Lfx29945st00 Parts

This refrigerator door bin mounts to the inside of the door to hold bottles, jars, and condiments. Replacing a cracked or missing bin restores secure storage and helps prevent items from tipping or falling when the door opens.

• Provides organized, convenient storage on the door for frequently used items
• Attaches securely to molded tabs/rails on the inner door panel
• Helps prevent tipping and spills as the door opens and closes
• Common symptoms: cracked bin, broken locking tabs, won't stay seated, falls off the door

• Unplug the refrigerator or switch off power at the breaker before starting
• Remove contents, then lift the old bin straight up to disengage from the door
• Align the new bin's hooks with the door slots/rails and press down until fully seated
• Verify a snug fit before reloading items

This plastic tube carries water within your refrigerator between internal components. Replacing a brittle, kinked, or leaking line restores dependable water flow and helps prevent drips that can damage interiors, cabinetry, or floors. What it does

• Routes water between internal components (such as valves, filters, reservoirs, and dispensers)
• Helps maintain proper water flow and pressure when intact and unkinked
• Typical failure symptoms: water leaks, slow or no water flow, visible cracks, flattening, or kinks
• Age- or heat-related hardening can cause stress cracks near bends or fittings

• One plastic tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note original routing and clip locations; avoid sharp bends, abrasion points, and hot surfaces
• Insert tube ends fully into their fittings (quick-connect or compression, per design) and gently tug to confirm they're seated
• Restore water, purge air as needed, and check all joints for leaks before pushing the unit back

This Drawer Tray Assembly forms the base/support for a refrigerator drawer. Replace a cracked or warped tray to restore proper fit, stable food storage, and smooth drawer operation.

• Provides a sturdy surface for the drawer and helps keep items contained and organized
• Restores correct seating and alignment so the drawer opens and closes smoothly
• Common failure signs: cracked or bowed tray, broken tabs, drawer wobble, or difficulty sliding

• Disconnect power and remove food from the affected drawer area
• Slide out the drawer; lift out the damaged tray and transfer any reusable trim or hardware from the original
• Seat the new tray fully and reinstall the drawer; do not force or overtighten any clips or screws

The PCB Assembly, Sub is an OEM part for LG refrigerators. It assists the main control board by regulating secondary refrigerator functions such as dispenser controls, ice makers, and temperature displays in specific refrigerator sections. Located inside exterior access panels, the sub board receives inputs and routes outputs behind refrigerator side panels and doors.

Causes of a bad sub board can include water damage to electronic components leading to shorts, as well as failure over many freeze-thaw cycles. 

Symptoms of a bad PCB Assembly, Sub include:

• Ice maker or water dispenser not operating 
• Incorrect temperature reading for sections  
• Error codes appearing on exterior display
• Buzzing or humming sounds from interior panels

This authentic LG replacement ensures all refrigerator features perform dependably. It is also suitable for Sears/Kenmore branded refrigerators containing LG mechanisms and controls. 

This holder bracket replaces a damaged or missing mounting support. It secures an internal component so it stays aligned and stable, helping your appliance operate smoothly without looseness or rattling.

• Provides a rigid mounting point to hold a component or assembly in place
• Maintains alignment to reduce vibration, rubbing, and intermittent operation
• Restores support when the original bracket is cracked, warped, or missing
• Common symptoms include a loose/wobbly part, rattling noises, or visible broken tabs

• Disconnect power to the appliance before servicing
• Note the original bracket's orientation and transfer any clips or screws from the old part
• Use existing hardware and tighten fasteners evenly—do not overtighten
• Verify proper fit and alignment before restoring power

This ice maker lever is the mechanical arm that controls ice production by interacting with the ice maker's on/off and level-sensing mechanism. Replacing a broken or missing lever restores proper operation and helps prevent overfilling or no-ice conditions.

• Acts as the ice maker's shut-off arm to regulate ice production
• Lowers to allow ice making; raises to stop when the bin is full
• Common symptoms: ice maker won't stop making ice, no ice when arm is stuck up, broken/missing lever, lever won't stay in position
• Helps ensure consistent, reliable ice production control

• Disconnect power and shut off water before service
• Remove the ice bin to access the ice maker; gently release the lever from its pivots/linkage
• Note lever orientation; transfer and reuse any original springs, clips, or fasteners
• Reinstall components, restore power, and verify free up/down movement of the arm

This adjustable leveling leg assembly supports and stabilizes your appliance by threading into the base frame. Replacing a worn or missing leg helps you level the unit for smoother, quieter operation on uneven floors.

