Lgrc2699tt Parts

This factory fastener secures panels, trim, or brackets on your appliance. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned for proper operation and a clean, finished appearance.

• Fastens exterior panels, trim pieces, or internal brackets to the appliance chassis
• Replaces lost, damaged, or stripped hardware
• Helps prevent vibration, rattling, and gaps between parts
• Common signs you need this screw: missing hardware, loose or misaligned panel/trim, stripped head or threads

• Disconnect power before servicing; also shut off the gas supply
• Use the correct driver; start the screw by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping or cracking adjacent parts
• Repair or replace the mounting point before installing

This burner assembly restores proper gas flame and heat in your dryer. It directs and mixes gas and air for clean ignition at the igniter, helping clothes dry efficiently and consistently.

• Provides the flame path and mixing chamber for gas ignition
• Helps resolve symptoms like no heat, intermittent heat, or very long dry times
• Can address issues where the burner won't ignite or the flame will not stay lit
• Designed to fit the factory burner mount and align with the igniter and flame sensor

• Disconnect power and shut off gas supply before servicing; allow the appliance to cool
• Access is typically from the front lower panel or burner compartment
• Transfer any reusable hardware from the original assembly if required
• After reassembly, restore gas and check all connections for leaks using a soapy water solution

This top hinge supports the hinged top or upper panel, allowing it to lift for service and close securely. Replacing a worn hinge restores smooth motion and proper alignment to help eliminate wobble, scraping, or gaps.

• Provides the pivot point for lifting the top/panel
• Maintains alignment and helps the top seat flat when closed
• Restores smooth opening/closing without binding or rubbing
• Common signs of failure: loose or uneven top, squeaks, difficulty lifting/closing, visible bending or cracks at the hinge

• Disconnect power; also shut off gas and allow all surfaces to cool
• Support the top/panel while removing and installing the hinge to prevent strain
• Transfer and tighten existing mounting screws unless new hardware is provided
• After installation, check alignment and clearances; replacing hinges in pairs can improve fit

This small spacer fits on the idler assembly shaft to properly space and align the belt tensioner. Replacing a worn spacer helps keep the drive belt tracking correctly so the drum/tub runs smoothly and quietly. What it does:

• Spaces and centers the idler pulley on its shaft
• Helps maintain proper belt alignment and tension
• Can reduce squeaking or chirping from the idler area
• A worn or missing spacer may let the belt ride off, fray, or stop the drum/tub

• 1 idler spacer

• Disconnect power before servicing; let hot components cool
• Access the idler assembly per your model, relieve belt tension, and remove retaining hardware to slide off the pulley and old spacer
• Install the new spacer in the same location/orientation; reassemble and route the belt correctly
• Rotate the drum/tub by hand to verify smooth belt tracking before restoring power

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

This replacement cover restores the appliance's finished appearance and protects internal components from dust and debris. It's a direct-fit exterior trim piece designed to replace a cracked, broken, or missing cover. What it does:

• Protects internal components and wiring from debris and accidental contact
• Restores the appliance's cosmetic appearance and helps maintain sealing
• Helps reduce dust buildup in the covered area
• Replaces damaged or missing trim that can expose sharp edges or hardware

• Disconnect power (unplug or switch off circuit breaker) before beginning work
• Basic hand tools may be required; follow for panel removal/replacement
• Handle carefully to avoid scratching the finish and watch for sharp edges
• Replace with manufacturer-recommended fasteners

Color: Black. For biscuit order 98008169. For white order WP98008544.

This replacement terminal box encloses the dryer's rear power-cord connection area. It shields the terminal block and wiring to help prevent arcing and heat damage, supporting safe, reliable operation.

• Houses and protects the terminal block and cord connections at the rear of the dryer
• Provides mounting points for the cord strain relief and cover
• Helps contain heat from loose/overheated connections to reduce risk of damage
• Damage here can contribute to scorching/melting at the cord entry, tripped breakers, or intermittent/no power

• Disconnect power before servicing; for gas dryers, also shut off gas supply
• Access the rear terminal area and document wire routing before disassembly
• Install the new box using existing hardware; transfer wiring and reattach the cover/strain relief
• Tighten terminal screws securely and verify correct cord configuration before testing

This left-hand hinge assembly supports and pivots the appliance door or lid so it opens and closes smoothly and stays aligned for a proper seal. Replacing a worn hinge can correct sagging, rubbing, and hard-to-close doors. What it does:

• Provides the pivot point and support on the left side of the door or lid
• Maintains alignment to help ensure proper latch engagement and gasket contact
• Restores smooth opening/closing and reduces binding or scraping
• Common symptoms of a bad hinge: door droops, squeaks/grinds, rubs the cabinet, won't close flush, or shows visible play/damage

