Lde4000 Maytag Dryer Parts

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This idler bracket spacer sits on the idler arm pivot to maintain proper spacing and alignment in the dryer belt path. Replacing a worn spacer can quiet squeaks and help the drum belt track and tension correctly.

• Maintains correct spacing of the idler bracket on its pivot to prevent side-to-side play
• Helps keep the drive belt aligned on the idler pulley for consistent tension
• Replace if cracked, worn, or missing; possible symptoms include squealing/chirping, belt rubbing or fraying, belt coming off, or intermittent drum rotation
• Useful check: the idler arm feels loose or wobbly, the spacer may be worn

• Disconnect power; turn off gas supply if applicable, and wear gloves
• Access the belt and idler assembly; release belt tension and remove the idler bracket
• Note the spacer's orientation; install the new spacer on the pivot and re-route the belt correctly
• Hand-rotate the drum to ensure smooth belt tracking before reassembly and power-up

This jumper wire links two terminals in the appliance's wiring harness to complete a required circuit. Replace a burnt, broken, or heat-damaged jumper to restore reliable power flow and prevent intermittent operation or arcing at the connection.

• Bridges designated terminals to provide proper continuity per the wiring diagram
• Helps deliver power to the intended component or control
• A failed jumper may cause a component to not energize, no or intermittent heat, or an element/burner that won't operate
• Visible signs of failure include melted insulation, discoloration, or burnt/loose connectors

• Disconnect power at the breaker; turn off the gas supply before servicing
• Follow the tech sheet/wiring diagram; move one connection at a time to the same terminals
• Ensure tight, fully seated spade connections on clean terminals; do not force mismatched sizes
• Route wiring away from sharp edges, moving parts, and hot or high-voltage areas; replace any heat-damaged mating terminals

This jumper wire connects two terminals in an appliance circuit to maintain proper electrical continuity. Replacing a burnt or damaged jumper restores reliable connections so switches, heating elements, and controls receive power as designed.

• Links designated terminals to complete the circuit per the unit's wiring diagram
• Restores continuity when the original jumper or connector is heat-damaged, corroded, or broken
• Visual indicators can include discoloration, melted insulation, or loose spade terminals at the old jumper

• Disconnect power at the breaker/fuse; turn off gas supply if applicable
• Reference the unit's wiring diagram; label/photograph existing connections
• Move one lead at a time; fully seat terminals and match orientation
• Do not use to bypass safety devices; replace any overheated mating connectors

This blower seal sits between blower housing components to prevent air leaks, helping direct all exhaust air through the drum and vent. Replacing a worn seal can help restore proper airflow and drying performance. What it does:

• Forms an airtight gasket between the blower housing and its cover/duct
• Helps maintain correct airflow and temperature balance through the drum and exhaust
• Reduces lint and dust escaping into the cabinet
• Common failure symptoms: longer dry times, weak vent airflow, whistling or rattling from air leaks

• 1 blower seal

• Disconnect power and, for gas dryers, shut off gas before servicing
• Access the blower housing; remove the old seal and clean mating surfaces of lint and residue
• Position the new seal flat and even; reassemble without pinching or deforming the gasket
• After reassembly, verify strong exhaust airflow and check for leaks

The rubber foot is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order W10176519.

This terminal insulator assembly isolates and supports an electrical connection where it passes through the appliance chassis. Replacing a cracked or heat-damaged insulator helps prevent shorts and restores a safe, reliable connection.

• Electrically insulates a live terminal from the metal cabinet or oven wall
• Provides a secure pass-through/mounting point for the element/wire connection
• Helps prevent arcing, shorting, and localized heat damage at the connection
• Typical symptoms: visible cracks or burn marks on the insulator, tripped breaker, intermittent or no heat due to a compromised connection

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the terminal area; label or photograph wiring to ensure correct reassembly
• Transfer wires one at a time; reuse existing hardware if serviceable and tighten connections securely
• Inspect nearby wire ends/connectors and replace any that are heat-damaged or brittle

This 6-foot dryer vent duct connects your dryer's exhaust outlet to the wall vent. It provides a secure path for moist air to exit the home, helping maintain airflow and consistent drying performance. What it does:

• Vents hot, moist air from the dryer to the exterior
• Replaces crushed, torn, or lint-clogged ducting
• Helps address longer dry times, heat buildup/shut-offs, or moisture and lint around the dryer
• Supports a short, direct run to reduce kinks and airflow restrictions

• One 6-foot dryer vent duct

• Disconnect power; for gas models, turn off the gas supply before starting
• Pull the dryer forward and remove old ducting and lint/debris from connections
• Attach the duct fully to the dryer outlet and wall vent and secure with clamps; avoid sharp bends or crushing
• Move the dryer back carefully and confirm strong airflow at the exterior vent hood

This motor clip secures a motor to its mounting bracket or housing, keeping it aligned and stable during operation. Replacing a bent, broken, or missing clip helps stop rattling and prevents the motor from shifting. What it does:

• Retains the motor on its mounting bracket or frame
• Helps maintain alignment to reduce vibration and noise
• Prevents movement that can cause rubbing or wire strain
• Direct replacement when the original clip is damaged or missing

• One motor clip

• Disconnect power before servicing; allow all moving parts to stop
• Access the motor area, note the clip's orientation, and remove the damaged clip
• Seat the motor fully, then install the new clip to secure it to the bracket
• Inspect related mounts/grommets and wiring for wear; verify clearances before restoring power

This clip and insulator assembly secures and electrically isolates a component inside a range or wall oven. It keeps the part firmly positioned while preventing shorts and heat damage, supporting accurate, safe appliance operation.

• Holds the designated component against the oven liner or chassis
• Ceramic insulator provides electrical isolation in high-heat areas
• Maintains correct spacing and alignment for reliable performance
• Replaces a missing, bent, or heat-cracked clip/insulator to stop rattles or arcing

• Disconnect power; allow the appliance to cool fully before servicing
• Wear gloves and eye protection
• Access the mounting point; transfer the component into the new insulator and secure with the clip without pinching wires or capillary bulbs
• Restore power and verify proper operation

This drum baffle mounts inside the rotating drum to lift and tumble laundry during each cycle. Replacing a cracked, loose, or missing fin helps prevent snags and restores proper load movement. What it does:

• Lifts and turns items as the drum rotates to improve tumbling
• Separates garments to reduce tangling and keep loads moving evenly
• Helps prevent small items from lying flat against the drum surface
• Common symptoms include rattling or thumping, visible cracks, clothes snagging/tearing, and reduced tumbling

• One tall drum baffle

• Disconnect power; shut off gas supply before servicing
• Wear cut-resistant gloves; interior cabinet edges can be sharp
• Rotate the drum to access mounting points; support the drum while removing/installing the baffle
• Tighten fasteners securely; hand-turn the drum to verify clearance before testing

Size: 10-32 inch.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

Specs: No.8X1/2 HEX WASHER HEAD

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.