Lce7804ace Parts

The blower housing seal is a perimeter gasket that closes the gap between the blower housing and the adjoining duct or bulkhead. It keeps airflow contained for efficient operation and helps prevent air leaks and debris from escaping.

• Seals the blower housing joint to minimize air leakage
• Helps maintain proper airflow for consistent performance
• Reduces dust/debris escape into the cabinet or surrounding area
• Replaces torn, brittle, flattened, or missing seals that can cause weak air output or rattling

• Disconnect power; turn off gas supply before servicing.
• Access the blower housing; note the original routing/orientation of the seal.
• Remove the old seal and clean mating surfaces of lint and residue.
• Seat the new seal evenly with no gaps or twists; reassemble and verify airflow.

Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:

• Applies constant tension to the idler pulley to keep the drive belt tight around the drum and motor
• Helps resolve a drum that won't turn or tumbles intermittently
• Addresses belt issues such as slipping off, appearing loose, or premature breakage from low tension
• Can reduce squealing/chirping from the idler area caused by belt slip

• 1 idler spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the idler assembly by removing the front or lower access panel per your model
• Relieve belt tension, unhook the old spring from the idler arm/frame, and install the new spring in the same orientation and holes
• Rotate the drum by hand to check smooth operation before reassembly

Restore visibility inside your appliance. This lamp assembly replaces a damaged or failed interior light so you can clearly see contents when the door opens, helping maintain safe, reliable illumination in the cabinet/drum.

• Provides interior illumination when the door opens or when the control calls for light
• Houses the bulb and makes the electrical connection
• Common symptoms: no interior light, flickering/intermittent light, or heat-damaged/burned socket or housing

• Disconnect power before servicing to avoid electrical shock
• Access the lamp from the interior or service panel per model
• Install a bulb with the correct type and wattage specified for your model
• Test light operation before reassembling panels

A replacement mounting screw used to fasten panels and components in compatible Frigidaire appliances. Replacing a missing or damaged screw restores secure fastening, reduces vibration/rattling, and helps keep parts aligned for reliable operation. What it does:

• Secures panels, trim, brackets or small components to prevent movement and rattling
• Replaces missing, stripped, or damaged fasteners that can cause loose or misaligned parts
• Helps maintain proper fit and finish of appliance panels and access covers
• Useful when a loose screw causes vibration noise or minor part movement

• Unplug the appliance or shut off power at the breaker before servicing electrical appliances
• Use the correct screwdriver or bit to match the screw head to avoid stripping
• Start threads by hand, then tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep small parts away from children and retain any removed hardware for reuse

This lid strike mounts to the washer lid and engages the lid lock/switch when the lid is closed. It signals the control that the lid is shut so the cycle can start and spin safely without interruption.

• Engages the lid lock/switch to confirm the lid-closed status
• Allows cycles to start and spin once the lid is shut
• Typical failure symptoms: washer won't start or spin; lid won't lock; strike is broken or missing
• Restores reliable lid engagement and safety interlock operation

• Unplug the washer before servicing
• Open the lid and remove the damaged strike from the lid (retain any screws if present)
• Align and secure the new strike; ensure it lines up with the lid lock opening
• Close the lid to verify smooth engagement before restoring power

This spring restores tension to the door lock mechanism so the latch returns to its proper position after operation. A worn or missing spring can cause a loose latch, difficulty locking, or a door that won't stay secured during a cycle.

• Returns the door lock latch to its resting position
• Helps ensure the door locks securely during operation
• Symptoms can include a floppy/loose latch, intermittent lock errors, or door not staying latched
• Also helps resolve issues where the door won't unlock smoothly

• Disconnect power before servicing
• Access the door lock assembly per your model's service procedure
• Note spring orientation during removal; install the new spring in the same positions
• Latch operation by gently opening/closing the door before reassembling

A replacement bracket screw used to fasten internal brackets and panels to the appliance frame, restoring secure mounting and reducing rattling or misalignment caused by stripped, corroded, or missing fasteners. What it does

• Secures mounting brackets, panels or trim to the appliance chassis.
• Restores proper alignment and prevents movement or vibration-related noise.
• Use when the original screw is stripped, rusted, broken, or missing.
• Square-drive head provides a reliable engagement for positive tightening.

• Disconnect power to the appliance before servicing to avoid electrical hazard.
• Use the correct square (Robertson) driver to avoid cam-out and head damage.
• Tighten until snug; avoid over-tightening which can strip threads or crack panels.
• If threads are damaged, replace with the matching screw size and type or repair threads before reuse.

This replacement heater assembly restores proper heat output in your appliance. It delivers the thermal energy needed for normal operation so your unit can reach and maintain the correct temperature and complete cycles as designed.

• Generates heat for the appliance's heating/drying/defrost function (as applicable to your model)
• Helps the unit reach and maintain target temperature for proper performance
• Common failure signs: no heat or weak heat; cycles take too long or do not complete
• May trigger heating-related error/fault codes; visible breaks or hot spots on the element; tripped breaker from a short to ground

• Disconnect electrical power before servicing; allow hot components to cool
• Wear cut-resistant gloves; internal panels and chassis edges can be sharp
• Document wire routing and mounting positions before removal; route wiring exactly as original
• After installation, ensure secure connections and clearance from metal surfaces; run a brief test cycle to verify operation

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses airflow through the heat-exchange coils for proper operation
• Supports and aligns the blower wheel so it spins with correct clearance
• Helps minimize vibration and noise when the housing is intact
• Symptoms of a failed housing may include scraping or rattling noises, weak airflow, vibration, or visible cracks/broken mounts around the blower area

• Disconnect power before servicing; wear cut-resistant gloves and eye protection.
• Remove the front panel/cabinet to access the blower section; note screw and clip locations.
• Transfer the blower wheel, seals, and any reusable hardware from the old housing.
• Before reassembly, spin the blower wheel by hand to ensure free, rub-free rotation.

