Lrflc2706s /00 Parts

This replacement shelf assembly restores a flat, secure storage surface in the fresh food compartment. It replaces a damaged or missing shelf so items stay organized and supported, seating into the factory rails for a stable, level fit. What it does:

• Provides a level platform for food storage in the refrigerator section
• Fits and locks into the shelf rails/brackets for proper support
• Replaces cracked, broken, sagging, or loose shelves
• Restores lost capacity when a shelf is missing or unsafe to use

• 1 refrigerator shelf assembly

• Unplug the refrigerator and clear items from the shelf area
• Carefully slide the old shelf out of the side rails; retain any hardware reused by your model
• Position the new shelf in the rails; insert the rear edge first, then lower the front until fully seated
• Handle carefully and confirm the shelf sits flat and secure before loading items

This replacement door gasket creates a tight seal around the refrigerator door to help keep cold air in and warm, moist air out. Restores proper sealing to help maintain temperature and reduce frost or moisture buildup. What it does:

• Seals the refrigerator door to maintain consistent internal temperatures
• Helps prevent moisture, frost, and condensation inside the fresh-food compartment
• Reduces air leaks that can cause the fridge to run more frequently or uneven cooling
• Common symptom: visible gaps, torn or compressed seal, or moisture/frost near the door edge

• Disconnect power to the appliance before starting any work.
• Remove the old gasket carefully; inspect and clean the gasket channel and mating surface before installing the new seal.
• Warm the gasket slightly or work around the perimeter to seat it evenly; avoid overstretching.
• If clips or adhesive are used on your model, reuse or replace only the exact fasteners specified by the manufacturer.

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly

This DC motor drives the refrigerator's circulation fan, moving air across the coils and through the compartments for steady, efficient cooling. Replacing a weak, noisy, or seized motor restores airflow and temperature stability. What it does:

• Converts DC power into rotation to spin the attached fan and promote airflow
• Supports efficient heat exchange for even compartment temperatures
• Common symptoms: fan not running or intermittent, loud humming/squealing/grinding, warm spots or frost buildup, longer run times
• Contributes to reduced ice production or error codes in some models

• 1 DC motor

• Disconnect power and wear cut-resistant gloves; internal panels may have sharp edges
• Access the motor behind the interior panel or rear service panel; note connector orientation and wire routing
• Transfer the fan blade, grommets, and any mounting hardware from the old motor if needed
• Seat the blade fully and verify it spins freely before reassembly and restoring power

This sensor PCB assembly detects and relays sensor signals to the appliance control system, restoring accurate sensor feedback and communication when the original sensor board fails or malfunctions. Designed as a direct replacement board. What it does:

• Reads sensor inputs and converts them to signals the main control board can interpret.
• Replaces a failed or intermittent sensor board that causes incorrect readings or sensor-related error codes.
• Can resolve symptoms such as unexpected sensor faults, control errors, or appliances not responding to sensor changes.
• Matches the OEM board function; verify model compatibility before ordering.

• Always disconnect power before servicing to avoid shock or shorting the board.
• Use ESD precautions and handle the PCB by its edges to prevent static damage.
• Ensure all connectors are fully seated and the board is mounted in the original orientation.

This display case is the outer housing that holds and protects the appliance control panel and display assembly. It restores a clean finished appearance and shields the electronics from dirt and accidental contact. What it does:

• Houses and secures the control board, display lens and user interface components
• Protects the display and electronics from dust, spills and physical damage
• Restores a solid, aligned control panel if the original housing is cracked, warped or loose
• Improves readability and the appliance's finished appearance

• Disconnect power to the appliance before starting any repair.
• Typically fastens with screws or clips; keep hardware and alignment tabs for reassembly.
• Handle the display lens and electronic connections gently to avoid damage.