• 1 left-hand hinge assembly

• Disconnect power (and shut off water, if applicable) before servicing
• Support the door/lid while removing fasteners to prevent dropping or damage
• Transfer any original screws, bushings, or trim pieces as needed
• After installation, adjust mounting as needed for smooth operation

This gray control knob replaces a worn or broken knob on the console so you can accurately select settings. It fits onto the timer/selector shaft and restores a secure grip with smooth, positive engagement. What it does:

• Attaches to the control/timer shaft on the front panel
• Lets you turn and select cycles or options
• Restores a snug fit when the original knob is cracked or stripped
• Common symptoms: knob spins freely, falls off, won't turn settings, or is missing

• 1 gray control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; retain any insert/clip used by your model
• Align the new knob with the shaft and press firmly until fully seated
• Test all settings for proper engagement

This burner orifice meters gas to a range/cooktop burner through a calibrated opening. Replacing a clogged, damaged, or incorrect-size orifice helps restore proper flame height and clean, consistent combustion for reliable cooking performance.

• Regulates fuel flow to the burner via the precisely sized orifice opening
• Helps address weak/uneven flame, yellow or sooty flame, or delayed ignition
• Replaces stripped, blocked, or wrong-size orifice spud
• Size- and position-specific—match the stamped size and location

• Disconnect electrical power and shut off the gas supply before servicing
• Allow the cooktop to cool; remove grates, caps, and burner head to access the orifice holder
• Use the proper orifice/nut driver; do not overtighten or alter/enlarge the opening
• After reassembly, restore gas and leak-test with an approved solution; verify a stable blue flame and adjust air shutters if applicable

This replacement ice chute directs ice from the bucket to the dispenser opening, helping prevent jams and stray cubes. If the original chute is cracked, warped, or obstructed, replacing it restores smooth, consistent ice dispensing. What it does:

• Guides cubed or crushed ice through the dispenser opening into your glass
• Helps prevent ice from scattering or missing the glass
• Reduces ice jams and clogs caused by damaged or misaligned parts
• Common symptoms: ice not dispensing properly, ice spilling at the dispenser, frost or ice buildup in the chute area, broken plastic pieces

• 1 dispenser ice chute

• Unplug the refrigerator and turn off the water supply before servicing
• Access the dispenser area per your model's service instructions
• Note orientation; transfer any gaskets/seals and reuse original hardware if applicable
• Ensure the chute seats and aligns correctly with the ice door before reassembly and test

This replacement blower wheel restores proper airflow by moving air through the appliance's blower housing and out the exhaust. A worn or stripped wheel can cause weak ventilation, vibration, and noisy operation.

• Attaches to the motor shaft and spins to move air through the blower housing and ducting
• Maintains steady airflow for efficient appliance performance and ventilation
• Typical failure signs: reduced airflow at the exhaust, rattling/scraping noises, wobble on the shaft, or cracked/missing fins
• Helps resolve vibration from an out-of-balance or damaged wheel

• Disconnect power; turn off gas supply before servicing
• Access the blower housing; remove debris and inspect seals before installation
• Transfer any reusable retainer, nut, clip, or set screw from the old wheel as required by your model
• Seat the wheel fully and secure per your model design (e.g., reverse-thread, retainer, or set screw); verify free rotation and clearance before reassembly

This drawer roller supports and guides the lower range drawer so it slides smoothly on its track. Replacing a worn or broken roller restores easy operation and helps prevent the drawer from binding, sagging, or coming off the track.

• Supports the storage/warming drawer as it opens and closes
• Helps keep the drawer aligned on the rails to prevent tilting or popping off
• Reduces friction for smoother movement and less noise
• Typical failure signs: sticking drawer, rough/grinding movement, sagging front, or a cracked/flat-spotted wheel

• Disconnect power and allow the appliance to cool completely
• Remove the lower drawer to access the rollers
• Detach the fastener or retainer, install the new roller in the same orientation, and secure it
• Reinstall the drawer and verify smooth travel and proper engagement on both tracks

Restore visibility inside your appliance. This lamp assembly replaces a damaged or failed interior light so you can clearly see contents when the door opens, helping maintain safe, reliable illumination in the cabinet/drum.

• Provides interior illumination when the door opens or when the control calls for light
• Houses the bulb and makes the electrical connection
• Common symptoms: no interior light, flickering/intermittent light, or heat-damaged/burned socket or housing

• Disconnect power before servicing to avoid electrical shock
• Access the lamp from the interior or service panel per model
• Install a bulb with the correct type and wattage specified for your model
• Test light operation before reassembling panels

Color: White.