. What it does:

• Senses temperature and cycles the heating circuit on and off to maintain target heat
• Provides over-temperature protection by opening the circuit if conditions exceed safe limits
• Helps prevent nuisance shutdowns caused by erratic temperature readings
• Common failure symptoms include no heat, inaccurate temperatures, short-cycling, or shutdown during high heat

• 1 thermostat

• Disconnect power (and gas supply if applicable) before servicing; allow all components to cool completely
• Access the thermostat per your service manual; document wire locations and transfer one at a time
• Mount the thermostat securely so the sensing surface/bulb is correctly positioned; avoid kinking or pinching any leads
• After installation, verify proper operation and temperature performance

A shoulder screw that secures appliance components and provides a precise pivot or spacer point. Replaces a missing or worn screw to restore alignment, reduce rattling, and keep panels and assemblies securely in place. What it does:

• Provides a fixed-diameter shoulder for pivots, spacers, or mounting points in assemblies.
• Holds panels and moving components at the correct distance to prevent binding or friction.
• A missing or worn shoulder screw can cause misalignment, rattling, or loose parts during operation.
• Used where a smooth-bearing surface and controlled clearance are required between parts.

• Disconnect power to the appliance (unplug or shut off breaker) before servicing.
• Handle small fasteners carefully to avoid dropping into assemblies; magnetic pickup tools can help.
• Start threads by hand to avoid cross-threading; tighten snugly but avoid overtightening.

Right hand side

Size: .20 Fl. Oz. (6 ml)

Includes suspension pads.

Left hand side.

For mating terminal use WP94614.

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly

Straight knurled pin that secures knobs or small components to a shaft for a tight, slip-resistant fit. Replaces a worn or missing pin to stop loose, wobbly, or spinning knobs and restore reliable engagement. What it does:

• Secures knobs, dials or small parts to control shafts by providing a press-fit, knurled surface.
• Prevents wobble, slipping, or spinning of control knobs that won't turn with the shaft.
• Common service symptom: knob spins freely or fails to engage controls.
• Used where a small metal pin is required to lock a component onto a splined or smooth shaft.

• Disconnect power and unplug the appliance before servicing.
• Remove the knob or access panel to reach the shaft; pin is typically press-fit.
• Removal/installation may require needle-nose pliers, a small punch, or a bench press; protect surrounding parts from damage.
• Keep small parts away from children and follow appliance safety guidelines; replace mating hardware if the shaft or hole is damaged.

Color: White. For black order WP98008545. For biscuit order 98008169.