Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fixes excessive vibration and rattling from dryer motor movement. This clamp secures the motor to its bracket, restoring stability. DIY-friendly repair.
Replaced the motor, blower, rear drum felt seal, and drive belt. Vacuumed up the lint everywhere, cleaned extra lint out of the chute, around the blower, and rear vents. Read more
Replace a cracked or missing dryer mounting bracket to keep components securely aligned. Restores support to prevent movement and premature wear.
Disassembled dryer, replaced worn parts and reassembled dryer. Removed top cover, disconnected front connector, removed front panel, removed belt from idler pulley, removed washer drum and belt, replaced push clip, retaining clips, 2 support rollers and idler pulley. Reassembled in reverse order. Read more
Factory protective shield panel for dryer assembly. Guards internal components and directs heat or airflow. Replace if cracked, broken, or missing.
I changed the thermostat and replaced the worn out seals. Read more
Secures the door hinge in place for smooth opening and closing. Replace this small retaining clip if worn, broken, or missing to restore proper alignment.
Removed and replaced start switch then motor, no joy. removed the timer for disassembly, found bad contact. soldered contact to the spring tab and assembled and installed the timer. All good now. Read more
Plastic drum baffle that lifts and tumbles clothes during drying. Replace if cracked, broken, detached, or missing from inside your dryer drum.
I installed it my self by watching your video Read more
Hex head screw for trash compactor assembly. Replaces lost, stripped, or damaged screws during repairs. Essential hardware for securing components.
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more
Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.
It was very easy to fix after watching your video.. Read more
Supports and pivots the hinged dryer top panel for service access. Replace if cracked, broken, or causing wobble, scraping, or alignment gaps.
Installed a new Ignitor & Thermal Fuse. Read more
Dryer won't start or stops mid-cycle? A faulty timer prevents proper cycle advancement. This replacement timer restores reliable operation. DIY-friendly.
REPLACED TIMER. HOWEVER, OLD TIMER HAD A WHITE JUMPER WIRE BETWEEN TWO OF THE TERMINALS. THE NEW TIMER WAS MISSING ONE OF THE REQUIRED TERMINALS. AFTER LOOKING AT TIMERS FROM OTHER WEB VENDORS, I DECIDED I HAD THE ONLY TIMER AVAILABLE. I LOOKED AT THE NEW TIMER AGAIN, AND SAW THAT IT HAD A JUMPER BAR BUILT IN AND THE WHITE JUMPER WIRE WAS NOT NEEDED. I FINISHED INSTALLING THE NEW TIMER, AND THE DRYER WORKS FINE. Read more
Exterior cover that restores your dryer's finished appearance and shields internal components. Replace if cracked, broken, or missing to maintain protection.
Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.
Gray control knob for washer console. Replaces worn, cracked, or missing knobs. Fits timer/selector shaft for accurate cycle and setting selection.
Removed upper cowling swapped out switch. Read more
Touch-up paint for appliances. Covers chips, scratches, and worn areas on range tops, refrigerators, and other appliances. Includes brush applicator.
Ordered 2 infinite burner controls from Appliance Parts Pros and watched the online video on the replacement of them at the same time. When they arrived promptly, I was ready to take on the job. The fix only took about 15 minutes because I was prepared after watching the video. Read more
Lint trap won't slide in all the way or gets stuck? A damaged or obstructed lint chute assembly is usually the cause. Straightforward 30-minute repair.
I replaced the chute and screen - I am very mechanical and have good tools - it took me less than 30 minutes - would take many people longer but it is a straightforward project Read more
Short baffle that mounts inside the dryer drum to lift clothes as the drum rotates. Replace if cracked, broken, or missing for proper tumbling action.
I watched You Tube and it gave me an idea of what was was wrong.. The motor was frozen. There was not room here to comment about the service that I received . It is only one word fantastic, from the time I started chat with the rep to the time I finished. Amazing. I order the part on Tuesday and I received the parts on Wednesday. That night when I came back from work, I fixed . Everybody at home was happy that the dryer was back in business. Thank you guys and the amazing Representative that... Read more
Dryer stops early on auto cycle but works on timed? The moisture sensor control board monitors dryness levels. DIY-friendly repair, 15-20 minutes.
Did some research via the internet and figured the problem was likely the moisture control board. Watched a video of the repair of a similar unit in order to locate the moisture control board. Used the chat feature with one of the Appliance Parts Pros to get a schematic of the dryer and advice about where to use the putty knife to release the springs for access to the board. Thanks to the lady I chatted with for expert advice. Once the actual task was started, the repair took 15 or 20... Read more