M-Ffc13k2cw1 Parts

A front roller assembly that supports the dryer's drum edge to help the drum turn smoothly and quietly. Replacing a worn roller restores proper drum alignment and helps reduce rubbing, squeaks, and uneven spinning. What it does:

• Supports the front of the dryer drum so it rotates freely and stays centered.
• Reduces noise and vibration caused by worn or rough rollers.
• Prevents drum wobble that can cause rubbing against the cabinet or seals.
• Helps the drum turn smoothly so airflow and drying performance remain consistent.

• Disconnect power before any service. For gas dryers, turn off gas supply if required by your local codes.
• Remove the dryer front panel or cabinet as required to access the drum; support the drum while removing and installing the roller.
• Inspect related parts (rear roller/glides, drum seals, belt) and replace if worn to avoid repeat failures.
• Use common hand tools; do not force parts. Follow OEM service instructions for torque/fastening details.

This factory screw secures appliance panels, brackets, or trim. Replace a missing, stripped, or rusted fastener to restore a tight, rattle-free fit and keep components properly aligned in the intended OEM locations. What it does

• Fastens brackets, trim, or sheet-metal panels to the chassis
• Replaces worn, rusted, or missing hardware
• Helps eliminate loose panels, vibration, and misalignment
• Restores proper fit and support for affected assemblies

• Includes 1 screw

• Disconnect power and shut off gas/water before servicing
• Match this screw to the original location; lengths and thread types can vary by position
• Use the correct driver; start by hand and do not overtighten to avoid stripping threads
• If the receiving threads are damaged, repair/replace the mating clip or insert before installing

This door hinge supports the appliance door and provides a smooth pivot point so it opens and closes correctly. A worn hinge can cause sagging, rubbing, or poor sealing that affects performance and safety. What it does:

• Supports and guides the door for smooth opening and closing
• Helps maintain correct door alignment and sealing
• Common symptoms include door sagging, rubbing/binding, squeaking, or not closing flush
• Replace if the hinge is bent, cracked, loose, or excessively worn

• One door hinge

• Disconnect power to the appliance before servicing
• Support the door during removal/installation; some hinges are spring-loaded—use caution
• Remove any panels/trim as needed and transfer spacers/bushings from the old hinge if present
• Adjust mounting points as needed per the service manual

This user interface panel is the touch-control assembly for your appliance. It registers button presses and drives the indicator lights, allowing you to select settings and view operating status when the original interface becomes unresponsive. What it does:

• Provides the touch/button inputs users press to choose options
• Sends those inputs to the main control for processing
• Illuminates indicators to show setting and cycle/status feedback
• Typical failure symptoms: unresponsive or intermittent controls, some keys not working, lights not illuminating or flickering, inability to start or change settings

• 1 user interface panel assembly

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access the console area, remove mounting screws/clips, and carefully release the old UI
• Handle the circuit board by the edges and observe anti-static precautions
• Transfer any brackets/clips as needed, reconnect harnesses fully, and secure the panel before restoring power

The Rail is an OEM part for Whirlpool side-by-side refrigerators. It forms an adjustable track system that refrigerator shelves easily glide on.

Causes of a bad rail can include dents or bending over time, especially near weight-bearing points where shelves rest. Normal wear from repeated shelf insertion/removal may also weaken track brackets. 

Symptoms of a bad rail include:

• Shelves that stick or are difficult to maneuver  
• Sagging or uneven weight distribution on one side
• MissingSnap clips or brackets destabilizing shelves
• Rattling or noise particularly during opening/closing 

This Whirlpool OEM rail replacement ensures smooth, quiet operation by restoring sturdiness and precise alignment. Compatible with brands including KitchenAid, Jenn-Air, and Kenmore.

Note: Right Hand Encap

The Pantry Endcap is an OEM part for Whirlpool refrigerators. As an important structural component, the pantry endcap provides structural integrity to the pantry bin as well as protection for the outer wall. It is specifically designed to fit seamlessly within the pantry to improve organization and optimize storage space.

Causes of a bad pantry endcap are typically wear and tear over time from repeated impacts, especially along the edges.

Symptoms of a damaged pantry endcap include:

• Visible dents, cracks or holes in the material
• Difficulty fully closing or sealing the pantry bin
• Reduced insulation value leading to warmer temperatures inside
• Inability to attach or mount accessories in the pantry area

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

A general-purpose 6-20 screw used to secure panels, brackets and small components on Whirlpool appliances. Replaces stripped or missing fasteners to restore a snug fit and reduce rattling or loose parts. What it does:

• Secures appliance panels, trim, brackets and internal components in original mounting locations.
• Stops panel movement, vibration noise and loose connections caused by missing or corroded screws.
• Fits the OEM 6-20 thread designation used on multiple Whirlpool assembly points.
• Sold individually for spot repairs and small part replacements.

