Lgid 2475Qfoa Parts

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser so your appliance makes ice and dispenses water reliably. Replaces a failed valve to restore normal water delivery and prevent leaks. What it does:

• Opens and closes to route household water to the ice maker and dispenser when signaled.
• Stops water flow when the fill cycle ends to prevent overfilling.
• Commonly replaces valves causing no water to the dispenser or ice maker.
• Also used when valve leaks or runs continuously.

• Turn off the refrigerator and shut off the water supply before starting work.
• Disconnect electrical connectors and water lines carefully; expect minor residual water.
• Inspect hose fittings and seals; test for leaks after installation.

This switch assembly restores electrical on/off control for a specific appliance function. Replace a worn or failed switch to stop intermittent operation and return reliable control to the affected circuit. What it does:

• Provides the electrical on/off or function control for the appliance circuit.
• Replaces a failed switch that can cause intermittent operation or unresponsive controls.
• Helps resolve symptoms such as a function that won't start, no response from the control, or erratic switching.
• Connects to the existing wiring harness and mates with the original mounting points.

• Disconnect power to the appliance before beginning any work.
• Remove the appropriate access panel to reach the switch; note wire and terminal locations before disconnecting.
• Unplug the wiring harness or carefully detach terminals, swap the switch assembly, then reconnect securely.
• Restore power and verify the replaced switch operates the function correctly.

The Rack Stop is an OEM part for Frigidaire dishwashers. It serves an important purpose by preventing loaded dishes from shifting forward during wash cycles.

Causes of a bad rack stop can include wear and tear from regularly loading and unloading dishes, as well as minor impacts that cause cracks or breaks. Over time, the mounting screws may also loosen.

Symptoms of a bad rack stop include:

• Dishes shifting forward during wash cycles
• Gaps appearing around the dish rack where dishes are not fully secured
• Noise from dishes banging together or rattling around more than usual
• Potential damage to more delicate dishware

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement sensor assembly that detects appliance operating conditions and sends readings to the control system for proper operation. Installing a working sensor restores reliable feedback and helps resolve related error codes or inconsistent performance. What it does:

• Detects operating conditions and provides electrical feedback to the appliance control.
• Enables the control board to monitor and adjust cycles based on measured readings.
• Faulty or intermittent sensors can cause incorrect readings, error codes, or unstable/incorrect appliance operation.
• Replacing a failed sensor restores accurate sensing and helps return the appliance to normal function.

• Always disconnect power to the appliance before starting work to avoid shock or injury.
• Handle the sensor and wiring gently; avoid pulling on wires or bending sensor probes sharply.
• Ensure connectors are fully seated and routed clear of moving parts or heat sources.
• After installation, restore power and verify proper operation and that any previous error codes are cleared.

This flexible hose routes water between internal components, helping maintain proper flow and leak-free operation. Replacing a worn or cracked hose restores reliable performance and helps prevent water damage inside or beneath the appliance. What it does

• Carries water between components for filling, circulation, or draining
• Maintains a sealed path to prevent leaks when intact
• Deterioration (cracks, hardness) or kinks can restrict flow
• Common symptoms: water leaking, standing water, slow/no drain or fill, moisture odors

• Includes: 1 hose

• Disconnect power and turn off water supply before service
• Place towels or a pan to catch residual water during removal
• Note the original routing and transfer any clamps/seals; replace if worn
• Push hose fully onto fittings, route to avoid kinks, and test for leaks after reassembly

Color: Black

Flapper seals the appliance drain/valve to prevent leaks and ensure proper water flow. Replacing a worn or damaged flapper restores reliable sealing, reduces dripping, and helps the appliance drain correctly. What it does:

• Seals the drain/valve opening to stop water leaks
• Opens and closes to allow normal draining during cycles
• Restores a watertight seal when the original flapper is cracked, torn, or warped
• Can resolve slow draining, intermittent leaks, or pooling at the base

• Disconnect power and shut off the water supply before starting any repair
• Handle the part carefully; avoid stretching or nicking sealing surfaces
• Clean the mating surfaces and follow the appliance's service manual for removal/installation

This fixing clamp secures small components to the appliance frame to reduce movement and rattling. Replacing a worn or missing clamp helps keep hoses, wiring and trim properly held for quieter, safer operation. What it does:

• Secures hoses, wiring, panels or small parts to a mounting point to prevent shifting
• Reduces vibration and rattling caused by loose or damaged fasteners
• Keeps components aligned to help avoid chafing or accidental disconnection
• Use when the original clamp is cracked, broken, bent, or missing

• Always disconnect power (and water, if applicable) before servicing the appliance
• Access often requires removing trim or a cover; common hand tools include screwdrivers and pliers
• Ensure the clamp fully seats around the component and engages the mounting feature or fastener
• Inspect adjacent wiring, hoses and mounting surfaces for damage and replace any compromised parts

This is a replacement lower spray arm for dishwashers. It rotates to direct pressurized water across dishes, restoring proper spray coverage and improving cleaning performance. What it does:

• Delivers rotating, pressurized water to rinse and clean lower-rack dishes
• Replaces worn, cracked, or clogged spray arms that reduce washing effectiveness
• Helps stop symptoms like poor cleaning, leftover food on plates, or uneven wash cycles
• Works with existing spray arm hub and fastener when undamaged

• One lower spray arm

• Disconnect power and water supply to the dishwasher before servicing
• Remove lower rack and inspect hub/fastener for damage before installing the new arm
• Install and secure the spray arm per your dishwasher's service instructions; ensure it spins freely
• Run a short wash cycle to verify proper rotation and that no leaks or unusual noises occur

The Adjustment is an OEM part for Frigidaire dishwashers. This part plays a key role in finely tuning the overall cleaning and drying performance of the appliance. 