• Provides height adjustment to level the appliance and distribute weight evenly
• Helps prevent rocking, wobbling, and excess vibration or rattling
• Can improve door alignment and smooth opening/closing when the cabinet is properly leveled
• Useful when a leg is missing, damaged, or threads are stripped

• Disconnect power; if applicable, shut off the water supply
• Use a helper to safely brace or tip the unit; protect flooring when accessing the leg
• Unthread the old leg and hand-thread the new one; tighten as needed
• Adjust front-to-back and side-to-side until stable; all legs bear weight evenly

This is a ring intended for use in refrigerators. The ring is used to adjust the height of the door. Genuine OEM replacement rings are necessary for the repair to ensure a proper fitting.If the refrigerator door no longer opens or closes easily, or if it is not sealing properly, the rings may need to be replaced. Visual inspection can determine if there are problems with the refrigerator door rings. Make sure to unplug the device before starting any of the disassemblies of the machine. Wear gloves.This ring is an authentic OEM replacement part. It is sold as an individual unit. The ring is made of high-quality, durable materials. The replacement piece is sourced directly from the manufacturer. It can be installed in several models of refrigerators. The genuine OEM replacement ring is compatible with refrigerators produced by both LG and Kenmore.

The Filter Assembly, Head is an OEM replacement part for LG refrigerators. As an essential filtration component, the filter head houses the water filter and is responsible for dispensing clean, filtered water through the refrigerator's dispenser. It works to remove contaminants and improve taste.

Causes of a bad filter head can include normal wear and tear over time, mineral buildup within the head that impacts water flow, or damage to the head itself from accidental impact.  

Symptoms of a bad filter head include:

• Reduced or slow water flow from the dispenser 
• Noticeable declines in water filtration effectiveness
• Leaks or water damage around the filter head area

This OEM LG part is also compatible with select Sears/Kenmore brand models.

This door stopper assembly mounts at the hinge to control how far the door opens and promote smooth, consistent closing. Replacing a worn or broken stopper restores proper door swing and helps protect the hinge from overextension.

• Limits the door's opening range to prevent overextension
• Guides and cushions door movement for a smoother close
• Helps maintain door alignment at the hinge area
• Common symptoms: door swings too far, doesn't stop at the usual angle, clicks/binds near the hinge, or visible cracks/wear on the stopper

• Disconnect power to the appliance before servicing
• Support the door and use a helper when loosening hinge hardware
• Note the original orientation and transfer any spacers/shims if present
• Tighten fasteners evenly and verify smooth door operation before finalizing reassembly

The Drawer Cover Assembly is an OEM part for LG French door refrigerators featuring sliding drawer panels. This assembly covers the top edges of the internal crisper and deli drawers.  

Symptoms of a bad drawer cover assembly include:

• Gaps allowing moisture to drip onto contents below  
• Covers difficult or stiff to open and close accompanying drawers
• Cracks or punctures reducing the ability to protect items  
• Covers detaching from their fixed positions   

Causes of failure can be repeated use taking a toll on plastic through daily expansion and contraction, cracks developing from impacts over time, or general wear reducing insulation sealing capabilities.

Replace yours today with this genuine OEM LG assembly to maintain optimal organization and safeguard your stored items.  This replacement part is also compatible with GE and Samsung drawer-equipped refrigerators.

The Magnet Switch is an OEM part for LG refrigerators. It plays an important role in monitoring the position of the refrigerator door. 

The magnet switch works together with a magnet installed in the door gasket to detect when the door is opened or closed. It communicates this information to the control board which uses it to manage temperatures and fan speeds accordingly. 

Causes of a bad magnet switch can include wear and tear over time, physical damage, or failure of internal components. 

Symptoms of a bad magnet switch include:

• Improper cooling and freezing performances 
• Inability to detect when the door is opened
• Erratic temperature fluctuations
• Errors codes relating to door sensors

This genuine OEM LG magnet switch restores the door monitoring functions of your refrigerator. It is also compatible with Sears/Kenmore refrigerator models.

This is a refrigerator door basket that mounts on the inner door liner to hold bottles, condiments, and other small items. Replacing a damaged bin restores secure storage and helps keep items organized and accessible.

• Provides on-door storage space for beverages and condiments
• Helps keep items from tipping or falling when the door opens
• Replace if cracked, broken, warped, or no longer stays seated in the door slots
• Common signs include the bin falling off, visible cracks, or reduced capacity

• Unplug the refrigerator for safety before replacing interior parts
• Lift the old bin up and out of the door liner slots
• Align and press the new bin straight into the slots until fully seated
• Do not overload; distribute weight evenly to prevent future damage

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power

This refrigerator water inlet valve assembly controls and directs the house water supply to the dispenser and ice maker. Replacing a sticking or leaking valve restores proper filling and dispensing and ensures the valve shuts off water reliably.

• Routes water from the supply line to the dispenser and ice maker when energized
• Stops water flow when not energized to help prevent drips, overfilling, or leaks
• Common symptoms of a failed valve: no water at the dispenser, no ice or small cubes, slow/intermittent flow, or leaking near the valve

• Disconnect power and shut off the water supply before servicing
• Dispense water to relieve line pressure; place a towel or pan to catch residual water
• Note/label tubing and wire connectors; push tubes fully into quick-connect fittings and tug gently to confirm they're seated
• Turn water back on and check for leaks, then restore power and run water to purge air from the system

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location