• Disconnect power or gas supply to the appliance before starting any repair.
• Use the correct screwdriver or bit to avoid stripping the head; tighten until snug but do not overtighten.
• Replace like-for-like; stop and verify the correct fastener for the mounting point.
• Check the appliance's parts diagram for the exact screw location and orientation.

Size: 8 x 1-1/4 inch.

This drain tube gasket seals the connection between the drain tube and its mating port to prevent leaks. A tight seal helps keep water where it belongs and protects surrounding components from moisture damage.

• Creates a watertight seal at the drain tube connection point
• Can help address water leaks around the drain area
• Deterioration, cracking, or hardening of the old gasket may cause seepage
• Replacing a worn gasket can restore proper leak prevention

• Unplug the appliance and shut off water supply before service
• Place a towel or pan to catch residual water when disconnecting the tube
• Inspect the tube and mating surfaces; clean before installing the new gasket
• Do not overtighten fittings; verify a snug, even seal and check for leaks on first run

This cover replaces a cracked, warped, or missing cover on your appliance. It protects internal components and restores the correct fit and finish so parts stay secured and the unit operates as designed.

• Shields internal components from debris and moisture
• Helps maintain proper airflow, water path, or guarding as designed
• Restores fit/finish and keeps parts secured
• Common signs of failure: cracks, broken tabs, discoloration, or a cover that won't stay in place

• Disconnect power and shut off water/gas before servicing
• Note the original orientation and transfer any screws/clips from the old part
• Align tabs and fasteners; avoid overtightening to prevent damage
• After installation, test operation and ensure no interference or leaks

This hinge cover assembly conceals and protects the door hinge area, providing a clean look while shielding wiring and moving parts from dust and moisture. It restores proper coverage if the original cover is cracked, missing, or loose.

• Covers the hinge area to protect components and improve appearance
• Helps prevent debris intrusion around the hinge mechanism
• Common fix for a broken, missing, or damaged hinge cover
• May help if the hinge area is exposed or rattling due to a loose cover

• Unplug appliance before service; shut off water if applicable
• Use a non-marring tool to release clips or tabs; avoid prying on finished surfaces
• Transfer any reusable screws or trim from the old cover
• Confirm secure engagement of tabs/screws to prevent vibration

This front roller assembly replaces a worn wheel/bracket so the appliance or drawer moves smoothly and stays properly supported. Restore easy glide and alignment to reduce drag, noise, and strain during everyday use.

• Supports the front of the cabinet or drawer and allows smooth rolling
• Helps maintain proper alignment and level during movement
• Reduces scraping, squeaking, or hard-to-move operation
• Common signs of failure: broken/missing wheel, bent bracket, uneven stance, or dragging

• Disconnect power before servicing; shut off water or gas if applicable. Use help when moving heavy appliances
• Support the drawer or appliance and access the front roller mount
• Remove retaining fasteners, noting orientation; transfer any reusable hardware
• Install and secure the new assembly, then check for smooth travel and proper alignment/level

Color: Black

Top hinge assembly restores proper support and a smooth pivot for the refrigerator door, helping maintain alignment and a tight seal. Use this exact replacement when a top hinge is bent, worn, or causing door sag. What it does:

• Provides the upper pivot point that supports the refrigerator door and enables smooth opening and closing.
• Restores proper door alignment to help eliminate sagging, uneven gaps, or rubbing at the top edge.
• Replaces worn, bent, or damaged hinge components that cause wobble or inconsistent door movement.
• Works with factory mounting locations and hardware to return the door to intended operation.

• Disconnect power to the appliance and remove items from the door before beginning work.
• Support the door (have a second person assist) when removing or installing the top hinge to prevent injury or damage.
• Use appropriate hand tools; snug mounting screws securely but avoid over-tightening.

This replacement divider separates sections inside a bin or drawer so contents stay organized and in place. Replacing a cracked or missing divider restores proper fit and helps prevent items from shifting or jamming during everyday use. What it does

• Divides a bin, basket, or drawer into sections for better organization
• Helps keep small items upright and prevents contents from sliding together
• Seats into molded slots or tabs to maintain the correct layout
• Common symptoms include cracks, broken tabs, warping, or the divider not staying in place

• 1 divider

• Unplug the appliance before servicing
• Remove the bin/basket or drawer to access the divider
• Release the old divider from its slots or tabs; align and press the new divider firmly into place
• Verify the divider is fully seated and the bin/drawer installs and moves correctly before restoring power