Lfx25978st Parts

This cap assembly seals and protects the dryer/refrigeration vent duct where it exits the appliance, helping direct airflow and keep outside air, moisture, and debris out of the duct system. It's a direct-replacement external vent cap. What it does:

• Covers and seals the duct outlet to maintain proper airflow and reduce drafts
• Helps prevent moisture, pests, and debris from entering the duct
• Supports consistent venting to help avoid lint buildup and reduced performance
• Replaces a damaged, cracked, or missing duct cap to restore a proper exterior seal

• One cap assembly for the duct outlet

• Disconnect power and, if applicable, gas before beginning any work
• Remove old cap carefully; wear gloves to protect against sharp edges and lint
• Check and clear the vent path of lint and debris while replacing the cap

This pipe holder is a small plastic clip that secures tubing and small pipes inside the appliance, helping keep lines organized and preventing rubbing or disconnection. It restores proper routing and reduces vibration-related noises. What it does:

• Holds and secures water, drain, or refrigerant tubing to prevent sagging and chafing
• Keeps lines routed away from moving parts to reduce wear and noise
• Helps maintain proper tube alignment to avoid strain on fittings
• Commonly replaced when the original clip is cracked, broken, or missing

• Disconnect power and water before working on the appliance
• Inspect surrounding tubing and fittings for damage when replacing the clip
• Typically installs as a push-fit or snap-on clip; use gentle pressure and avoid forcing
• Replace broken or brittle clips to prevent tubing damage or leaks

This damper assembly controls airflow between compartments to help maintain consistent refrigerator temperatures and restore proper air distribution. It replaces a damaged or stuck damper that interferes with cooling balance. What it does:

• Regulates fresh food/freezer airflow by opening and closing the inlet
• Helps correct uneven temperatures or reduced cooling caused by a stuck or broken damper
• Stops unwanted drafts when the damper is closed
• Operates with the fridge's control system to respond to temperature changes

• Disconnect power to the appliance before starting any repair
• Access typically requires removing interior panels or shelving to reach the damper housing
• Handle plastic parts and wiring gently; avoid forcing connectors

This Door Basket Assembly is the refrigerator door shelf bin that mounts to the inner door. Replacing a damaged bin restores secure, usable storage for condiments and bottles and helps prevent spills and items falling when the door swings.

• Mounts to molded tabs/slots on the door liner to provide shelf storage
• Keeps containers upright and reduces movement during door opening/closing
• Replace if cracked, has broken tabs, won't stay seated, falls off, or is missing
• Restores proper fit and organization on the door

• Empty and support the old bin; lift straight up and out from the door tabs
• Align the new bin with the slots and press down until fully seated
• Confirm the bin is level and locked in place before loading
• Allow cold plastic to warm to room temperature before installation to reduce risk of cracking

This rail guide assembly supports and guides a sliding drawer/rack along its track so it opens and closes smoothly. Replacing a worn or broken guide restores proper alignment and motion, helping prevent sticking, jamming, or uneven travel.

• Supports and stabilizes the drawer/rack on its slide rail
• Helps ensure smooth, straight opening and closing
• Can address issues like binding, noise, or misalignment
• Replaces cracked, warped, or broken guide components

• Disconnect power and, if applicable, shut off water before servicing
• Remove the drawer/rack and retain any reusable hardware
• Install the new guide in the same orientation as the original
• Test movement for smooth travel before fully reassembling

Restore a reliable seal with this door gasket assembly. It forms a tight perimeter around the refrigerator door to keep cold air in, limit moisture and frost at the doorway, and help maintain stable temperatures and efficiency. What it does:

• Seals the gap between the door and cabinet to prevent air leaks
• Helps maintain proper interior temperature and humidity
• Reduces frost and condensation around the door opening
• Common symptoms of a failed gasket: cracks, tears, warping, gaps, sweating around the door, or a door that won't stay sealed

• 1 door gasket assembly

• Disconnect power and wear cut-resistant gloves before servicing
• Let the new gasket relax flat; warming gently with a hair dryer or warm water can remove kinks
• Remove the old gasket and press the new seal evenly into the door channel, ensuring corners are fully seated
• Close the door and check for uniform contact all around (paper-strip test); reseat or adjust hinges/leveling if needed

This refrigerator water tank holds a reserve of water inside the fresh food section so the dispenser delivers a steady, chilled flow. Replace the reservoir if it's cracked, leaking, or internally restricted.