The adjustment controls parameters like wash and rinse water pressure, wash times, and temperature control. Problems occur through normal wear or if the adjustment is inadvertently changed. 

Causes of a bad adjustment can include stripped or worn-out adjustment mechanisms that no longer work as intended. Improper calibration reduces cleaning power.

Symptoms of an improperly adjusted dishwasher include:

• Inadequate removal of soil from dishes   
• Dishes not drying completely  
• Excessive noise or vibration during operation
• Faulty temperature readings inside the unit

Replacing the adjustment component with this OEM Frigidaire part restores factory settings for optimal cleaning. This replacement is also compatible with dishwasher models manufactured by Electrolux, Westinghouse, and some KitchenAid models.

This spray arm circulates pressurized water to clean dishes by directing spray across the rack. Replacing a damaged or clogged spray arm restores proper water distribution for more consistent wash performance. What it does:

• Rotates and delivers water to clean dishes and glassware during wash cycles
• Helps maintain even coverage across the dishwasher rack for better cleaning
• Can cause poor wash results, visible spots, or debris left on dishes when cracked or clogged
• Worn or broken spray arms may rattle or fail to rotate during operation

• One spray arm

• Disconnect power and water supply before beginning any repair
• Remove the lower and/or upper rack as needed to access and replace the spray arm
• Inspect mounting hub and seals; replace any worn clips or gaskets per manufacturer guidance
• Test a short cycle after installation to confirm rotation and proper spray pattern

This O-ring is a small rubber sealing ring that restores a watertight seal at a connection point to help stop leaks and prevent water damage. It's a simple, low-cost part used where two parts meet. What it does

• Seals joints to prevent water leaks at valve, hose or fitting connections
• Stops dripping or pooling caused by a damaged or worn seal
• Helps maintain proper flow and pressure by keeping connections tight
• Works wherever the OEM specifies this exact O-ring size and shape

• Disconnect power and shut off the water supply before servicing
• Replace only with the exact O-ring size specified by the OEM for a proper seal
• Inspect mating surfaces and clean debris before installing the new O-ring
• Lubricate with a small amount of food-grade silicone lubricant if OEM guidance recommends it; avoid petroleum-based lubricants on rubber seals

The Tubing is an OEM part for Frigidaire dishwashers. As a key component of the spray arm assembly, the tubing works to distribute water throughout the dish rack during wash and rinse cycles. 

Causes of bad tubing can include mineral or limescale buildup reducing water pressure over time. Cracks or kinks from constant bending also jeopardize tubing integrity.

Symptoms of damaged tubing include:

• Poor or uneven spray pattern across the dish rack
• Reduced water pressure noticed during cycles  
• Leaks at tubing connections

Replacing the tubing restores the proper water flow needed for thorough cleaning. This OEM Frigidaire part replaces both the tubing segment and needed clamps/fasteners for hassle-free installation. It is also compatible with dishwasher models by Westinghouse, Crosley, and KitchenAid.

This genuine refrigerator water tank stores and supplies water to the dispenser and ice-making system, restoring normal water flow and reducing leaks from a damaged reservoir. It fits behind the front grille or inside the cabinet depending on model. What it does:

• Holds and channels water for the dispenser and icemaker, maintaining proper supply
• Replaces cracked, leaking, or warped reservoirs that cause visible leaks
• Restores normal dispenser flow when a damaged tank restricts water delivery
• Prevents intermittent filling issues caused by a compromised reservoir

• One water tank/reservoir

• Disconnect power and shut off the water supply before starting
• Handle carefully to avoid damage to fittings and seals during removal/installation
• Inspect and replace any worn gaskets or tubing connections for a leak-free seal

This door latch secures the appliance door in the closed position to help maintain proper sealing and operation. It replaces a worn or broken latch so the door stays shut reliably during use. What it does:

• Secures the appliance door to prevent accidental opening during cycles or when moving the appliance
• Helps maintain an effective door seal to support proper temperature control and operation
• Stops common symptoms like a door that won't stay closed or that pops open unexpectedly
• Functions as the mechanical catch that engages with the strike or frame when the door is closed

• One replacement latch

• Disconnect power to the appliance before beginning any repair
• Basic hand tools are typically required; remove trim or access panel if necessary to reach the latch
• Handle small plastic components carefully to avoid breaking tabs or mounting points
• Verify correct latch orientation and engagement with the door strike before reassembling

This electronic control board replaces the refrigerator's main user interface control, restoring reliable temperature management and cycle sequencing. It lets the appliance receive user inputs and run timed defrost, compressor, and fan operations. What it does:

• Houses the control circuitry that manages cooling cycles, defrost timing and fan/compressor operation
• Responds to user input from the front control panel and translates commands to the appliance systems
• Can stop or reset erratic cycling, display control errors, or fix non-responsive controls when the board is faulty
• Common symptom: unresponsive control panel, incorrect temperatures, or failure to start compressor or defrost cycle

• High-level replacement only — disconnect power before accessing electrical components
• Handle the board by its edges and avoid static discharge; use an anti-static wrist strap if available
• Verify connectors are fully seated and wiring matches original locations before restoring power