Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Secures wire harness connections in your washer. Replace if clip is broken, cracked, or missing to prevent loose wiring. Verify fit with your model number.
Connector for washer water supply lines. Replaces cracked, corroded, or leaking connectors. Essential for secure installation and proper water flow.
Here's the story. All my appliances except the dryer broke. Yeah. talk about bad luck. First I tried to fix the refrigerator. Replaced both motherboard and inverter board. Now it wakes up but the compressor does not kick in. Need another part. The washer, well I have to pull out the sink to get enough room to pull out the washer to fix it. Since the refriigerator is still in the middle of the kitchen, I don't need to tear apart another room. Nevertheless, let me say this, I love my "older"... Read more
Plastic snap-in clip secures washer panels and trim pieces, preventing rattles and sagging. Replace when broken or loose to restore secure fit.
Fix a washer that won't fill, fills slowly, or leaks during the fill cycle. This water inlet valve controls water flow into your washer. DIY repair.
Secures washer hoses to fittings for leak-free connections. Replace when worn, cracked, or lost to keep hoses stable. Verify fit with your model number.
Machine screw fastens panels, brackets, and components inside appliances. Replace stripped, missing, or loose screws to restore secure assembly.
Fix igniter sparking issues or non-responsive controls with this range rocker switch. Direct replacement part for common control panel failures.
Secures wiring bundles inside your microwave. Replace this wire tie if it's cracked, broken, or missing to keep internal wires organized and secure.
Secures panels and components in place. Replace this fastener if stripped, corroded, or missing to restore proper alignment and eliminate rattling.
Ordered boot watched video had no trouble finding ,parts easily entered part num,no problems at all Read more
Fix washer leaks and poor draining with a new tub-to-pump hose. Carries water from the outer tub to the drain pump. DIY repair takes just minutes.
Model# MAV7257AWW Maytag Atlantis Washing Machine. Repairs were fairly easy along with the videos appliancepartspros offers on their website. Parts also came with instructions on how to install. Other videos were available on You Tube. The only part difficult to install was Thrust bearing kit - make sure when installing to pull down on shaft so washer and e-clip will fit. Another note, you can get a pulley for your replacement motor pulley on eBay and Maytag.com. Just pay close attention to... Read more
Usually ships within 4 - 14 days
Fix a washer that won't advance cycles, stalls mid-wash, or skips spin. This timer controls your wash program. DIY-friendly, 10-15 minute repair.
Replaced washer timer. Confirmed that old/broken timer had burnt (open) internal contacts. Read more
Fixes squealing or slow stopping at end of spin cycle. This spring maintains brake tension so the basket stops promptly. DIY repair takes about 1 hour.
I replaced the: brake stator, rotor, and snubber ring. I did need to remove the stator which allowed the spring to decompress. I used 2 C-clamps to control the force when it was removed. To re-secure all the components I stood on the stator to compress the 200lbs spring until the screws could take the load safely. The entire thing took about an hour to slowly go through everything. Read more
Gray selector knob for washer control panels. Replaces broken, cracked, or missing knobs. Push-on installation. 1-inch base, 2-inch handle diameter.
Ordered part. Fast and in-stock. Read more
Filters debris and sediment from incoming water before it reaches the inlet valve. Replace if clogged or missing to restore proper fill flow. Confirm fit.
The machine would not run a full cycle before it cut off and had the code "FE" and water was too high. The water inlet valve needed to be replaced since it was letting in too much water at time. The repair was easy. Unplug machine and turn off cold water. Remove cold water line and drain water into bucket. Remove back two braces located at the top on each end of machine This will allow you to move top cove back about one inch. Pull back top cover about 1 inch then lift off cover. Remove... Read more
Washer won't spin or agitate? This lid switch assembly senses when the lid is closed, enabling spin cycles. Moderate DIY repair restores safe operation.
Replaced entire switch assembly Read more