• Stores and chills dispenser water inside the refrigerator
• Helps maintain consistent dispenser flow and pressure
• Damage can cause leaks under drawers or inside the fresh food compartment
• Kinks or blockages can reduce flow or stop water dispensing

• Unplug the refrigerator and shut off the household water supply; dispense water to relieve line pressure.
• Access the tank behind the crisper/deli area; note tubing routing and connection points before removal.
• For push-to-connect fittings, depress the collar to release lines; cut tubing square and fully seat when reconnecting, then perform a gentle tug test.
• Restore water and power, check all connections for leaks, and purge air by dispensing water.

This refrigerator Drawer Tray Assembly forms the shelf/frame that supports a storage drawer. Replacing a cracked or broken tray restores smooth drawer movement, proper support for food items, and organization inside the compartment.

• Supports and guides the storage drawer within the compartment
• Provides a stable, level surface for everyday use
• Replace if the tray is cracked, warped, or has broken tabs
• Common symptoms: drawer binds, drops, misaligns, or won't slide/close smoothly

• Disconnect power before servicing
• Remove the drawer and any items/glass from the area to prevent damage
• Align tabs/rails, seat the tray evenly, and avoid forcing parts together
• Transfer any reusable hardware from the original assembly if required

This guide assembly is a factory-style mounting guide used in TV chassis to position and support internal components, helping maintain correct alignment and stable operation during use and service. What it does:

• Provides a mounting and alignment point for internal TV components to keep assemblies stable
• Helps maintain proper spacing between parts to prevent rubbing, misalignment, or rattling noises
• Can restore correct fit where a damaged or worn guide causes loose panels or shifting components
• Useful when repairing or replacing adjacent parts that rely on the guide for proper positioning

• Guide assembly

• Disconnect power and remove the TV from its wall mount or stand before servicing
• Handle the panel and internal boards carefully to avoid damage; use non-marring tools
• Keep track of all screws and grounding hardware removed during disassembly for reassembly

This tray cover assembly replaces a cracked or missing ice tray cover to keep ice protected and help the ice bin stack and slide correctly. It restores a clean seal and simple access to the ice storage area. What it does:

• Covers and protects ice in the ice bin from odors and debris
• Helps maintain proper alignment and sliding action of the ice bin
• Prevents spills and reduces ice melting caused by gaps or damage
• Commonly replaced when the cover is cracked, warped, or missing

• One tray cover assembly

• Disconnect power to the appliance before servicing to avoid injury
• Remove the ice bin and any remaining ice before installing the cover
• Handle plastic components carefully to avoid cracking; align tabs and slides before seating

This refrigerator shelf assembly is a direct-fit replacement that restores a stable, flat surface for storing food and containers in the fresh-food compartment. Durable glass provides easy cleanup and reliable support. What it does:

• Replaces a cracked, chipped or missing refrigerator shelf to restore usable storage space
• Supports food, containers and small appliance items so contents stay organized
• Helps prevent spills from spreading with a solid, easy-to-clean surface
• Slides into existing shelf tracks or supports to reestablish proper shelving layout

• Remove all items from the shelf area before installing; handle glass carefully
• Typically slides into existing supports or clips—no special tools required for most installs
• If replacing broken glass, wear cut-resistant gloves and clean up shards before installing
• Verify shelf alignment and secure seating in the tracks or clips before returning items to the shelf