This heater baffle mounts near the heating element to deflect and distribute radiant heat. It helps protect nearby surfaces and wiring while promoting more even temperatures and reliable performance inside the appliance.

• Directs and diffuses heat from the element to reduce hot spots
• Acts as a heat shield to protect the liner and adjacent components from direct radiant heat
• Helps maintain proper clearance and airflow around the element
• Damage or a missing baffle can lead to uneven temperatures, localized discoloration/scorching, or a burning smell

• Disconnect power at the breaker or unplug the appliance; allow it to cool completely
• Access the heater area; remove the screws or clips securing the existing baffle and retain the hardware
• Position the new baffle in the same orientation; ensure it does not contact the heating element
• Restore power and test operation

Evaporator insulator that surrounds the evaporator assembly to reduce heat transfer and help limit frost buildup. Replacing damaged insulation helps maintain consistent temperatures and prevents excess moisture inside the freezer or refrigerator. What it does:

• Insulates and protects the evaporator area — common signs: visible frost or ice buildup and inconsistent cooling.
• Helps reduce vibration-related noise from evaporator components — common sign: rattling or buzzing.
• Prevents cold-air leakage into cabinet walls to support efficient cooling — common sign: warm spots or extended run times.
• Restores proper airflow pathways around the evaporator to help the system cycle normally.

• Disconnect power to the appliance before beginning any repair.
• Access may require removal of interior panels or the evaporator cover; follow OEM service instructions.
• Handle the insulation gently to avoid tearing or compressing it; use only manufacturer-recommended adhesives or fasteners if needed.

This 5 ft, 30 amp 3-wire dryer cord supplies power to compatible electric dryers, replacing a worn or damaged cord to restore safe, reliable operation. Designed for direct power connection to a 3-prong dryer outlet. What it does:

• Carries 240V dryer power through a 3-wire configuration (hot, hot, neutral)
• Replaces frayed, melted or broken dryer cords to eliminate power interruptions
• Helps stop arcing or intermittent power caused by loose or damaged cord connections
• Matches common dryer inlet assemblies that accept a 3-prong cord

• Power must be disconnected at the circuit breaker before replacing the cord.
• Tighten terminal screws fully and route the cord to avoid pinching or contact with heated surfaces.
• Use only if appliance is designed for a 3-prong cord.

This is a suspension spring for select washers. It supports and stabilizes the wash tub during spin and agitation to reduce vibration and noise, helping the machine run smoothly.

• Supports the tub within the cabinet to control movement
• Helps reduce excessive vibration, banging, or walking during spin
• Addresses symptoms like out-of-balance loads, noise, or shaking
• Loss of tension, stretching, or breakage can require replacement

• Unplug the washer and shut off water supply before repair
• Access typically requires removing the top or front panel; support the tub to relieve spring tension
• Wear gloves and eye protection; springs are under tension
• Replace any damaged or missing suspension components in pairs or as required.

This retaining ring secures a shaft or component in-place to prevent axial movement and wear, restoring proper alignment and reducing noise or wobble. It's a small, durable replacement part for assemblies that use a snap-style ring. What it does:

• Holds shafts, bearings or components axially in their mating grooves to prevent shifting.
• Stops rattling, grinding, or excessive play caused by a worn or missing ring.
• Keeps assemblies aligned to reduce premature wear on surrounding parts.
• Provides a simple replacement solution when the original ring is bent, broken, or lost.

• Disconnect power and/or water and remove any panels needed before starting work.
• Use snap-ring pliers or the manufacturer-recommended tool to safely remove and install the ring.
• Inspect grooves and mating surfaces for damage or debris and clean before installing the new ring.
• Wear eye protection and keep fingers clear—snap rings can spring out during removal or installation.

This strike screw secures the door strike/catch to the appliance, keeping the latch aligned so the door closes firmly and any safety interlock engages. Replacing a missing, stripped, or corroded screw helps restore reliable, consistent door latching. What it does:

• Fastens the strike/catch to the door or cabinet
• Maintains proper alignment for positive latch engagement
• Helps address issues like door not latching, loose/rattling door, or intermittent door switch activation
• Replace if threads are stripped, the head is damaged, or the screw is missing

• 1 strike screw

• Disconnect power before servicing; allow hot surfaces to cool. For gas appliances, also shut off the gas supply.
• Support the door or strike and remove the damaged/missing fastener.
• Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening.
• Verify door alignment and latch/lock operation after installation.

A small spring-style hose clamp that secures flexible tubing to fittings to help prevent leaks and hose separation. Replaces a worn or loose clamp to restore a tight seal on water and drain connections. What it does

• Compresses around a hose to hold it firmly on a barbed or smooth fitting
• Helps stop leaks and reduces chance of hose slip-off under pressure
• Commonly used on water, drain, and vent hoses where space is limited
• Simple, spring-action design keeps consistent tension as hoses expand/contract

• Disconnect power and shut off water supply before servicing appliance
• Use pliers to expand the clamp, slide into position, then release to seat it
• Inspect hose and fitting for damage; replace hose if cracked or brittle
• Do not overtighten or modify the clamp; replace with the exact style/size for a proper seal