This dispenser lever is the replacement actuator that presses the ice/water switch so your refrigerator dispenses on demand. Restores proper contact and smooth push action for reliable dispensing. What it does

• Acts as the user-facing lever you press to activate the ice or water dispenser
• Re-establishes firm, consistent contact with the dispenser switch when the original lever is cracked, loose, or broken
• Stops intermittent dispensing caused by a worn or misaligned actuator
• Matches the OEM shape for correct alignment and smooth operation

• Turn off power to the refrigerator or unplug it before starting work
• Most installations are screw- or snap-style; remove the dispenser bezel to access the lever
• Handle plastic components gently to avoid cracking; use trim tools if needed

A momentary push-button switch that restores reliable button control on the appliance console. Replaces a worn or non-responsive push switch so the control board receives a clear input when the button is pressed. What it does:

• Sends a momentary electrical signal to the control board when pressed
• Replaces broken, stuck, or intermittently working push buttons
• Helps resolve symptoms like no response from the console, intermittent button function, or a physically damaged button
• Functions as the user input for single-press commands

• One momentary push switch

• Disconnect power before servicing to avoid shock or injury
• Access usually requires removing the control panel or console; use appropriate screwdrivers
• Note connector orientation and gently unplug wire harness—do not pull on wires

This center hinge assembly replaces the refrigerator door center hinge to restore proper door alignment and smooth operation. It supports the door weight and helps maintain correct sealing for reliable cooling performance. What it does:

• Supports the center of the door, keeping it aligned and preventing sagging
• Provides the pivot point for smooth opening and closing
• Helps maintain a consistent door seal to prevent cool-air loss
• Can eliminate shifting, squeaking, or uneven door gaps caused by a worn hinge

• 1 center hinge assembly

• Disconnect power and empty or support the door before removing the hinge
• Use appropriate tools and a second person to safely support the door during replacement
• Inspect adjoining hinges and mounting hardware; replace any damaged fasteners for best results

This Magic Room cover is the replacement shelf panel that closes and protects the refrigerator's Magic Room compartment, keeping foods separated and organized for easy access. What it does:

• Replaces a cracked, chipped or missing Magic Room shelf panel
• Provides a flat surface over the Magic Room compartment to support containers and produce
• Helps keep items separated from the drawer below for better organization
• Restores proper fit and appearance inside the refrigerator

• Remove any items and the Magic Room drawer before installing the cover
• Align the panel with the shelf supports and lower into place until it snaps or seats securely
• Handle carefully to avoid chipping or scratching the plastic

This replacement cover is an exterior access panel that protects internal components and restores the appliance's finished appearance. It keeps wiring and mechanisms enclosed while maintaining the cabinet's original look. What it does:

• Covers and protects internal components from dust, spills, and accidental contact
• Restores the appliance's cosmetic appearance when the original cover is cracked, chipped, or missing
• Helps maintain proper airflow routing and component spacing behind the panel
• Prevents small objects from entering service areas that could cause damage

• One replacement cover

• Disconnect power and water before starting any repair
• Remove fasteners or release retaining clips holding the old cover; keep hardware if re-using
• Align the new cover carefully and secure with the original screws or clips; do not force into place
• If clips or mount points are damaged, replace them before finishing installation

The Power Cord Assembly is an OEM replacement part for LG refrigerators. It includes the electrical cord and strain relief that links the refrigerator to an external power source.  

This power cord assembly safely delivers electricity from the wall outlet to the internal compressor and fan modules. It facilitates proper cooling functions through this transmission of alternating current.

Symptoms of a bad power cord can include:

• Abnormal sounds such as humming or buzzing from within 
• Tripped circuit breakers interfering with operations
• Indicators of cord damage like frays or exposed wiring
• Inconsistencies in interior temperature maintenance

Causes may involve normal wear over extended use, physical stress, or accidental damage to the cord insulation.  

Replacing the power cord assembly with this genuine LG OEM part restores a reliable electrical pathway. It ensures a continued power supply to keep foods fresh and frozen.

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This refrigerator shelf assembly replaces a broken or worn internal shelf to restore usable storage and stable support for food and containers. The glass shelf provides a flat, easy-to-clean surface that maintains organized chilling. What it does

• Replaces a damaged or cracked internal refrigerator shelf to restore safe storage
• Provides a sturdy, level surface for containers, produce and deli items
• Helps maintain organized interior layout and prevents items from falling
• Compatible with refrigerators that use this exact OEM shelf assembly

• One (1) refrigerator shelf assembly (glass shelf with trim/frame as shipped by manufacturer)

• Remove power or disconnect the appliance before performing service when required by your model's safety instructions
• Handle glass parts carefully; wear gloves to avoid cuts and support the shelf during removal and installation
• Verify exact fit and orientation before tightening any retainers; do not force the shelf into slots