Lrsc 26915Sw Parts

This small torsion spring restores tension to the dispenser ice door lever so the chute door snaps closed after dispensing. It helps keep warm air and moisture out, reducing frost, condensation, and stray ice from the dispenser.

• Provides return tension for the dispenser ice chute door/lever
• Helps the chute door seal properly to limit warm air infiltration
• Worn or broken springs may cause the ice door to stay open or close slowly
• Symptoms can include frost/ice buildup in the chute, moisture at the dispenser, or cubes dropping/clumping

• Unplug the refrigerator or switch off the circuit breaker before servicing
• Remove the dispenser trim/panel to access the ice door mechanism; note spring orientation with a photo
• Use needle-nose pliers and eye protection—small springs are under tension and can snap
• After installation, cycle the dispenser to confirm the door opens/closes freely and seals

This evaporator fan motor assembly circulates cold air across the evaporator coils and throughout the cabinet to keep temperatures even. Replacing a worn motor restores airflow and helps reduce warm spots and grinding or squealing fan noise. What it does:

• Circulates air across the evaporator and through vents to cool the refrigerator and freezer compartments
• Helps maintain uniform temperatures and consistent airflow throughout the cabinet
• Common failure signs: weak or no airflow, refrigerator section warmer than the freezer, or whining/rattling fan noise
• Fan typically runs only with the door switch closed; lack of operation with the switch closed can indicate a failed motor

• Includes: 1 evaporator fan motor assembly

• Disconnect power before servicing; interior panels and liners can have sharp edges
• Access is typically behind the rear panel of the freezer or fresh food section (varies by model)
• Disconnect the wiring harness, remove the old assembly, and install the new one securely with wiring routed clear of the blade
• Restore power and depress the door switch to verify fan operation and airflow

This leveling leg assembly stabilizes and levels your refrigerator so it sits solidly on the floor and the doors align correctly. Replacing a worn or stripped leg helps reduce rocking and vibration and restores smooth leveling adjustment.

• Provides height adjustment to level the cabinet on uneven floors
• Supports the unit to prevent rocking or wobbling
• Helps doors close and seal properly when the cabinet is level
• Symptoms may include persistent wobble, vibration/rattling, or a stripped/bent foot or screw

• Unplug the refrigerator and use a helper to prevent tipping injuries.
• Protect flooring; remove the kickplate/grille for access if present.
• Thread out the worn leg; hand-thread the new assembly and adjust height—do not over-extend.
• Level side-to-side and front-to-back per your owner's manual, then reattach any panels.

THERMISTOR ASSEMBLY,PTC

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

Replace a worn door gasket to restore a tight seal on your refrigerator door. This perimeter seal keeps cold air in and humid air out to stabilize temperatures, reduce frost and condensation, and support efficient, consistent cooling.

• Creates an airtight seal between the door and cabinet
• Helps maintain proper internal temperature and humidity
• Reduces frost, sweating, and energy loss from air leaks
• Common symptoms: torn or hardened gasket, visible gaps, door not sealing, moisture or frost near the door

• Disconnect power before servicing
• Warm the new gasket in hot water or with a hair dryer on low to relax and straighten it
• Remove the old gasket and clean the mounting channel and mating surfaces
• Install starting at the corners and press fully into the channel; verify even contact and proper door closure

This vegetable tray assembly provides the stable bottom surface for the refrigerator crisper so produce stays organized and contained. Replace a cracked, warped or missing tray to restore proper storage and prevent items from shifting. What it does:

• Serves as the bottom shelf for the vegetable/crisper compartment to keep produce contained and organized
• Restores support when the original tray is cracked, broken or missing
• Helps prevent items from sliding into the drawer gap or contacting interior components
• Keeps the crisper area cleaner and easier to wipe down

• Typically installs by sliding into the crisper/drawer rails; check orientation before seating
• Handle carefully — plastic or glass trays can chip or crack during handling
• Follow safety precautions

Replacement vegetable drawer tray assembly that restores the refrigerator's crisper storage area, keeping produce contained and organized while preventing spills from reaching lower shelves. Installs as a direct replacement for damaged or missing drawers. What it does:

• Provides a removable storage bin for fruits and vegetables to keep items organized and contained.
• Replaces cracked, broken, warped, or missing drawers that don't slide or hold items properly.
• Contains spills and makes cleanup easier by keeping liquids and debris confined to the drawer.
• Interfaces with the existing crisper rails and cover so the compartment functions as intended.

• Remove food and any loose shelves or covers before installing; handle plastic parts carefully to avoid cracks.
• Slide the drawer onto the existing rails/guides until it seats; alignment may require lifting or lowering the rails slightly.
• If the drawer does not slide smoothly, inspect rails/glides for damage or debris and clean or replace as needed.

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power

Color: white. Measures about 14 inches wide by 9 inches high by 19 inches deep.

This is the water injector tube for select refrigerators. It routes water from the supply system into the appropriate internal channel, helping ensure proper flow to the ice maker or dispenser and preventing leaks at the connection point.

• Directs water from the valve/supply line into the refrigerator's internal water path
• Helps restore proper ice maker/dispenser filling
• Common symptoms: leaking at the rear/under the unit, poor or no ice production, slow or no dispenser flow

• Unplug the refrigerator and shut off the water supply before service
• Have a towel ready to catch residual water from the line
• Note tube routing and connection points before removal; push-to-connect fittings may be present
• After installation, turn water on and check all joints for leaks

Due to manufacturer changes you must also order the frame 3210JA0006S to make this work. This funnel now only has four tabs instead of six.

This is a complete refrigerator ice maker assembly that automatically forms, freezes, and ejects ice cubes into the bin. It restores consistent ice production when the original ice maker stops cycling or no longer makes ice. What it does

• Freezes water in its mold, then harvests and ejects cubes into the ice bucket each cycle
• Controls fill and harvest timing and signals the water inlet valve during the fill portion of the cycle
• Stops ice production when the bin is full via its shutoff mechanism
• Typical failure symptoms: no ice, intermittent/low ice output, or cubes not ejecting

• 1 ice maker assembly

• Disconnect power and turn off the household water supply before servicing
• Remove the ice bin; loosen mounting screws, disconnect the wire harness, and swap in the new assembly in the same position
• Inspect and clear the fill tube of any ice blockage before reconnecting
• Restore power and water; allow the unit to reach operating temperature and begin cycling

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

This evaporator fan motor assembly moves cold air across the evaporator and throughout the fresh food compartment to keep temperatures even and cooling consistent. Replace it to restore proper airflow and help eliminate warm spots or frost buildup. What it does

• Circulates chilled air from the evaporator into the refrigerator section
• Helps maintain stable temperatures and consistent cooling performance
• Replaces a motor that is noisy, stalls intermittently, or doesn't run
• Helps with symptoms like weak/no airflow from refrigerator vents, a warm fridge compartment, or ice/frost on the rear interior panel

• One refrigerator fan motor assembly

• Disconnect power to the refrigerator before servicing
• Access the assembly behind the rear interior panel of the refrigerator section
• Remove the panel, disconnect the wire harness, and release the motor assembly from its mounts; transfer any model-specific fan blade or isolators if required
• Ensure the fan spins freely and wiring is clear of the blade before restoring power; use care around sharp edges and the evaporator coil